Related Manuals for QMAXZ Lighting QS Series
Summary of Contents for QMAXZ Lighting QS Series
- Page 1 USER MANUAL ENGLISH Version 3.09 S-series QMAXZ Lighting 2009, © all rights reserved www.qmaxz.com...
- Page 2 QS series manual v3.09 - 1 - QMAXZ © 2009...
-
Page 3: Table Of Contents
10.2 Photometric data Page 27 10.3 Dimensional drawings Page 28 11. DMX Protocol Page 29 11.1 QS250S Page 29 11.2 QS250W Page 32 12. Troubleshooting Page 34 13. Info Page 35 QS series manual v3.09 - 2 - QMAXZ © 2009... -
Page 4: Introduction
For the latest updates of product documentation, please visit the user support area of the QMAXZ website at www.qmaxz.com NOTE: Information and Specifications in this document are subject to change without notice. QMAXZ Lighting assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. 2. UNPACKING... -
Page 5: Rigging The Fixture
10 times the weight of the fixture. To un-mount the brackets turn the twist lock by 90 degrees counter clockwise and release the brackets from the fixture base. QS series manual v3.09 - 4 - QMAXZ © 2009... -
Page 6: Lamp Replacement
QMAXZ fixtures are tested with PHILIPS bulbs. QMAXZ also advises to use the same bulbs for replacement. QMAXZ is not responsible for any damage to the fixture when using other bulbs! QS series manual v3.09 - 5 - QMAXZ © 2009... -
Page 7: Lamp Installation
3. Turn the screws one by one clockwise and/or counter clockwise until the hotspot is in the centre of the beam. If you cannot detect the hotspot, adjust the lamp until the output is evenly spread over the beam and the output is the brightest. QS series manual v3.09 - 6 - QMAXZ © 2009... -
Page 8: Power And Signal Connection
4. Connect the mains power again and turn on the fixture to check proper operation. There is also a fuse on the main PCB board inside the fixture, for how to replace this please contact your dealer. QS series manual v3.09 - 7 - QMAXZ © 2009... -
Page 9: Signal Connection
Do not overload the link. A maximum of 10 devices may be connected on a serial link. Insert a male 120Ω XLR termination plug, in the last fixture. This to avoid signal reflection and interference. DMX Terminator DMX connection panel QS series manual v3.09 - 8 - QMAXZ © 2009... -
Page 10: Fixture Start Up
When no button on the control panel is touched for more then 30 seconds the display will turn off and the menu will go back to the DMX start address, to turn it on simply press a button and repeat the above steps to enter the menu. QS series manual v3.09 - 9 - QMAXZ © 2009... -
Page 11: Function Menu Qs250S
7.2 Function Menu QS250S. QS series manual v3.09 - 10 - QMAXZ © 2009... - Page 12 QS series manual v3.09 - 11 - QMAXZ © 2009...
- Page 13 QS series manual v3.09 - 12 - QMAXZ © 2009...
- Page 14 QS series manual v3.09 - 13 - QMAXZ © 2009...
- Page 15 MENU_13.4 Gobo 1 Gobo 2 [MENU] > [ESC] > [ESC] >store configuration and return Gobo 2 Adjust: to menu 1 Color 1 MENU_13.5 Gobo 2 Color 1 Color 1 Adjust: QS series manual v3.09 - 14 - QMAXZ © 2009...
- Page 16 QS series manual v3.09 - 15 - QMAXZ © 2009...
-
Page 17: Function Menu Qs250W
7.3 Function Menu QS250W. QS series manual v3.09 - 16 - QMAXZ © 2009... - Page 18 [ESC] > no change in setting and return to menu 5 [UP/DOWN] > swop selection MENU_5.2 LAMP mode [MENU] > [ESC] > store configuration and return to Auto On menu 1 DOWN QS series manual v3.09 - 17 - QMAXZ © 2009...
- Page 19 QS series manual v3.09 - 18 - QMAXZ © 2009...
- Page 20 QS series manual v3.09 - 19 - QMAXZ © 2009...
- Page 21 QS series manual v3.09 - 20 - QMAXZ © 2009...
