Related Manuals for FIBRO 2480.00.91.42
Summary of Contents for FIBRO 2480.00.91.42
- Page 1 OPERATING INSTRUCTIONS WPM GATEWAY IOT 2480.00.91.42 Operating instructions WPM Gateway IoT...
- Page 2 Internet: www.fibro.de © All rights to this document are subject to copyright of the author. Without the prior written permission of FIBRO GMBH, this document must not be copied or reproduced, either in full or in part. The instructions are intended only for the operator of the described IoT device only...
-
Page 3: Table Of Contents
Contents Introduction ..............5 Intended use . - Page 4 Data holder ..............31 7.4.1 Data holder –...
-
Page 5: Introduction
Introduction INTRODUCTION Read through these instructions carefully before use and store them. These instructions contain the following important information on the product: • Proper use • Safety • Mounting • • Maintenance • Disposal Proper use also involves • Reading these instructions •... -
Page 6: Disclaimer Of Liability
FIBRO GMBH assumes no liability for damage to facilities and systems near the product caused by a defect in the product or an error in these instructions. FIBRO GMBH is not responsible for the violation of patents and/or the rights of third parties out- side of the Federal Republic of Germany. -
Page 7: Autor's Rights
These instructions may be reprinted only with written approval from FIBRO GMBH. The technical state at the time of the delivery of the product WPM Gateway and the associated instructions shall be decisive if no other information is provided. -
Page 8: Safety
Safety SAFETY Safety instructions These instructions contain safety notices intended to draw attention to possible dangers that should be observed to prevent injury. The pertinent text describes • the type of danger • the source of danger • the options for preventing injuries •... -
Page 9: Protective Measures
FIBRO GMBH must access the network of the Gateway. In order to ensure that the service employee from FIBRO GMBH cannot access the rest of the company network, the Gateway should be disconnected from the network in this case and direct access should be established via network cable from the service employee's notebook to the Gateway. -
Page 10: Product Description
Product description PRODUCT DESCRIPTION Supplied components The product consists of the components • WPM Gateway – IoT device – Power supply unit – WPM software • LAN cable • Quick Start Guide Properties Product features The product WPM Gateway is an IoT device. The IoT device has the WPM software installed, which only works in conjunction with the asso- ciated components. -
Page 11: Interfaces And Led Indicators
Product description Interfaces and LED indicators Fig. 3-1 Interfaces and LED indicators HDMI output USB connectors Antenna Status of the fieldbus Status of the fieldbus Status of the fieldbus USB connectors LAN connection EtherCAT or Profinet Connector 10 EtherCAT output 11 Power connection 11/76 Operating instructions WPM Gateway IoT... -
Page 12: Voltage Supply
Product description Voltage supply The IoT device must be supplied with a voltage of 24 VDC by a suitable power supply unit. 0 VDC Power supply 24 VDC Power supply Functional earthing Inputs and outputs Connector for digital inputs and digital outputs The IoT device has digital inputs and digital outputs for connecting additional components. -
Page 13: System Requirements
Product description Pin assignment of the digital inputs and digital outputs A label is attached to the IoT device with the Connection diagram of the digital inputs and digital outputs. ISO-0V OUT0 OUT1 OUT2 OUT3 +24 VDC ISO-0V +24 VDC 4DI4D0 Fig. -
Page 14: Licensing
Product description Licensing WPM is subject to a license agreement with FIBRO GMBH. The system will not function until a valid license has been stored by an Administrator in the WPM software of the WPM Gateway. To apply for a license and enter the license key, see the section Applying for a New License in chapter 9.1.1 "License and license key"... -
Page 15: Functions In Professional Mode
Product description 3.8.2 Functions in Professional mode In addition to the functions in Basic mode, the following additional functions are available inPro- fessional mode: 1) Configure the data holder 2) Configure the data holder tool screen 3) Update the data holder firmware 4) Assign the data holder sensor 5) Configure the sensor 6) Reset the sensor to factory settings... -
Page 16: Assembly
Assembly ASSEMBLY The installation of the IoT device is described in separate installation instructions. • 2.7551.00.1220. Installation instructions for the WPM Gateway IoT Device The information in these installation instructions must be observed during installation. The selection of a suitable installation site is the responsibility of the operator. 16/76 Operating instructions WPM Gateway IoT... -
Page 17: Commissioning
Commissioning COMMISSIONING Initial commissioning 5.1.1 Network settings As default, the WPM Gateway is preset with the static IP address 10.10.10.10 . This IP address can be changed by a network Administrator when integrating the WPM Gateway into the com- pany IT infrastructure. To be able to access the WPM Gateway, the PC with which access is to be made must be man- ually set to a fixed IP address. - Page 18 Commissioning Fig. 5-1 Setting a fixed IP address on the PC 18/76 Operating instructions WPM Gateway IoT...
