CognitiveTPG A798 Setup Manual page 2

Thermal receipt printer

Hide thumbs Also See for A798:

Programming manual (121 pages)

User manual (34 pages)

Setup manual (4 pages)

page of 2

/ 2
Bookmarks

Choose a location for the printer.

Connect the following cables based on your configuration, using a-b below.

��

When using USB (step "b" below),

��

use caution to ensure the USB

cable is connected to the USB

connector on the back left of

the printer and not into the

cash drawer connector that is

��

on the right back of the printer.

Cash drawer (if your installation includes this feature, page 15).

9-pin or 25 pin Serial or USB cable (serial: page 16; USB: page 17).

Connect the power cable (page 18).

Route cables as shown for your setup configuration (page 19).

��

Run a diagnostic test (page 19).

��

All manuals and user guides at all-guides.com

��

Configure the printer if necessary (page 20).

*** A798 – Diagnostics Form ***

Model number

Serial number

��

Boot Firmware

��

Revision

��

CRC

P/N

��

Flash Firmware

��

Revision

��

CRC

��

P/N

��

H/W parameters

Flash Memoriy Size

��

Flash Logos/Fonts

��

Flash User Storage

Flash Journal Size

��

SRAM Size

��

CPU Clock Freq.

��

Head setting

��

Pre-Heating

��

Print Density

��

Max Speed

��

Paper Width

��

Max Power

��

Knife

��

Partial Cut

��

Paper Low Sensor

��

Comm. Interface

��

RX Buffer Size

��

Interface type

Parameters

Baud Rate

��

Data Bits

��

Stop Bit

��

Parity

��

Flow Control

��

Reception Errors

��

USB Driver Type

��

USB Packet w/Error

��

Resident Code Pages

��

A715 CP850 Emulation

Logo(s) defined

User Char(s) defined

��

Journal Unused

Diagnostice

��

To enter Printer Config Menu :

��

1) Flip DIP switch #1 down

2) Reset the printer, while holding

the Paper Feed button down

��

Type of Equipment: Information Technology Equipment – Printer

Model: A798-XXXX-XXXX

Model: A799-XXXX-XXXX (X = any alphanumeric character)

Applicable EU Directives:

2004/108/EC (electromagnetic compatibility directive)

2006/95/EC (low voltage directive for product safety)

Harmonized Standards:

EN 55024 (1998/A1:2001/A2:2003) Information Technology Equipment Immunity Characteristics

EN 55022 (1998/A1:2000/A2:2003) EMC, Class A, Limits and Methods of Measurement of Interference

Characteristics of IT Equipment

IEC 60950-1 (2005) Second Edition - Product Safety Standard.

"TPG IPB, Inc., 950 Danby Road, Ithaca, New York, 14850, declares that the equipment specified

above conforms to the referenced EU Directives and Harmonized Standards."

Randy Bullock, Regulatory Compliance Engineer, CognitiveTPG and TPG IPB

A798-720D-TD00

C073400014

��

� ��

V1.00

� ��

08D3

��

189-7940154A

��

� ��

V1.00

��

� ��

D70C

��

� ��

189-7940155A

��

� ��

��

2 Mbytes

� ��

1152 kbytes

� ��

��

64 kbytes

��

64 kbytes

128 kbytes

� ��

50 MHz

� ��

Disabled

� ��

100%

� �

150 mm/sec

� ��

80 mm

� ��

55 W

� ��

Enabled

� ��

125 steps

� ��

Disabled

� ��

4096

� ��

RS232/USB

115200

� ��

NONE

When the printer is configured for USB, this

DTR/DSR

� ��

Ignore

� �

location will show either: "USB Driver Type:

Printer Class

� �

Native", "USB Driver Type: Printer Class", or "USB

Reject

� ��

Driver: Comm Class".

� ��

437, 850, 852, 857, 858

� ��

860, 863, 865, 866

1252, 862, 737, 874

� ��

Disabled

��

Print Test and Configuration Menu Sample.

��

YES

�

Samples will vary depending on the printer model.

� ��

64 kbytes

��

OFF

� ��

��

� ��

�

��

DECLARATION OF CONFORMITY

Date: Feb 6, 2009

��

Ref #: 189-1300058 Rev C

CognitiveTPG A798 Setup Manual page 2

Related Manuals for CognitiveTPG A798

Related Products for CognitiveTPG A798