Table of Contents
Advertisement
RDR6350 Digital Mobile
Two-Way Radio
Communications Systems
Starting and Stopping Scan
Press the programmed Scan button to start or stop the Scan feature or
follow the procedure below:
1. Press
to access the menu, press
P1
Services.
2. Press
or
to navigate to Scan and press
3. Press
or
to navigate to On/Off.
4. Press
or
to select On or Off and press
5. The LED blinks orange and the Scan icon is displayed when scan
is enabled. THE LED turns off and the Scan icon disappears when
Scan is disabled.
Responding to a Scan
During scanning, your radio stops on any channel / group where
activity is detected. After the transmission is over the radio remains
on the active channel for a programmed time period known as "hang
time".
1. Press the {PTT} button during hang time to respond to the call. The
LED lights up red.
2. Release the [PTT] button to listen.
Note: If you do not respond within the hang time period,
the radio continues scanning other channels / groups.
Deleting a Nuisance Channel
If a channel continually generates unwanted calls or noise (termed
a "nuisance" channel), you can temporarily remove the unwanted
channel from the scan list.
Note: This capability does not apply to the channel designated as the
Selected Channel. This feature is not accessible through the menu.
1. When your radio stops on an unwanted or nuisance channel, press
the programmed Nuisance Channel Delete button until you hear a
tone.
2. Release the Nuisance Channel Delete button. The nuisance
channel is deleted.
Restoring a Nuisance Channel To restore the deleted nuisance
channel, power the radio off and back on again or press Stop and Start
to restart a scan via the programmed Scan button.
Keypad Locked and Keypad Unlocked
You can lock your radio's keypad to avoid an inadvertent key press.
You have two options to lock your keypad:
•
Shortcut key: press the programmed keypad lock button to lock
or unlock the keypad.
•
Use keypad to activate the setting:
1. Press
to access the menu
P1
2. Press
or
to navigate to Settings and press
3. Press
or
to navigate to Keypad Lock and press
select.
4. Press
or
to select the appropriate time frame or turn
the keypad lock off, press
or
to navigate to
to select.
P1
to select.
P1
to select.
P1
P1
to confirm.
P1
Copyright © 2020 RCA Communications Systems www.RCACommunicationsSystems.com
INSTRUCTION MANUAL
Setting Alerts/Tones
The Alerts/Tones menu allows you to preset or customize radio's
audible alerts and tones for the following actions listed below. You
can Enable or Disable each one of them individually and/or select
a Vibration option. The settings are radio-wide and affect all radio
operating modes.
1. Press
to access the menu.
P1
2. Press
or
to navigate to Settings and press
3. Press
or
select.
4. You have 4 options, use
press
to confirm or customize additional setting:
P1
•
Standard
•
Vibrate
•
Silence
•
Custom
◊
Notification
◊
Key
◊
Incoming Call
◊
New Message
◊
Talk Permit
◊
Power On
◊
Power Off
Setting Date and Time
This setting allows the user to set or adjust the date and time according
to the preferred time zone.
1. Press
to access the menu.
P1
2. Press
or
to navigate to Settings and press
3. Press
or
to navigate to Date and Time and press
select.
4. Use the
or
to move to the next section.
Setting Screen Saver
This setting allows the user to set a default time interval for the display
screen saver to stay ON after the last action taken by the user.
1. Press
to access the menu.
P1
2. Press
or
to navigate to Settings and press
3. Press
or
to navigate to Screen Saver and press
4. You have below 6 options, press
time frame or turn the screen saver Off, press
•
Off
to
•
5 Sec
•
10 Sec
•
20 Sec
•
30 Sec
•
1 Min
to navigate to Alerts/Tones and press
or
to select the desired setting and
button to adjust the number, use the
or
to select the appropriate
P1
12
to select.
P1
to
P1
to select.
P1
to
P1
button
OK
to select.
P1
to select.
P1
to confirm.
Advertisement
Table of Contents