-
Page 19: Commissioning The Wpm Gateway
Commissioning 5.1.2 Commissioning the WPM Gateway After the network settings have been set up on the PC, the WPM Gateway can be put into op- eration. 1) Connect the WPM Gateway to the power supply via the power supply unit. 2) Connect the WPM Gateway to the PC via a LAN cable. -
Page 20: Setting The Time
Commissioning 5.1.3 Setting the time If the WPM Gateway is not connected to the internet or cannot obtain the time via NTP, it must be ensured that the current time is set. For this purpose, the appropriate setting can be made in the Admin Panel. •... -
Page 21: Network Connection
Commissioning Network connection Company network/IP settings The Admin Panel can be used to configure the WPM Gateway for the company network or to adjust the IP settings. • Open the Admin Panel at http://10.10.10.10:8080 in the browser. • The first time you log in, use the username admin and the password wpmg8way. •... - Page 22 Commissioning Obtain an IP address • Use the Networking button to open the window. • For IPv4 and IPv6, specify the desired IP addresses or let the WPM Gateway obtain an IP address from your network via DHCP. Fig. 5-5 Obtain an IP address After that, the WPM Gateway can be disconnected from the computer and connected to the in- frastructure.
-
Page 23: Netfield Device Manager
Commissioning 5.2.1 NetFIELD Device Manager The Device Manger is an interactive web front-end for the administration of the IoT device. Normally no settings for the operation of the WPM Gateway have to be configured in the net- FIELD Device Manager. A manual for the netFIELD Device Manager can be obtained from the manufacturer of the WPM Gateway. -
Page 24: User Management Configuration
User management configuration USER MANAGEMENT CONFIGURATION Only users with the Administrator authorisation level can create additional users, edit existing users, or delete existing users. Create users 1) Open the User administration menu. 2) Press the Create User button. 3) Fill in the fields. –... - Page 25 User management configuration Fields Name Meaning E-mail address of the user. This is used to log the user into the WPM Gateway Email and for email notifications. The user's password for logging into the WPM Gateway (minimum length 8 Password characters) .
-
Page 26: Editing A User
User management configuration Editing a user 1) Open the User administration menu. 2) Press the Edit button. 3) Edit fields. 4) Save the changes by clicking the Save button. – The display then jumps back to the user administration menu. Fig. -
Page 27: Changing A User Password
If the access data of the WPM Gateway Administrator is no longer available, a reset key must be requested from FIBRO GMBH (see Chapter9.6 "Reset Administrator password" on page 64). 1) Log in to the WPM Gateway as a user with your own password. -
Page 28: Using The Wpm Gateway
Using the WPM Gateway USING THE WPM GATEWAY WPM Gateway – Login If the WPM Gateway is set up and the URL to the WPM Gateway is called in the web browser at http://GATEWAY-IP-ADDRESS, the Login page appears. 1) Fill in the fields. –... -
Page 29: Wpm Gateway - Display Information
Using the WPM Gateway WPM Gateway – Display information Accessing the web interface via HTTPS The WPM Gateway supports a secured connection via HTTPS using a self-signed SSL certifi- cate created by the WPM software. The SSL root certificate rootCA.crt can be downloaded via the Downloads button. After the download, the certificate must be stored in the web browser as a trusted certificate. -
Page 30: Main Menu
Using the WPM Gateway Main menu After successfully logging into the WPM Gateway, information on data holders, sensors, users, etc. can be viewed and configured according to the authorisation level of the logged-in user. For information on the scope of functions per authorisation level, see Chapter 3.8 "Operating modes and functions"... -
Page 31: Data Holder
Using the WPM Gateway Data holder 7.4.1 Data holder – Overview When the Data holder menu is opened, a list of all data holders known to the system is dis- played. In the top area, the list can be searched by data holder name and filtered based on the alarm states of the data holders. - Page 32 Using the WPM Gateway Symbol Meaning Signal strength of the data holder. See Network signal strength status. Data holder alarm status: All sensors of the data holder comply with the respective limit values. A warning was triggered for at least one sensor of the data holder due to a limit value violation.
