IDEC MICRO/I HG2G Series Instruction Sheet

INSTRUCTION SHEET
Operator Interface
Confirm that the delivered product is what you have ordered. Read this instruction sheet to make
sure of correct operation. Make sure that the instruction sheet is kept by the end user.
SAFETY PRECAUTIONS
In this operation instruction sheet, safety precautions are categorized in order of importance to
Warning and Caution:
Warning notices are used to emphasize that improper operation may cause severe personal
injury or death.
Caution notices are used where inattention might cause personal injury or damage to equipment.
● When using the HG2G in applications which require high reliability and safety, such as
nuclear equipment, railways, aircraft, medical equipment, and vehicles, add a failsafe or
backup functionality and verify an adequate level of safety using the product specifications.
● Turn off the power to the HG2G before installation, removal, wiring, maintenance, and
inspection of the HG2G. Failure to turn power off may cause electrical shock or fire hazard.
● Special expertise is required to install, wire, configure, and operate the HG2G. People
without such expertise must not use the HG2G.
● The HG2G uses an LCD (liquid crystal display) as a display device. The liquid inside the
LCD is harmful to the skin. If the LCD is broken and the liquid attaches to your skin or clothes,
wash the liquid off using soap, and consult a doctor immediately.
● Emergency and interlocking circuits must be configured outside the HG2G.
● Replace battery with UL recognized battery, model CR2032 only. Use of another battery may
present a risk of fire or explosion. See instruction sheet for safety instructions.
● Install the HG2G according to the instructions in the Instruction Manual. Improper installation
will result in falling, failure, electrical shock, fire hazard, or malfunction of the HG2G.
● The HG2G is designed for use in pollution degree 2. Use the HG2G in environments of
pollution degree 2.
● The HG2G uses "PS2 of EN61131" as DC power supply.
● Prevent the HG2G from falling while moving or transporting, otherwise damage or
malfunction of the HG2G will result.
● Prevent metal fragments or wire chips from dropping inside the HG2G housing. Ingress of
such fragments and chips may cause fire hazard, damage, and malfunction.
● Use a power supply of the rated value. Using a wrong power supply may cause fire hazard.
● Use wire of a proper size to meet the voltage and current requirements.
● Use fuses or circuit protectors on the power line outside the HG2G.
● When exporting the HG2G to Europe, use an EN60127 ( EC60127) approved fuse or an
EU-approved circuit protector.
● Do not push hard or scratch the touch panel and protection sheet with a hard object such as
a tool, because they are damaged easily.
● Make sure of safety before starting and stopping the HG2G. Incorrect operation of the HG2G
may cause mechanical damage or accidents.
● When disposing of the HG2G, do so as an industrial waste.
UL/c-UL Compliance and Handling Cautions
● This equipment is suitable for use in Class Ｉ , Division 2, Groups A, B, C, D or
Non-Hazardous locations only.
● Warning - Explosion Hazard - Substitution of components may impair suitability for Class I,
Division 2
● Warning - Explosion Hazard - Do not disconnect equipment unless power has been
switched off or the area is known to be Non-Hazardous.
● Replace battery with UL recognized battery, model CR2032 or CR2032H only. Use of another
battery may present a risk of fire or explosion. See instruction sheet for safety instructions.
● Caution - Battery may explode if mistreated. Do not recharge, disassemble or dispose of in
fire.
● Warning - Explosion Hazard – Batteries must only be changed in an area known to be
Non-Hazardous.
● For Indoor Use Only, Pollution Degree 2 Environment, in an area that is dry and free of
contaminates.
● Avertissement: Risque d'explosion. La substitution de composants peut rendre ce matériel
inacceptable pour les emplacements de classe I, division 2.
● Avertissement: Risque d'explosion. Avant de déconnecter l'equipement, couper le courant
ou s'assurer que l'emplacement est désigné non dangereux.
● Avertissement: Risque d'explosion. Afin d'éviter tout risque d'explosion, s'assurer que
l'emplacement est désigné non dangereux avant de changer la batterie.
