Advertisement
Quick Links
AT Wizard M5
The 5th generation of our angle & throw measuring device
The AT Wizard M5 is a measuring device for determining flap angle and flap
travels.
The display is either via the built-in display or via an app, which we provide
free of charge.
The app is only available for Android and Apple IOS systems. Normally, all
smartphones and tablets should work as long as they support the low-power
operation of Bluetooth. It should work with Bluetooth from version 2.1.
Download the app for Android or IOS. Search for the app "AT Wizard" in the
respective stores (Android or Apple) and install it. If you are asked for location
sharing permission when you first start it, please enable it. This is unfortunately
asked by Android to check if the app is enabled for the respective region.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for DigiTech AT Wizard M5
Summary of Contents for DigiTech AT Wizard M5
- Page 1 AT Wizard M5 The 5th generation of our angle & throw measuring device The AT Wizard M5 is a measuring device for determining flap angle and flap travels. The display is either via the built-in display or via an app, which we provide free of charge.
- Page 2 Design of the AT Wizard M5 The AT Wizard M5 has 3 buttons. On the top side is the power button.When this button is pressed for approx. 1 second, the device switches on. A further press of approx. 6 seconds will swicth the device off again.
-
Page 3: First Start
First measurements Attach the AT Wizard M5 to your flap. This can be done with a small piece of double stick tape or with the optional holder. Now the display must be set to 0. After the start of the AT Wizard M5, the menu is set to the function "ZERO", so now you only have to press the select... - Page 4 If you now move the flaps, you can already read off the angle. In many cases, the manufacturers will specify the flap travel in mm. If you want to know this, then we must first specify the flap depth so that the AT Wizard M5 can convert the angle into travel in mm..
- Page 5 We use the built-in position sensor of the AT Wizard M5 to set the value higher or lower. So if your flap depth is more than 50 mm, then move the flap up a little bit and press the select button several times until the correct value is displayed.
- Page 6 Wizard M5. Press the button on the AT Wizard M5 for about 2 seconds. The menu will appear on the screen. Please do not try to install the AT Wizard M5 or its Bluetooth connection manually via the Bluetooth Manager. Just start the app and switch on the AT Wizard.
- Page 7 Now enter the depth of your flap in mm in the "CHORD" field so that the AT Wizard M5 can convert the angular degrees into travel in mm. To do this, simply tap on the "Chord" field. An input window will now open. If you only want to know the angle, you do not need to do this.
- Page 8 IOS, up to 4 AT Wizards M5 can be operated simultaneously. To do this, proceed as follows.. When the app has detected the first AT Wizard M5, turn on the the next AT Wizard and so on. The screen will split and show the different displays.
- Page 9 Attention : Android 9+10 users Since the introduction of Android 9+10, features that affect the AT Wizard app have changed for security reasons. Bluetooth and location detection must be turned on tu use the app. After installing the AT Wizard app, the following change only needs to be made once on Android 9+10.
-
Page 10: Calibration Menu
Calibration menu Sometimes it is necessary to Calibrate the accel sensors inside the device. This is done thru a setup menu. How to Proceed? 1. Turn Devise off 2. Turn upside down (display downwards) 3. Now press in the following sequence : 1 M5 button and hold / 2 secondary button and hold / 3 power button and hold. - Page 11 The sign of the crossed-out wheeled garbage can means that this product must be taken to a collection point for electronic waste Die CE Erklärung des Herstellers Digitech liegt uns vor, diese können wir Ihnen auf Anforderung gerne zusenden.
Need help?
Do you have a question about the AT Wizard M5 and is the answer not in the manual?
Questions and answers
My M15 doesn't charge. The screen lights up when power is connected - but no 'plug' symbol and battery does'nt charge. Is there a fix?
If the screen lights up but the battery does not charge, try the following steps:
1. Ensure you are using a USB-C cable, as required for charging.
2. Check for the battery symbol in the bottom right of the screen and a plug symbol during charging to confirm it is charging.
3. If the plug symbol does not appear, try a different USB-C cable or charging adapter.
4. Make sure the USB-C port on the device is clean and undamaged.
If the issue continues, the device may need service or replacement.
This answer is automatically generated