-
Page 33: Data Holder - Details
Using the WPM Gateway 7.4.2 Data holder – Details 7.4.2.1 Data holder – Assigned sensors Display sensors assigned to a data holder The Data holder menu shows an overview of all sensors assigned to the data holder. In the top area, the list can be searched by the name and serial number of a sensor via a search field, and can be filtered based on the alarm states of the sensors. - Page 34 Using the WPM Gateway Symbol Meaning By clicking on the check box, the sensor can be either selected or deselected. All selected non-transmitting sensors are removed from the data holder. Sensor alarm status: The measured values of the sensor comply with all limit values. The measured values of the sensor trigger a warning due to a limit value vio- lation.
- Page 35 Using the WPM Gateway Messages In the Sensor view of a data holder, various messages can be displayed depending on the status of the data holder. The data holder configuration has not been updated. The current data holder configuration is no longer up-to-date. Click on "OK"...
- Page 36 Using the WPM Gateway The data holder configuration contains inactive sensors. The data holder configuration contains inactive sensors, the problem can be solved by an administrator. This message is displayed when sensors are assigned to the data holder, but no data has yet been received from them.
- Page 37 Using the WPM Gateway 7.4.2.2 Data holder – Sensor readings diagram view The diagram view for a data holder shows a sensor’s measured values for pressure and tem- perature over time. In the top area, the time period of the area displayed, as well as the refresh rate for the diagram, can be set.
- Page 38 Using the WPM Gateway Displayed limit values per sensor Symbol Meaning Temperature limit values: Temperature limit value is adhered to. Temperature limit value has been exceeded and a warning has been trig- gered. Temperature limit has been exceeded and an alarm has been triggered. Voltage limit values: Voltage limit value is adhered to.
- Page 39 Using the WPM Gateway 7.4.2.4 Data holder – Positioning of the sensors Positioning of the sensors with the help of the tool screen For a data holder, a tool screen can be uploaded for the top and bottom side, on which the indi- vidual sensors can be positioned.
- Page 40 Using the WPM Gateway Symbol Meaning Sensor not selected. Position of the sensor in the tool screen as relative (x,y) coordinates, each in (50,50) the value range between 0...100. Note: When a sensor is placed on the bottom or top of a tool, it is initially dis- played in the centre.
- Page 41 Using the WPM Gateway 7.4.2.5 Data holder – Current parameters Current parameters of a data holder This view shows the currently configured parameters of a data holder. Open view: Main menu => Data holder => => Configuration Fig. 7-9 Current parameters of a data holder Fields Name Meaning...
-
Page 42: Data Holder - Sensors - Details
Using the WPM Gateway 7.4.3 Data holder – Sensors – Details All sensors assigned to a data holder are listed in the Data holder menu. For additional informa- tion, see Chapter 7.4.2.1 "Data holder – Assigned sensors" on page 33. Open view: Main menu =>... - Page 43 Using the WPM Gateway 7.4.3.2 Current parameters of a sensor Current parameters of a sensor In this view, the currently set parameters of a sensor are displayed. Open view: Main menu => Data holder => => Sensor => => Configuration Fig.
-
Page 44: Free Sensors - Overview
Using the WPM Gateway Name Meaning Reset the configuration of the sensor to the factory settings. The assignment to a data holder is also cancelled. Delete all measurement data of the sensor for the currently assigned data holder. Free sensors – Overview Free sensors are all sensors that are not currently assigned to a data holder. -
Page 45: Current Activities
Using the WPM Gateway Current activities This view lists all activities currently performed via Bluetooth. These include: • Activation or deactivation of a data holder. • Activation or deactivation of a sensor. • Reading out and configuring a data holder. •... -
Page 46: Export Diagram Data
Using the WPM Gateway Export diagram data Export diagram data as a CSV file The measured values of data holders and sensors shown in the diagrams can be exported as a CSV file. Open view: Main menu => Data holder or sensor => =>... -
Page 47: Set Up Wpm Gateway
Set up WPM Gateway SET UP WPM GATEWAY Data holder – Changing parameters In the Configuration view of a data holder, the individual parameters of a data holder can be changed. Open view: Main menu => Data holder => => Configuration Fig. -
Page 48: Data Holder - Assigning Free Sensors
Set up WPM Gateway Data holder – Assigning free sensors In the Sensors view of a data holder, free sensors can be assigned to a data holder. Open view: Main menu => Data holder => => Sensors Fig. 8-2 Data holder – Assigning free sensors By clicking the button, the dialogue listing all free sensors with their current measured val- ues is displayed. - Page 49 Set up WPM Gateway Fig. 8-4 Data holder – Parametrising an assigned sensor Click the Save button to save the sensor parameters. The dialogue is closed and the sensor ap- pears in the Sensors view of the data holder. 49/76 Operating instructions WPM Gateway IoT...
