Advertisement
Z-Wave Ultra low temperature sensor
PAT14
The Z-Wave Ultra low temperature sensor PAT14 has 2 channel
thermocouple , based on Z-Wave
This device is a security enabled Z-Wave Plus™ product. The
encrypted Z-Wave Plus™ messages support PAT14 to communicate
with other Z-Wave Plus™ products.
PAT14 can be used with Z-Wave™ devices (with Z-Wave™ logo) from
different manufacturers, it can also be included in the Z-Wave™
networks from different manufacturers.
TM
technology.
All mains operated nodes (even from different manufacturers) in the
network act as repeaters to increase the stability and reliability of the Z-
Wave™ network.
The product is supported with Over-the-Air (OTA) feature for firmware
upgrade.
Specification
Rated
RF distance
RF Frequency
RF Maximum Power
Dimension
Location
Operation temperature
Storage Temperature
Humidity
Temperature Detect Range
Sensor type
FCC ID
Specifications are subject to change and improvement without
notice.
1
DC5-24V 6mA
Min. 40M indoor,
100M outdoor line of sight,
868.40 MHz, 869.85 MHz(EU)
908.40 MHz, 916.00 MHz(US)
920.9MHz, 921.7MHz,
923.1MHz(TW/SG/Thai/KR)
+10dBm (Peak), -10dBm
(Average)
47.5 x 39 x16 mm
Indoor use only
-10°C - 40°C
-20°C - 60°C
Up to 85% max
-250 to 300°C
External K/J/T type
thermocouple
(depend on the user choice)
RHHPAT14
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Philio PAT14
Summary of Contents for Philio PAT14
- Page 1 Z-Wave Plus™ messages support PAT14 to communicate Specifications are subject to change and improvement without with other Z-Wave Plus™ products. notice. PAT14 can be used with Z-Wave™ devices (with Z-Wave™ logo) from different manufacturers, it can also be included in the Z-Wave™ networks from different manufacturers.
-
Page 2: Troubleshooting
Add to/Remove from Z-Wave Network There is a button with LED indicator in front of PAT14. It is used to dim on/off the light and carry out the inclusion, exclusion, reset or association of PAT14 from Z-wave controller. When the fist power one, the LED indicator flashes once per second for 30 seconds. -
Page 3: Led Light Indication
Remove 2. Press the button on PAT14 three times within 3 sec- PAT14 just be set to send reports to multi channel associated Z- (Exclusion) onds to enter exclusion mode. Wave™ devices. It supports five association groups with five nodes 3. -
Page 4: Over The Air (Ota) Firmware Update
DEVICE_RESET_LOCALLY_NOTIFICATION. The device support the timing unsolicited report of the status. Group 2, End Point 1 will report ( channel 1) Temperature report: Every 1 hours report once in default. • SENSOR_MULTILEVEL_REPORT_TEMPERATURE It could be changed by setting the configuration NO. 5. Group 3, End Point 2 will report ( channel 2) SENSOR_MULTILEVEL_REPORT_TEMPERATURE Notice: The configuration NO. - Page 5 Name Description Name Description Def. Def. Valid Valid Bit control. Auto Temperaturn auto report time Report 0 : disable. Bit0: reserve. Temperat Default is 5. Tick Interval can Bit1: reserve. ure Time setting by configuration No.4. Bit2: reserve. The interval time for auto report each tick.
-
Page 6: Z-Wave Supported Command Class
They can take this product for Highest granted Security Class Version environmentally safe recycling. Highest granted Security Class Device Reset Locally Philio Technology Corporation 8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City Highest granted Security Class Indicator 24257, Taiwan(R.O.C) w ww.philio-tech.com... -
Page 7: Fcc Interference Statement
FCC Interference Statement Warning Do not dispose of electrical appliances as unsorted municipal waste, This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These use separate collection facilities.
Need help?
Do you have a question about the PAT14 and is the answer not in the manual?
Questions and answers