Related Manuals for P.A. SRWD-1,2
Summary of Contents for P.A. SRWD-1,2
- Page 1 Stock Reel Winder Model Numbers: SRWD-1,2 F o r m X X X X : R e v i s e d A u g u s t , 2 0 1 5 Page 1...
-
Page 2: Table Of Contents
Table of Contents Introduction ...............................3 General Safety program ............................3 Warning .................................. 3 Warranty Program ..............................4 Receiving and Inspection ............................4 Installation and Assembly ...........................4 Mechanical ................................4 Electrical .................................. 5 Setup and Operation ............................5 Maintenance ..............................7 Mechanical ................................7 Electrical ........................ -
Page 3: Introduction
Introduction Please read this manual thoroughly before installing, operating, applying and maintaining this machinery. Failure to do so may result in serious injury to yourself and/or others. 1.1 General Safety program Accident free operation will result from a well developed, management sponsored and enforced safety program. -
Page 4: Warranty Program
should be inspected and tested no less than weekly to determine the condition of the machine. Necessary maintenance or repair of both shall be performed and completed before the machine is operated. The EMPLOYER shall maintain records of these inspections and the maintenance work performed. Our Company is not responsible to notify the user of this equipment of future changes in State or Federal laws, or construction standards. -
Page 5: Electrical
2.2 Electrical Please see the schematic attached for information regarding tying in the main power. The standard loop control consists of a separate stand with electrical enclosure and touch probes which control the loop height by cycling the Reel's D.C. motor on and off as the material moves up and down between the probes. Please note that the material must be electrically conductive and grounded. - Page 6 application’s combination of: Mode (unwind or rewind) Dancer arm location (right or left side of reel) Coil wrap (under or over) 3.1 Dancer Arm Install the dancer arm toward the side of your choice through the clamp on the dancer arm shaft extending from the front panel of the base cabinet.
-
Page 7: Maintenance
These parameters are all preset to factory defaults and equipment specification and should not be changed before consulting the PA service department. Inside of the KB control are a set of potentiometers at the top of the control. These trim pots are used to adjust the following parameters: JOG –... -
Page 8: Troubleshooting
Troubleshooting Please call P/A Industries for all service related questions at 860-243-8306. 5.1 Overall Model Specifications Model Max Spool Max Strip Shaft Dia. Max Spool Speed DC Drive AC Power Weight Width In(mm) OD in(mm) Range Motor Input lbs(kg) in(mm) (RPM) HP(kW) V/Ph/Hz... - Page 9 F o r m X X X X : R e v i s e d A u g u s t , 2 0 1 5 Page 9...
-
Page 10: Parts List
6.2 Parts List Item# Part# Description 15986 PLATE, MOTOR 12125-04 GEARMOTOR ASSY, 130 VDC, 1/8 HP, 57 RPM 14963-02 SHEAVE, 3L x 3.5 PD x 5/8 BORE,2 13650-16 HOLE PLUG, SQUARE, 2in SQ x 14 Ga 12466-33 FASTENER, NUT, KNURLED, 3/4-10 THD. 16166-02 KEEPER DISC HUB 16167 SHAFT, SLIP CLUTCHSHAFT, SLIP CLUTCH... - Page 11 F o r m X X X X : R e v i s e d A u g u s t , 2 0 1 5 Page 11...
- Page 12 F o r m X X X X : R e v i s e d A u g u s t , 2 0 1 5 Page 12...
Need help?
Do you have a question about the SRWD-1,2 and is the answer not in the manual?
Questions and answers