-
Page 50: Data Holder - Tool Screen Assignment
Set up WPM Gateway Data holder – Tool screen assignment In the Tool screen view of a data holder, the positioning of the sensors on the tool can be dis- played. A data holder can be assigned a tool screen for both the top and bottom side. Open view: Main menu =>... -
Page 51: Positioning Sensors On The Tool Screen
Set up WPM Gateway Positioning sensors on the tool screen Before sensors can be positioned on the tool screen, a tool screen must be assigned to the data holder for the respective top or bottom side (see Chapter 8.3 "Data holder – Tool screen assign- ment"... -
Page 52: Sensors - Changing Parameters
Set up WPM Gateway Sensors – Changing parameters In the Configuration view of a sensor, the individual parameters of a sensor can be changed. Open view: Main menu => Data holder => => Sensors => => Configuration Fig. 8-7 Sensors – Changing parameters Change sensor name 1) Enter a new sensor name in the Sensor name input field (maximum 15 characters). - Page 53 Set up WPM Gateway Sensor – Resetting to factory settings The respective sensor can be reset to its factory settings. This means that the sensor parame- ters are reset to the default values and that the assignment to the data holder is lost. Default values of the sensors (factory setting) •...
-
Page 54: Wpm Gateway Administration
WPM Gateway Administration WPM GATEWAY ADMINISTRATION WPM Gateway Settings In the Gateway view, WPM Gateway general settings can be configured, the license for using the WPM Gateway can be managed and the WPM Gateway software can be updated. Open view: Main menu => Administration => Gateway Fig. -
Page 55: License And License Key
1) Click the Request license button. 2) Follow the link in the dialogue that appears. – A new license key will be sent from FIBRO GMBH. 3) Enter the new license key in the License key input field. 4) Click the Save license key button. -
Page 56: Managing Email Settings
WPM Gateway Administration Managing email settings If limit value violations occur, which subsequently trigger a warning or an alarm, a notification via email can be set up for this. Open view: Main menu => Administration => Email Fig. 9-2 Managing email settings Mail server To send emails, a mail server must be entered on the Gateway. - Page 57 WPM Gateway Administration Mail delivery limit The mail delivery limits allow you to restrict the number of notifications for prolonged limit value violations. • Allow new warning notification after X days/hours/minutes. – If a limit value violation occurs at a sensor, which triggers a warning, the next notification for this sensor will only be sent again after the selected time period if the limit value vio- lation has not yet been rectified.
-
Page 58: Setting The Filter For Press Mode
WPM Gateway Administration Setting the filter for Press mode Various threshold values can be set to compensate for short-term fluctuations in the sensor val- ues. In this case, an alarm or warning is only issued at the outputs of the WPM Gateway when the threshold values have been exceeded. -
Page 59: Connecting Press Control
Downloads button. • For EtherCAT, download the file Fieldbus_EtherCAT_Gateway.xml • For Profinet, download the file Fieldbus_Profinet_Gateway.xml. For the functional scope of the EtherCAT or Profinet application, contact a representative at FIBRO GMBH. 59/76 Operating instructions WPM Gateway IoT... -
Page 60: Connection With An Opc Ua Client
WPM Gateway Administration 9.4.2 Connection with an OPC UA Client Connect an OPC UA Client with the WPM Gateway On the WPM Gateway, an OPC UA server is executed, which supports the data exchange with OPC UA clients. Open view: Main menu => Administration => Fieldbus Fig. - Page 61 WPM Gateway Administration Download the OPC UA certificate for the WPM Gateway The WPM Gateway provides a self-signed certificate for secure communication via OPC UA. You can download the SSL Root certificate opc_ua.crt.der via the Downloads button. For certificate storage in the OPC UA Client, see the OPC UA Client documentation. 61/76 Operating instructions WPM Gateway IoT...