-
Page 22: Menu Functions
CHANNEL LIST Viewing the fixture channel list (for the current Operating mode) and actual receiving DMX values, use [UP] or [DOWN] to scroll the channel list, [MENU] or [ESC] to exit. QS series manual v3.09 - 21 - QMAXZ © 2009... -
Page 23: Rdm Functions
QMAXS QS-series fixtures can be updated by using the USB connection on the back side of the LCD display inside the fixture, for instructions ask your dealer or download the update instructions, QMAXZ update-program and latest software on www.qmaxz.com. QS series manual v3.09 - 22 - QMAXZ © 2009... -
Page 24: Control Channels Dmx
√ √ Yellow √ √ √ √ √ √ √ √ √ √ √ √ CMY speed √ √ √ √ √ √ Zoom √ √ √ √ √ √ QS series manual v3.09 - 23 - QMAXZ © 2009... -
Page 25: Gobo And Gobo Size
QGM11 QGM12 QGM13 8.2 Rotating / Glass Gobos overall size 28mm, image size 21,5mm Standard factory installed: QGG1 QGG2 QGG3 QGG4 QGG5 QGG6 Optional gobo’s: QGG7 QGG8 QGG9 QGG10 QGG11 QS series manual v3.09 - 24 - QMAXZ © 2009... -
Page 26: Gobo Positions
6. Put in a new gobo by sliding it in the pocket on the wheel, and secure it with a drop of glue. 7. Attach the safety cable of the cover again, and put the cover back on, tighten the 4 screws. QS series manual v3.09 - 25 -... -
Page 27: Maintenance
The QMAXZ fixture does not require lubrication under normal circumstances. The slides for the zoom and focus lens cars are lubricated with a long-lasting Teflon-based grease that can be reapplied by you’re dealer. Check mains power plug regularly, for connection and mechanical liability. QS series manual v3.09 - 26 - QMAXZ © 2009... -
Page 28: Qs-Series Technical Data
250° 250° Pan Fine 3,6° 3,6° Tilt Fine 3° 3° Dimensions Fixture 575x474x347 575x474x347 Dimension Carton 648x484x492 648x484x492 Net. Weight 28Kg 28Kg Gross Weight 31Kg 31Kg 10.2 Photometric Data QS250S/QS250W QS series manual v3.09 - 27 - QMAXZ © 2009... -
Page 29: Dimensional Drawings
10.3 Dimensional Drawings QS series manual v3.09 - 28 - QMAXZ © 2009... -
Page 30: Dmx Protocol
Random opening pulse, fast 200-209 Random opening pulse, medium 210-219 Random opening pulse, slow 220-229 Random closing pulse, fast 230-239 Random closing pulse, medium 240-249 Random closing pulse, slow 250-255 Shutter open QS series manual v3.09 - 29 - QMAXZ © 2009... - Page 31 Gobo 4, shake slow -> fast 170-184 Gobo 3, shake slow -> fast 185-199 Gobo 2, shake slow -> fast 200-214 Gobo 1, shake slow -> fast 215-224 Open 225-255 CCW scroll, slow -> fast QS series manual v3.09 - 30 - QMAXZ © 2009...
- Page 32 Pan/tilt movement, blackout 210-239 All function change, blackout 240-255 No blackout Fastest 16BIT PAN/TILT SPEED 10-225 X/Y speed, fast-slow 16BIT 0-255 Pan fine PAN FINE 16BIT 0-255 Tilt fine TILT FINE QS series manual v3.09 - 31 - QMAXZ © 2009...
-
Page 33: Qs250W
Random opening pulse, slow 220-229 Random closing pulse, fast 230-239 Random closing pulse, medium 240-249 Random closing pulse, slow 250-255 Shutter open 8/16BIT 0-255 Pan 540° (128=neutral) 8/16BIT 0-255 Tilt 250° (128=neutral) TILT QS series manual v3.09 - 32 - QMAXZ © 2009... - Page 34 Pan/tilt movement, blackout 210-239 All functions, blackout 240-255 No blackout Fastest PAN/TILT 18BIT SPEED 10-225 Pan/tilt speed, fast -> slow 16BIT 0-255 Pan fine PAN FINE 16BIT 0-255 Tilt fine TILT FINE QS series manual v3.09 - 33 - QMAXZ © 2009...
-
Page 35: Troubleshooting
Disconnect the mains power supply and replace the Lamp has reached the end of his lamp (see chapter 5). lifetime cycle. QS series manual v3.09 - 34 - QMAXZ © 2009... -
Page 36: Info
If there is any doubt of safe operation during the products lifetime please contact your dealer or QMAXZ lighting at all times to check whether it is safe to use the product before operating it. QMAXZ lighting Mr.
Need help?
Do you have a question about the QS Series and is the answer not in the manual?
Questions and answers