Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FCI ASF-0010
Summary of Contents for FCI ASF-0010
- Page 1 WallMount Curve Automatic Faucet ASF-0010 Installation Manual Quality Guarantee *Thank you for choosing the automatic wall mount faucet. Please read the instruction carefully before installation. This manual is for your reference only. P a g e...
-
Page 2: Specifications
Features • Hands free sensor operation. • Strategic location of sensor at tip of spout for instant response time. • Easy installation and low-cost maintenance Specifications Power 6V (4 x Alkaline AA) or 120 V 50 Hz AC 12 – 15 cm Sensing Range 0.05 –... -
Page 3: Before Installation
Before Installation • Observe all local and plumbing codes. • Check the cold and/or hot water supply pressure. o The recommended working pressure range is 20 psi - 70 psi (138 kPa - 551 kPa).If the supply pressure is higher than 80 psi (551 kPa), reduce to within recommended range by using a pressure reducing valve (sold... -
Page 4: Tools You Will Need
• Do not place other devices that use an inverter or infrared sensor near the faucet, as this may cause the faucet to malfunction. • Optional: For hot / cold water installation, mixing valve MV-0001 and two ½’ F to 3/8 F FH-0001FF flex hoses are required. -
Page 5: Parts List
Parts List P a g e... - Page 6 Construction / Installation Diagram Cut 600 mm straight PVC and connect both ends of the straight pipe with two 90 degrees elbow pipe per the dimensions on the right. Cut away a section of the wall and place the PVC assembly above onto the wall.
- Page 7 Cover the PVC with drywall or mortar or tile Assemble the mounting plate and the protrective cover with two M4 cross recess head screws P a g e...
- Page 8 Drill 4 6 mm holes inot the wall. Using 4 6 mm set screws fasten the mounitn plate onto the wall. Cut out a 54 mm diameter hole and cover P a g e...
- Page 9 Using a flat head screwdriver remove the protective cover. Remove the two screws from the cover Install the rubber seal & the flex hose onto the faucet. Fasten the faucet onto the wall and slide the decorative cover towards the wall. P a g e...
- Page 10 Connect the inlet end and faucet fittings of the flex hose to the control box. Dimensions for reference P a g e | 10...
- Page 11 Operations No adjustments are required for most settings. Effective sensor default range is 12 cm. factory setting should be satisfactory for most installations. Place your hands under the faucet. The water will flow for 5 secs within the sensor’s range. When hands are removed water flow should stop.
-
Page 12: Battery Replacement
Battery Replacement Replace battery when RED LED indicator flashes rapidly or when flusher stops functioning. i. Turnoff the water supply. ii. Disconnect the battery box from the sensor. iii. Remove the battery holder iv. Using a Philips screw driver remove the battery cover and the batteries. -
Page 13: Troubleshooting
Troubleshooting 1. LED indicator in the sensor is red. i. Battery power is low. Install four (4) new AA sized batteries. 2. Faucet does not function. i. Batteries not installed correctly or depleted. Install four (4) new AA sized batteries. ii. -
Page 14: Care And Cleaning
Care & Cleaning DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean faucet that may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. - Page 15 Resources For Installation guides, visit our resource page through the QR code. Alternatively, you can visit our resource page at https://faucetscanada.ca/resources/ To view more products from Faucets Canada, visit our shop page through the QR code. Alternatively, you can visit our shop page at https://faucetscanada.ca/shop/ Warranty Information...
- Page 16 About us Here at FCi, our main goal is to break the eco- innovation boundary and provide customers with fixtures that save water and deliver reliable sources of sanitation every time. As Canada’s favourite automatic faucet brand, we are proud to say we deliver quality touchless fixtures that perform beyond expectations and exceed design standards.