-
Page 62: Setting Up Mqtt Proxy
WPM Gateway Administration 9.4.3 Setting up MQTT proxy The WPM Gateway uses MQTT for inter-service communication. By setting an MQTT proxy, the MQTT events can be forwarded to an external MQTT broker. The description of the MQTT Topics can be found under the link WPM Gateway MQTT Topics . Open view: Main menu =>... -
Page 63: Wpm Gateway - Operating Statistics
WPM Gateway Administration WPM Gateway – Operating statistics The software installed on the WPM Gateway consists of various services and is based on Dock- er container virtualisation. In this view, various statistics on CPU usage, memory usage and net- work traffic of the individual services, as well as for the WPM Gateway itself can be viewed. The statistics are used by the support team to help clarify problems. -
Page 64: Reset Administrator Password
Reset Administrator password If the access data of the WPM Gateway Administrator is no longer available, a reset key must FIBRO GMBH be requested. 1) Log into the web browser with the email address of the WPM Gateway Administrator. –... -
Page 65: Maintenance
Maintenance MAINTENANCE 10.1 WPM Gateway – Update A WPM Gateway update can be performed by an Administrator. Open view: Main menu => Administration => Gateway => Gateway update Fig. 10-1 WPM Gateway Update 1) WPM Gateway updates are each provided as a TAR file. 2) Drag &... -
Page 66: Data Holder - Updating Firmware
Maintenance 10.2 Data holder – Updating firmware A data holder firmware update can be performed by a user with the authorisation level Professional or Administrator. View information about the installed firmware on the data holder and update the firmware. Open view: Main menu => Data holder => =>... -
Page 67: Sensor - Updating Firmware
Maintenance 10.3 Sensor – Updating firmware A sensor firmware update can be performed by a user with the authorisation level Professional or Administrator. Open view: Main menu => Data holder => => Sensors => => Firmware Fig. 10-3 Sensor firmware update 1) Drag and drop the firmware file to the firmware upload area to updating. -
Page 68: Changing The Battery
Maintenance 10.4 Changing the battery The products of the WPM series from FIBRO GMBH are equipped with batteries. If the WPM Monitor indicates a lower battery voltage for a WPM component, the battery needs to be replaced. The documentation for the WPM component concerned describes how to replace batteries. -
Page 69: Disposal
Disposal DISPOSAL 11.1 Disposing of the battery NOTICE Dispose of the battery properly The battery consists of lithium metal cells. Lithium is a valuable raw material and a hazardous material. Improper disposal may cause environmental damage and may be prosecuted. ... -
Page 70: Indexes
Indexes INDEXES 12.1 Third-party products The product contains no components from third-party companies. 12.2 Glossary Term Explanation Operator Person or organisation that uses the product or system respon- sibly. User Users are generally persons who can use the product. Basic users generally have read access. Basic Additionally, data holders, sensors and press mode may be en- abled/disabled. -
Page 71: Index Of Figures
Indexes 12.3 Index of figures Fig. 3-1 Interfaces and LED indicators Fig. 3-2 Digital inputs/digital outputs Fig. 3-3 Connection diagram for digital inputs/digital outputs Fig. 5-1 Setting a fixed IP address on the PC Fig. 5-2 Commissioning the WPM Gateway Fig. -
Page 72: Index Of Tables
Indexes Fig. 9-6 Setting up MQTT proxy Fig. 9-7 WPM Gateway Operating Statistics Fig. 9-8 Reset Admin password Fig. 10-1 WPM Gateway Update Fig. 10-2 Data holder – Updating firmware Fig. 10-3 Sensor firmware update 12.4 Index of tables Tab. 3-1 Pin assignment digital inputs/digital outputs Tab. -
Page 73: Appendix
Appendix APPENDIX 13.1 Personal notes ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................73/76 Operating instructions WPM Gateway IoT... -
Page 74: Index
Appendix INDEX Digital inputs/outputs 12 Connection diagram 13 Access Function 13 Company networks 9 Disclaimer of liability 6 Protective measures 9 Display unauthorised 9 Data holder 14 Access data Free sensors 14 Administrator 64 Sensor 14 Activation Telegraph statistics 15 Configuration MQTT proxy 15 User Administration 14 Data holder 14... - Page 75 Appendix OPC UA Versions 29 Client 60 60 60 View Docker statistics 15 Connection 60 OPC_UA_Gateway.xml 60 Server 60 Web browser 13 Operating instructions 29 Web interface 12 Operator 70 WPM component 68 WPM data holder 5 10 Password WPM Gateway Administrator 64 Administrator 19 WPM Gateway license 19 change 14...
- Page 76 More information at www.fibro.de/downloads-springs-gas springs/ FIBRO GMBH THE LÄPPLE GROUP Business Area Standard Parts LÄPPLE AUTOMOTIVE August-Läpple-Weg FIBRO 74855 Hassmersheim FIBRO LÄPPLE TECHNOLOGY Germany LÄPPLE AUS- UND WEITERBILDUNG T +49 6266 73-0 info@fibro.de www.fibro.com...
Need help?
Do you have a question about the 2480.00.91.42 and is the answer not in the manual?
Questions and answers