Advertisement
Quick Links
Carport Extension
BCCPSW1800EXT / BCCPSW1825EXT
Assembly Instructions
IMPORTANT
Please read these instructions thoroughly before starting assembly.
Check all parts are present before assembly, call 020 3011 2040 for replacement parts.
These instructions should be kept in a safe place for future use.
Advertisement
Related Manuals for Norfolk Greenhouses BCCPSW1800EXT
Summary of Contents for Norfolk Greenhouses BCCPSW1800EXT
- Page 1 Carport Extension BCCPSW1800EXT / BCCPSW1825EXT Assembly Instructions IMPORTANT Please read these instructions thoroughly before starting assembly. Check all parts are present before assembly, call 020 3011 2040 for replacement parts. These instructions should be kept in a safe place for future use.
- Page 2 Canopy Introduction Thank you for your purchase of our Carport Extension, we hope you enjoy. Please read through these instructions and familiarise yourself with the construction process before you begin. We operate a programme of continuous product improvement and we reserve the right to change the specification without prior notice, the latest model is supplied.
- Page 3 • Ladder • Tape Measure Maintenance • It is advised that periodically or after storms or gales you check all nuts, bolts and screws, and tighten where necessary. • Clean using warm soapy water and a non-abrasive cloth. © Norfolk Greenhouses...
- Page 4 Parts List Canopy Framework RL18 RL17 PST1 (2.0m model) RL17A PST3 (2.5m model) RL16 GUT1900W XL71...
- Page 5 Contact Support on 020 3011 2040 Roof Sheets (1140mm x 1830mm) (1140mm x 940mm) © Norfolk Greenhouses...
- Page 6 Parts List Canopy Hardware WRUS1 HBDT WRKS1 NYLOC STUD30 CBM6X80 ST4X34 ST8X5 SC6X32 MM7X60...
- Page 7 All instructions are written for extension to the right of the existing structure, if extending to the left see UNIQUE STEP A (page 18). Remove roof sheets on the side of which your extension will adjoining. Remove all fixings for beam which will be replaced by RL18. © Norfolk Greenhouses...
- Page 8 Frame Assembly Canopy Step 1 - Replace RL20 of existing structure with RL18 Step 2 - Fix HBD bracket to end of RL17A...
- Page 9 Drill 3 holes using Ø6mm masonry drill bit. Fix to wall using provided fixings as shown. (If fixing into timber, use appropriate fixings - not provided) Step 4 - Add CP6 to the LEG then fix BM1 between the Leg and RL17A © Norfolk Greenhouses...
- Page 10 Frame Assembly Canopy Step 5 - Fix RL17 as front beam between existing structure and LEG Step 6 - Fasten 2x HBD brackets to BM1 as shown...
- Page 11 Contact Support on 020 3011 2040 Step 7 - Attach 2x RL16 Step 8 - Fix XL71 to underside of BM1. Push fit HBP to exposed end of front beam © Norfolk Greenhouses...
- Page 12 Roof Assembly Canopy ROOFING NOTE: The following roof sheet layout applies to a New Build structure. If building as part of a retrofit to existing structure, follow the existing roof sheet layout. Step 9 - Fix SR6 roof sheet to the front left corner of the roof frame Place first sheet of SR6 in the front left corner of the roof, position so that there is a 50mm...
- Page 13 Fix with 8x SC6X32 every 3rd corrugation as shown. Step 11 - Fix exposed edge of last SR6 sheet to BM1 Fix using 4x SC6X32 as shown leaving space at the top of sheet for SR7 to overlap. © Norfolk Greenhouses...
- Page 14 Roof Assembly Canopy Step 12 - Position SR7 on top of first SR6, tight against the wall and fix. Fix using 9x SC6X32 on exposed edge and every 3rd corrugation as shown. Step 13 - Fix remaining 5x SR7 sheets Fix each sheet using 8x SC6X32 every 3rd corrugation as shown.
- Page 15 Contact Support on 020 3011 2040 Step 17 - Fix exposed edge of last SR7 sheet to BM1 Fix using 3x SC6X32 as shown . © Norfolk Greenhouses...
- Page 16 Gutter Assembly Canopy Step 18 - Assemble gutter and fix to front beam of carport...
- Page 17 Step 19 - Assemble and fix downpipe to LEG Step 20 - Anchor feet to the ground Use spirit level to align legs in the upright position. Fix to the ground through holes in steel foot using appropriate fixings (not supplied). © Norfolk Greenhouses...
- Page 18 Unique Steps Canopy UNIQUE STEP A - (constructing extension to the left of existing structure) Use hand saw to cut 66mm from end of front beam and remove. This will allow RL17 to pick up on the two end fixings. Continue to Step 2, same build method applies, adapt instructions to suit left side of structure.
- Page 19 Contact Support on 020 3011 2040 © Norfolk Greenhouses...
- Page 20 Canopy Norfolk Greenhouses 1 Vincent Avenue Crownhill Industry Milton Keynes MK8 0AB Tel: 020 3011 2040 E-mail: info@norfolk-greenhouses.co.uk...