Advertisement
Table of Contents
- 1 Step 1: Set up the Feeder
- 2 The #10 Envelopes Go in this Way
- 3 Step 2: Thread the Stamps
- 4 Step 3: Set the Toggle Switch to “L” for Label
- 5 Step 4: Set the Sensor Sensitivity Using the Knob
- 6 Step 5: Adjust the Feeding so the Machine Feeds Envelopes Consistently
- 7 Step 6: the Stamps will be Applied to the Leading Edge of the Envelope
- 8 Step 7: Run a Couple of Pieces and Make Sure Everything Looks Good
- Download this manual
How t
to apply
(These ins
structions do
The 9600
tabber is not
t advertised a
makes the
e stamps end
backward
ds onto anoth
Step 1:
Set up the
e feeder as fo
ollows. Remov
If you are
applying stam
the side g
guide. Cut the
e bottom fron
the feed w
wheels.
stamps
s with th
not apply to
the 9700 tab
as being able t
up upside do
own on your
er roll to mak
ke them come
ve the backst
mps to a #10
envelope you
nt corner off s
he Astro
9600 Ta
bber).
to apply stam
mps. However
mail piece so
o you will nee
e out right.
top from the e
envelope sup
u will need a
spacer such a
so spacer doe
es not ever co
abber
r it can be do
ne. This meth
d to re‐roll th
he roll of stam
pport.
as a ¾" piece
of wood alon
ome into cont
tact with and
hod
mps
ng
ruin
Advertisement
Table of Contents
Related Manuals for ASTRO 9600
Summary of Contents for ASTRO 9600
- Page 1 How t to apply stamps s with th he Astro 9600 Ta abber (These ins structions do not apply to the 9700 tab bber). The 9600 tabber is not t advertised a as being able t to apply stam mps. However r it can be do ne. This meth hod makes the e stamps end up upside do own on your mail piece so o you will nee d to re‐roll th he roll of stam mps backward ds onto anoth er roll to mak ke them come e out right. Step 1: Set up the e feeder as fo ollows. Remov ve the backst top from the e...
- Page 2 The #10 e envelopes go in this way: ...
- Page 3 Step 2: Thread th he stamps. Sin nce this mach hine is not a 9 700 model, d don’t follow t he applying s stamp instruc ctions from the manual. You need thread the backing f following the labeling instr ructions from m the manual. . In these pict tures we used d tabs but jus t pretend tha at they are sta amps. ...
- Page 4 Step 3: Set the to oggle switch to “L” for labe e l. ...
- Page 5 Step 4: Set the se ensor sensitiv ity using the knob on the r right side of t the machine. Refer to the picture below w for the locati on of the sen nsor. Make su re there is a s stamp in fron nt of the sens or and turn t he knob until l the red light f first comes on n. Now make sure that the ere is only bac cking paper b behind the se nsor and turn n the knob unti l the red light t first comes on. Now set t the knob to a a positon that t is ½ way bet tween these t two points. ...
- Page 6 Step 6: The stamp ps will be app plied to the le eading edge o of the envelop pe so set the label position n as shown he ere. Step 7: Run a cou uple of pieces and make su ure everything g looks good. . You should b be able to ap ply stamps no ow. © Clean n Machine Mailing 20 015 ...
Need help?
Do you have a question about the 9600 and is the answer not in the manual?
Questions and answers