Advertisement
Operation Guide 5132
Mode Reference Guide
Your watch has four "modes". The mode you should select depends on what you
want to do.
To do this:
•
View the current time in your Home City and in one of
29 cities around the globe
•
Configure Home City and daylight saving time (DST)
settings
•
Configure time and date settings
Use the stopwatch to measure elapsed time
View the current time in one of 29 cities (time zones) around
the globe
Set an alarm time
Selecting a Mode
With this watch, everything starts from the Timekeeping Mode.
To determine the watch's current mode
Check the position of the v Left Dial Hand as shown
under "To select a mode".
To return to the Timekeeping Mode from any other
mode
Hold down C for about two seconds until the watch beeps
twice.
To select a mode
Press C to cycle between the modes as shown below. The v Left Dial Hand
indicates the currently selected mode.
Timekeeping Mode
C
The hand indicates
the day of the week.
Alarm Mode
The hand points to ALM.
Timekeeping
Use the Timekeeping Mode to view the current time and date. To enter the
Timekeeping Mode from any other mode, hold down C for about two seconds.
Hand Functions
z Hour Hand
x Second Hand
c Minute Hand
v Left Dial Hand: Indicates the day of the week.
b Lower Dial Hand: Indicates the current hour in the
n Right Dial Hands:
Indicate the current time in the World Time City in
24-hour format.
m Day
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
To configure Home City settings
Note
•
This watch does not have a city code that corresponds
to Newfoundland.
1.
In the Timekeeping Mode, keep
five seconds) as the x Second Hand moves to the city
code of the currently selected Home City.
•
This indicates the city code setting mode.
•
The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
•
For details about city codes, see the "City Code
Table".
2.
To change the Home City setting, press
x Second Hand clockwise.
•
Keep pressing
at the city code you want to select as your Home City.
•
Each time you select a city code, the
c Minute Hand, b Lower Dial Hand and m Day
move to the current time and date for that city code.
Do not perform the next operation until these hands
stop moving.
3.
Press
B to toggle the time for the currently selected
city code between STD (standard time)/DST (daylight
saving time).
•
In the city code setting mode, the
v Left Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
•
Note that you cannot switch between
STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
4.
After the setting is the way you want, press
Enter this mode:
Timekeeping Mode
Stopwatch Mode
World Time Mode
Alarm Mode
Stopwatch Mode
The hand points to 0.
World Time Mode
The hand points to STD
or DST.
Home City time in 24-hour format.
A depressed (for about
D to move the
D until the x Second Hand is pointing
z Hour Hand,
A to return to the Timekeeping Mode.
To toggle the Home City time between standard time and daylight saving time
1.
Perform the step 1 under "To configure Home City settings".
•
Each time you select a city code, the
z Hour Hand, c Minute Hand, and
b Lower Dial Hand move to the current time for that city code. Do not perform
the next operation until these hands stop moving.
2.
Press
B to toggle the time for the city code of the currently selected Home City
between STD (standard time)/DST (daylight saving time).
•
In the city code setting mode, the
v Left Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
•
Note that you cannot switch between
STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
3.
After the setting is the way you want, press
Note
•
After you specify a city code, the watch will use UTC* offsets in the World Time
Mode to calculate the current time for other time zones based on the current time
in your Home City.
Coordinated Universal Time, the world-wide scientific standard of timekeeping. The
*
reference point for UTC is Greenwich, England.
Configuring Current Time and Date Settings
You can configure current time and date settings.
To change the current time setting
1.
In the Timekeeping Mode, keep
five seconds) as the x Second Hand moves to the city
code of the currently selected Home City.
•
At this time, the
Home City's current daylight saving time setting (STD
or DST).
2.
Change the Home City and daylight saving time (DST)
settings, if you want.
•
For details about these settings, see steps 2 and 3
under "To configure Home City settings".
•
In the following steps, each press of
between settings as shown below.
Home city/DST
3.
Press
C.
•
The watch will beep, and the
x Second Hand and v Left Dial Hand will move to
their 12 o'clock positions. This is the time setting mode.
4.
Use
D (+) and B (–) to change the time (hour and minute) setting.
•
Each press of either button will move the hands (
Hand) one minute.
•
Holding down
D or B will start high-speed z Hour Hand and c Minute Hand
movement in the applicable direction. To stop high-speed hand movement,
press any button.
•
The
b Lower Dial Hand and z Hour Hand move in sync with each other.
•
When setting the time, make sure that the
proper a.m./p.m. hour.
•
If you want to change the date setting at this time, press
procedure starting from step 3 under "To change the current date setting".
5.
After the time setting is the way you want, press
Mode.
•
This will cause the
x Second Hand to move automatically to 12 o'clock and
resume movement from there.
To change the current date setting
1.
In the Timekeeping Mode, keep
00
(for about five seconds) as the x Second Hand
10
moves to the city code of the currently selected
Home City.
2.
Press
20
•
The watch will beep and change to the year
90
30
setting mode.
•
80
40
The year can be set in the range of 2000 to
2099.
•
You can save your settings and exit the
70
50
setting procedure at any time by pressing A,
60
which will return to the Timekeeping Mode.
Setting the year (tens digit)
This will cause the x Second Hand to move
automatically to 12 o'clock and resume normal
movement from there.
3.
Use
D to change the tens digit of the year setting.
•
Each press of
D will move the x Second Hand and change the tens digit of the
year setting.
4.
After the tens digit of the year setting is the way you want, press
•
The watch will beep and change to the ones digit of the year setting mode.
0
5.
Use
D to change the ones digit of the year
setting.
1
•
Each press of
Hand and change the ones digit of the year
setting.
2
6.
After the ones digit of the year setting is the way
9
3
you want, press C.
8
4
•
The watch will beep and change to the month
setting mode.
7
5
6
Setting the year (ones digit)
A to return to the Timekeeping Mode.
A depressed (for about
v Left Dial Hand will indicate the
C cycles
Hour/Minute
Year
Day
Month
z Hour Hand and c Minute
b Lower Dial Hand indicates the
C and perform the
A to return to the Timekeeping
A depressed
C twice.
C.
D will move the x Second
2
Hide quick links:
Advertisement
