Page 1
LCD TV SERVICE MANUAL CHASSIS : LP73A MODEL : 22LS4R 22LS4R-TA CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
Page 4
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range This specification is applied to the 19”/ 22” Wide LCD TV used LP73A chassis. 2. Requirement for Test Testing for standard of each part must be followed in below condition.
Page 7
4. Module Specification 4.1. 22” LCD MODULE (LPL LM220WE1-TLA1) Item Typ. Unit Remark Display area 473.76 (H) x 296.1 (V) Outline dimension 493.7 (H) x 320.1 (V) x 16.5 (D) Number of Pixels 1680 (H) x 1050 (V) 1Pixel=3RGB Cells Cell pitch 0.282mm (H) x 0.282mm (V) 1Pixel=3RGB Cells...
ADJUSTMENT INSTRUCTION 1. Application Range This specification sheet is applied to 19”/ 22” LCD TV which is manufactured in TV (or Monitor) Factory or is produced on the basis of this data. filexxx.bin (7) ..OK 2. Specification 1) The adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing.
Page 11
: 78 at MSPG925L) 4) Check whether written EDID data is correct or not. (refer (3) Input signal : (1680 x 1050@60Hz) -> 22LS4R to Product spec). Full white 216/255 gray level (85 IRE, Model : 122, Pattern : 78 at MSPG925L)
Page 12
2) DIGITAL DATA 256Byte 4.11 Option data setting (SVC OSD setting) (1) PAL Model (Change by Suffix)- Tool option 19LS4R-MA 22LS4R-MA 12161(19”) 12162(22”) Resolution Module SCART COMPONENT PC-RGB HDMI - All Data : HEXA Value (2) Area Option S.Am - Changeble Data...
Page 13
5. Adjustment Command (2) Command Set Adjustment contents CMD(hex) ADH(hex) ADL(hex) Details 5.1. Adjustment Commands(LENGTH=84) EEPROM READ 0-Page 0~7F Read 0-Page 80~FF Read Adjustment Contents Description (hex) 1-Page 0~7F Read FACTORY ON Factory mode on 1-Page 80~FF Read FACTORY OFF Factory mode off 2-Page 0~7F Read EEPROM ALL INIT.
TROUBLE SHOOTING 1. No Power (LED indicator off) : [A] Process Fail Check 15V or Check short of Main B/D ST_5V of Power B/D. or Change Power B/D. Pass Fail Fail Check short of Re-soldering or Change Check Output of IC1100, IC1101.
Page 15
2. No RASTER : [B] Process Fail Check LED status Repeat A PROCESS. On Display Unit. Pass Fail Check Panel Link Change Panel Link Cable or Module. Cable or Module. Pass Fail Check Inverter Change Inverter Connector or Inverter. Connector or inverter.
Page 16
3. No RASTER on PC Signal Repeat [A, B] process. Pass Fail Check the input/ Check the J701. output of R735, R736. Pass Check Fail Re-soldering or Change the input/output the defect part. of R128, R131, R136. Pass Fail Check the Re-soldering or change the input/output of IC100.
Page 17
4. No Raster on Component Signal Repeat [A, B] process. Pass Fail Check the input/ Check the J900. output of R901. Pass Check Fail Re-soldering or Change the defect part. the input/output of R125. Pass Fail Check the Re-soldering or change the input/output of IC100.
Page 18
5. No Raster on HDMI Signal Repeat [A, B] process. Pass Fail Re-soldering or change the defect part. Check the input/ Check the X100. output of IC100. Pass Check input source cable and jack. 6. No Raster on AV(Scart in 7.
Page 19
8. No sound Fail Check the input Change the source input. Source. Pass Fail Re-soldering of Change the defect part. Check input/Output Check the X100 of IC100. Pass Fail Check the input/ Re-soldering or Change output of IC500 the defect part. Pass Fail Change Speaker.