S1 Service manual General INTRODUCTION SCOPE OF THIS MANUAL This manual is intended for use by experienced technicians familiar with similar types of commercial grade communications equipment. It contains all required service information for the equipment and is current as of the publication data. Changes which may occur after publication are covered by either Service Bulletins or Manual Revisions.
S1 Service manual REALIGNMENT 1 MODE User Mode PC Mode Manufacture Mode MODE FUNCTION User Mode Use this mode for normal operation Use this mode, to make various settings by PC Mode means of the FPU through RS-232C port. Use this mode, to realign the various...
Page 5
Preface The transceiver is programmed by using a personal computer, programming interface and programming software (ABELL transceiver programming software). The programming software can be used with and IBM PC or compatible. Figure 1 shows the setup of an IBM PC for programming.
S1 Service manual ·Interface cable description (PC programming interface cable:Option) The interface cable is required to connect S-1 to the PC. It has a circuit in their D-sub connection (9-pin) cases that convert the RS-232C logic level to the transistor logic lever. The cable connects the side panel jacks of the A-80 to the PC’S RS-232C serial port.
Page 7
S1 Service manual Separating the chassis from the unit 1.Remove 8 pcs screw⑿。 2.Remove the solder from antenna terminal using a soldering iron and then lift the unit from the chassis⒀ 3.Remove 2 pcs screw⒁ and remove the antenna connector。...
S1 Service manual Remove battery clip 1. Lift up the battery metal reed and press the battery clip at the same time, then remove it in the direction of arrow NOTE:To be sure not broken the battery lock and belt clip...
Page 9
S1 Service manual 1.Radio Principle: 1. Frequency configuration The receiver utilizes double conversion. The first IF is 21.70MHz and the Second IF is 450 KHz. The first local oscillator signal is supplied from the PLL circuit. The PLL circuit in the transmitter generates the necessary frequency.
Page 10
S1 Service manual to further remove spurious signals. 3) IF amplifier The first IF signal is amplified by Q23, and then enters IC7(modulation processor IC). The signal is heterodyned again with a second local oscillator signal within IC7 to create a 450MHz second IF signal.
Page 11
S1 Service manual 1) PLL The frequency step of the PLL circuit is 2.5 or 3.125 or 5 or 6.25KHz. A 13MHz reference oscillator signal is divided at IC4 by a fixed counter to produce the 2.5 or 3.125 or 5 or 6.25 KHz reference frequency.
Page 12
S1 Service manual 2) QT/DQT encoder A necessary signal for QT/DQT encoding is generated by IC5 and modulated at the VCO and X1. C142 3) VCO and RF amplifier...
Page 13
S1 Service manual The transmit signal obtained from the VCO buffer amplifier Q9, is amplified by Q10. This amplified signal is passed to the power amplifier, Q18 and Q29, which is capable of producing up to 1W of RF power.
Page 29
S1 Service manual NLV25T-R22J-PF 2520 Wired Inductor NLV25T-1R0T-PF 2520 Wired Inductor NLV25T-2R2T-PF 2520 Wired Inductor MLF1608A3R3KT000 0603 LF Multi-Layer Inductor MLF1608A4R7KT 0603 LF Multi-Layer Inductor 0.3×1.5×2.5T P type AIR-CORE COIL with pin“E" L2,L21,L24,L25,L26,L27, L33 0.3×1.5×3.5T P Type AIR-CORE COIL with pin “E"...
Page 30
S1 Service manual S1 Assembly parts BOM Version:1.0 Part No. Material Specification Quanitty Description Model TH308K(D02) half F02308-032 products Assembly:Plastic parts P01308-027 Front cabinet P10308-009 Back cabinet Back cabinet P14308-009 accessories P09308-010 Battery cover P21308-004 Earphone jack cover P15308-004 Button...
Page 31
Navy blue, white characters Oversea use T15308-036 "S1" Navy blue, white characters Oversea use T11308-000 Unit number Series number T12308-008 Frequency mark 31×27mm S1 (D02) Packing parts BOM Version: Part No. Item Specification Quantity Description Model External mark on the "anti-counterfeiting T13307-001 mark"...
S1 Service manual Packing 15.PROTECTION BAG (H25-0085-04) 14.PACKING FIXTURE 21.BELT HOOK (H12-3037-02) (J29-0624-03) 16.PROTECTION BAG ANT.WHIP ANTENN A (H25-2012-04) (T90-0694-15):M (T90-0684-05);M4 17.ITEM CARTON CASE (H52-1522-02) 3. CAP G. SCREW SET (B09-0351-03) (N99-0396-05) 20.SP/MIC HOLDER (J21-4493-04)
S1 Service manual Adjustment Required test Equipment 1.Stability power supply 1.The supply voltage can be changed between 3.7V and 68V, and the current is 3A or more. 2.The standard voltage is 4.0V 2.DC Ammeter 1. Class 1 ammeter (17ranges and other features).
Page 39
S1 Service manual 10.Spectrum Analyzer 1.Measuring range:DC to 1GHz or more. 11.Standard Signal Generator (SSG) 1. Maximum frequency:500MHz or more. 2. Output:-133dBm/0.05µV to 7dBm/501mV 3. Output resistance:50Ω 12.Tracking Generator 1. Center frequency:50KHz to 500MHz 2. Frequency Deviation:±35MHz 3. Output voltage:100mV or more 13.Dummy Load...
Page 40
S1 Service manual Note:Supply power from an external power supply (Relay terminal :+ Jig <chassis> :-) Use the S-1 programming software for adjustment the following item in the PC mode Squelch Level, Transmit frequency, DQT balance, RF power, QT deviation,...
Page 41
S1 Service manual Test Terminal Part Method Equipme 1 . Band 1) CH:RX center Adjust the frequency the adjustment of PMR446 pass-filter 2)Tra generator output generator so that it becomes the version is the same as -40dBm Spectrum spectrum waveform...
Page 42
S1 Service manual 1)CH: TX center Modulation Analyzer Antenna ±100Hz :±2.4KHz(窄) Maximum or linear detector Speaker adjust to 1KHz/120mV (LPF:15KHz) ±4.2KHz(wide) PTT: ON Oscilloscope Wide check Audio generator peak 、 Audio voltmeter whichever maximum) 1)CH: TX Centre check ±2.2KHz~ SENS...