Black & Decker FSMH1321 Original Instructions Manual page 11

The Delta Head (Fig. D)
This steam mop incorporates a built-in delta head which
enables you to access tight corners and narrow spaces.
Caution! Always wear suitable shoes when accessing the
delta head on your steam mop. Do not wear slippers or
open-toed footwear.
Turn the steam-mop to 'OFF'
u
Wait until the steam-mop cools down (approximately five
u
minutes).
Place the front of your shoe onto the steam head removal
u
tab (12c) and press down gently.
Lift the delta head (12b) up off the steam head (12a)
u
Fit the delta head cleaning pad to the bottom of the delta
u
head.
Note: Remove the cleaning pad before refitting the delta
head to the steam head.
To refit the Delta head, place the yip of the Delta head into
u
the steam head then press down firmly ensuring that the
Delta head clicks into place.
Attaching the hose and accessories to the
hand held steam cleaner (Fig. G - M)
Warning! Inspect the seal between the connection point on
the hand held steam cleaner (5) and the steam hose (16)
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.
Attaching the hose
Press the steam hose release button (16a) on the steam
u
hose (16).
Connect the steam hose (16) to the hand held steam
u
cleaner (5) and release the steam hose release button
(16a) making sure it clicks into place.
Important! Ensure that the steam hose (16) is securely
connected to the hand held steam cleaner (5). If steam
escapes from the joint, the hose is incorrectly fitted. Switch off,
allow the unit to cool then remove and refit the hose.
Attaching accessories (Fig H)
Align the lugs on the steam nozzle (17) with the recesses
u
on the accessory.
Press the accessory onto the steam nozzle (17) and twist
u
anti-clockwise until the accessory clicks into place.
Important! All accessories, apart from the SteaMitt
which has its own hose and connector (25), must be attached
to the steam hose (16) for use.
Removing the hose and accessories
Warning! The steam hose (16), Steam nozzle (17) and
accessories become hot during use. Allow the unit and all
accessories to cool before attempting to remove.
(Original instructions)
Removing an accessory
Twist the accessory clockwise then pull away from the
u
hose (16).
Removing the hose
Press the steam hose release button (16a) on the steam
u
hose (16) and pull away from the hand held steam unit.
SteaMitt
Your BLACK+DECKER
sanitising and cleaning tiles, work tops, kitchen surfaces and
bathroom surfaces. This appliance is intended for indoor
household use only.
Attaching the SteaMitt
steam unit
Warning! Inspect the seal on the steam nozzle and hose
before each use. If the seal is missing or damaged then
please contact your nearest authorised repair agent.
Do not use the appliance. Inspect the seal on the SteaMitt
and hose If the seal is missing, damaged or any steam
is escaping then please contact your nearest authorised
repair agent. Do not use the appliance. Ensure there is no
blockage or impedence in the SteaMitt
hose. If any are detected then please contact your nearest
authorised repair agent. Do not use the appliance.
Fitting a cleaning pad to the
Warning! Ensure there is no blockage or impedence in
the steam release vents If any are detected then please
contact your nearest authorised repair agent. Do not use the
appliance.
Fit the cleaning pad (26) to the SteaMitt
u
attaching the 'loop' velcro strips (26a) on the upper side
of the cleaning pad, to the 'hook' velcro pads (24a) on the
underside of the SteaMitt
Warning! The SteaMitt
cleaning pad.
Note: The SteaMitt
of varying thickness. Scouring pad (for use on tough stains
and non delicate surfaces), Bathroom pad (for use on taps
and other moulded bathroom surfaces), Standard pad (for use
on all larger surfaces) and Polishing pad (for use on delicate
surfaces).
(24)
TM @
Warning! Always use the SteaMitt
figure M, with your hand inside the protective glove.
Warning! Never attempt to use the SteaMitt
@
gripping it externally as shown in figure N.
This will result in scalding.
@
Warning! Avoid using the SteaMitt
as shown in figure O.
TM
SteaMitt has been designed for
TM TM
hose to the hand held
TM
SteaMitt
(24). Press down firmly.
TM
should not be used without fitting a
TM
accommodates 4 types of cleaning pads
TM
ENGLISH
TM
hose or attachment
TM
TM (Fig. J)
(24) by
TM
as shown in
TM
by
TM
in tight corners
TM
11