Table of Contents
Advertisement
4
SECTION 00 - MAINTENANCE - CHAPTER 1
•
Always use lifting equipment and similar of ap-
propriate capacity to lift or move heavy compo-
nents.
•
Pay special attention to bystanders.
•
Never pour gasoline or diesel oil into open, wide
and low containers.
•
Never use gasoline, diesel oil or other flammable
liquids as cleaning agents. Use non-flammable
non-toxic proprietary solvents.
•
Wear protection goggles with side guards when
cleaning parts using compressed air.
•
Do not exceed a pressure of 2.1 bar, in accor-
dance with local regulations.
•
Do not run the engine in a closed building without
proper ventilation.
•
Do not smoke, use open flames, cause sparks in
the nearby area when filling fuel or handling high-
ly flammable liquids.
•
Do not use flames as light sources when working
on a machine or checking for leaks.
•
Move with caution when working under a Ma-
chine, and also on or near a Machine. Wear prop-
er safety accessories: helmets, goggles and spe-
cial footwear.
•
During checks which should be carried out with
the engine running, ask an assistant to seat at the
operator's seat and keep the service technician
under visual control at any moment.
•
In case of operations outside the workshop, drive
the Machine to a flat area and block it. If working
on an incline cannot be avoided, first block the
Machine carefully. Move it to a flat area as soon
as possible with a certain extent of safety.
•
Ruined or plied cables and chains are unreliable.
Do not use them for lifting or trailing. Always han-
dle them wearing gloves of proper thickness.
•
Chains should always be safely fastened. En-
sure that fastening device is strong enough to
hold the load foreseen. No persons should stop
near the fastening point, trailing chains or cables.
•
The working area should be always kept CLEAN
and DRY. Immediately clean any spillage of wa-
ter or oil.
•
Do not pile up grease or oil soaked rags, as they
constitute a great fire hazard. Always place them
into a metal container.
Before starting the Machine or its attachments,
check, adjust and block the operator's seat. Also
604.56.061.00
09/2000
ensure that there are no persons within the Ma-
chine or attachment operating range.
•
Do not keep into your pockets any object which
might fall unobserved into the Machine's inner
compartments.
•
Whenever there is the possibility of being
reached by ejected metal parts or similar, use
protection eye mask or goggles with side guards,
helmets, special footwear and heavy gloves.
•
Wear suitable protection such as tinted eye
protection, helmets, special clothing, gloves and
footwear whenever it is necessary to carry out
welding procedures. All persons standing in the
vicinity of the welding process should wear tinted
eye protection. NEVER LOOK AT THE WELD-
ING ARC IF YOUR EYES ARE NOT SUITABLY
PROTECTED.
•
Metal cables with the use get frayed. Always
wear adequate protections (heavy gloves, eye
protection, etc.)
•
Handle all parts with the greatest caution. Keep
your hands and fingers far from gaps, moving
gears and similar. Always use approved protec-
tive equipment, such as eye protection, heavy
gloves and protective footwear.
START UP
•
Never run the engine in confined spaces which
are not equipped with adequate ventilation for
exhaust gas extraction.
•
Never bring your head, body, arms, legs, feet,
hands, fingers near fans or rotating belts.
ENGINE
•
Always loosen the radiator cap very slowly be-
fore removing it to allow pressure in the system
to dissipate. Coolant should be topped up only
when the engine is stopped or idle if hot.
•
Do not fill up fuel tank when the engine is running,
mainly if it is hot, to avoid ignition of fires in case
of fuel spilling.
•
Never check or adjust the fan belt tension when
the engine is running.
Never adjust the fuel injection pump when the
Machine is moving.
•
Never lubricate the Machine when the engine is
running.
LB 75-115
Hide quick links:
Advertisement
Table of Contents