● Attention: Risque d'explosion de la batterie en cas de mauvaise utilisation. Ne pas recharger,
démonter ou jeter la batterie au feu.
1
Package Content
Before installing the HG2G, make sure that the specifications of the product conform to your
requirements, and that no parts are missing or damaged due to accidents during transportation.
B-1243(5)
HG2G Series
●Main Unit (24VDC Type)
Display Device
RS232C, RS422/485
5.7-inch
RS232C, RS422/485
STN color LCD
RS232C, RS422/485
5.7-inch
RS232C, RS422/485
STN monochrome LCD
●Main Unit (12VDC Type)
Display Device
RS232C, RS422/485
5.7-inch
RS232C, RS422/485
STN color LCD
RS232C, RS422/485
5.7-inch
RS232C, RS422/485
STN monochrome LCD
●Accessories
Mounting Clip (4)
Host communication plug (1)
(Attached to the Main Unit)
Instruction Sheet (Japanese/English)
[This manual] 1 each
2
Type No. Development
HG2G-S#2$*F-%
# Display S: STN color LCD
B: STN monochrome LCD
$ Power supply 2: 24VDC
1: 12VDC
* Interface V: RS232C, RS422/485
T: RS232C, RS422/485 & Ethernet
% Bezel color W: Light gray
B: Dark gray
S: Silver
3
Specifications
UL508, ANSI/ISA 12.12.01
CSA C22.2 No.142
Safety Standards
IEC/EN61131-2
EMC Standards IEC/EN61131-2
Rated Operating Voltage
Power Voltage Range
Power Consumption
Allowable Momentary
Power Interruption
Inrush Current
Dielectric Strength
Insulation Resistance
Backup Battery
Operating Ambient Temperature
Operating Relative Humidity
Storage Ambient Temperature
Storage Relative Humidity
Altitude
Vibration Resistance
(Damage Limits)
Shock Resistance
(Damage Limits)
Pollution Degree
Corrosion Immunity
Degree of Protection
Terminal
Dimensions
Weight (Approx.)
1
Interface Model No.
HG2G-SS22VF-□
HG2G-SS22TF-□
& Ethernet
HG2G-SB22VF-□
HG2G-SB22TF-□
& Ethernet
□ indicates the bezel color.
Interface Model No.
HG2G-SS21VF-□
HG2G-SS21TF-□
& Ethernet
HG2G-SB21VF-□
HG2G-SB21TF-□
& Ethernet
□ indicates the bezel color.
CSA C22.2 No.213
HG2G-S#22*F-% : 24V DC
HG2G-S#21*F-% : 12V DC
HG2G-S#22*F-%
85% to 120% of the rated voltage (24VDC)
HG2G-S#21*F-%
85% to 150% of the rated voltage (12VDC)
(including ripple)
10W maximum
10 ms maximum, Level: PS-2
( EC/EN61131)
HG2G-S#22*F-% : 20A maximum
HG2G-S#21*F-% : 40A maximum
1000V AC, 10 mA, 1 minute
(between power terminals and FG)
50 MΩ minimum (500V DC megger)
(between power terminals and FG)
Built-in CR2032 lithium primary battery
Standard replacement cycle: 5 years
Guaranteed term: 1 year (at 25°C)
0 to 50°C
10 to 90% RH (no condensation)
-20 to 60°C
10 to90% RH (no condensation)
0 to 2000m (operation)
0 to 3000m (transportation) (IEC61131-2)
5 to 9 Hz, amplitude 3.5 mm
2
9 to 150 Hz, 9.8 m/s
X, Y, Z directions for 10 cycles [100 minutes]
(IEC60068-2-6)
2
147 m/s , 11 ms
5 shocks each in 3 axes (IEC60068-2-27)
2 (IEC60664-1)
Free from corrosive gases
P65 *1
TYPE 13 *2
(In the front of panel attachment.)
Power supply terminal: M3
Tightening torque 0.5 to 0.6 N･m
167.2 (W) × 134.7 (H) × 40.9 (D) mm
500g