Mindman MP30 Series Quick Start Manual

MINDMAN INDUSTRIAL CO., LTD.
For your safety, please read the following before using.
Do not use corrosive or flammable gas or liquid with this product.
1
2 Please use within the operating pressure range. Do not apply pressure beyond recommended maximum pressure, permanent
damage to the pressure sensor may occur.
3 Do not drop, hit or allow excessive shock. Even if switch body appears undamaged, internal components may be broken and
can cause malfunction.
Turn power off before connecting wiring. Wrong wiring or short circuit will damage and/or cause malfunction.
4
5 Do not use in environment containing steam or oil vapor.
This product is not explosion-proof rated. Do not use in atmosphere containing flammable or explosive gases.
6
Wiring for pressure sensor should avoid power source line and high voltage line. If use in the same circuit, noise may cause
7
malfunction.
MP30C-

SPECIFICATIONS

(Compound)
Rated pressure range -100.0 ~ 100.0kPa
Setting pressure range
-100.0 ~ 100.0kPa
Withstand pressure
Fluid
kPa
MPa
kgf/cm
2
Set pressure bar
resolution
psi
inH g
mm H g
mmH O
2
Power supply voltage
Current consumption
Switch output
Repeatability(Switch output)
Hysteresis mode
Hysteresis
Window comparator mode
Response time
Output short circuit protection
Display
Indicator accuracy
Indicator
Output voltage: 1 to 5V ± 5% F.S.

Analog output

(within rated pressure range)
*(Only type MP30 -01- MP30 -03-
, )
Linearity: ± 1 % F.S.
Enclosure
Ambient temp. range
Ambient humidity range
Environment Withstand voltage
Insulation resistance
Vibration
Total amplitude 1.5mm, 10Hz-55Hz-10Hz scan for 1 minute, two hours each direction of X, Y and Z
Shock
Temperature characteristic
Port size
Lead wire
Weight
PR-0069D 2021/07 Printing We reserve the right to change the specification without prior notice.
- MP30V- -
(Vacuum)
0.0 ~ - 101.3kPa
10.0 ~ - 101.3kPa
300kPa
Filtered Air, Non-corrosive/ Non-flammable gas es
0.1
-
0.001
0.001
0 .01
0.1
1
0.1
12 to 24V DC ±10%, Ripple (P-P) 10% or less
≦ 60mA
NPN: open collector 2 outputs PNP: open collector 2 outputs
Max. load current: 100mA Max. load current: 100mA
Max. supply voltage: 30V DC Max. supply voltage: 24V DC
Residual voltage: ≦ 1V Residual voltage: ≦ 1V
±0.2% F.S. ±1digit
Adjustable
Fixed (3 digits)
≦ 2.5ms (chattering- proof function: 24ms, 192ms and 768ms selections)
Yes
3 ½ digit, 7 segment LED display ( Red ) ( Sampling rate : 5 times / sec. )
±2% F.S. ±1 digit (Ambient temperature: 25 ±3°C)
Green Indicator : OUT1 & Red Indicator : OUT2
Output voltage: 1 to 5V ±2.5% F.S.
(within rated pressure range)
Linearity: ±1% F.S.
IP40
Operation: 0 ~ 50°C, Storage: -20 ~ 60°C (No condensation or freezing)
Operation/Storage: 35 ~ 85% RH (No condensation)
1000V AC in 1-min (between case and lead wire)
50M Ω (at 500V DC, between case and lead wire)
980m/s (100G), 3 times each in direction of X, Y and Z
2
±2% F.S. of detected pressure (25°C) at temp. Range of 0~50°C
F1:R1/8", M5 ; F2:NPT1/8", M5 ; F3: G1/8"(BSPP), M5
Ø4 Oil-resistance cable ( PVC ) - 26 AWG ( 0.15 mm ) - 5 cores ( MP30 □ - 01 / 03 ) ;
2
Ø4 Oil-resistance cable ( PVC ) - 26 AWG ( 0.15 mm 2 ) - 4 cores ( MP30 □ - 02 / 04 )
Approx. 67g (with 2 meter lead wire), Approx. 35g (with M8 4Pin male connector )

ORDERING INFORMATION

MP30P- -
(Positive)

OUTPUT CIRCUIT WIRING DIAGRAMS

0.000 ~ 1.000MPa
-0. 1 00 ~ 1.000MPa
MP30
1.5MPa
NPN output & Analog output
-
0.001
0 .01
0 .01
0.1
-
-
MP30
-
PNP output & Analog output

PANEL DESCRIPTION

( ) Button
Use the( ) button to change
setting mode and pre-set
desired value.
( ) Button 3 ½ Digit LED Display
Use the( ) button to change Display the measured
setting mode and pre-set pressure value. each setting
desired value. mode and error code.

DIMENSIONS

M P 3 0 C - 0 1 - F 1 -
Pressure Range Pressure Port
C：Compound (-100.0~100.0kPa) F1：R1/8", M5
V：Vacuum (10.0~-101.3kPa) F2：NPT1/8", M5
P：Positive (-0.100~1.000MPa) F3：G1/8"(BSPP), M5
Output Specifications Cable Length/Connector
01：2 NPN output & 1 Analog output Blank：With 2meter cable
02：2 NPN output QD：With M8 4Pin male connector
03：2 PNP output & 1 Analog output *(Only type MP30 -02-
04：2 PNP output
- 01- - MP30
NPN output
DC(+) (Brown)
1KΩ Analog Output
R
L
(Orange)
R
L
OUT1 (Black)
DC DC
12-24V
OUT2 (White)
DC(–) (Blue)
- 03- - MP30
PNP output
DC(+) (Brown)
1KΩ Analog Output
(Orange)
OUT1 (Black)
DC
R 12-24V
OUT2 (White) L
R
L
DC(–) (Blue)
ANALOG OUTPUT
Switch (OUT1) Switch(OUT 2) Analog output range 1 to 5V, proportional to the pressure range.
Green LED Red LED
(Compound)
Analog output (V)
5
3
1
-100.0
Setting utton
B
(Low)
Change setting mode and
pre-set final desired value.
F1:R1/8", M5
F2:N PT1/8", M5
F3: G1/8"(BSPP), M5
MP30
, MP30 -04- )
- 02- -
DC(+) (Brown)
R
L
R
OUT1 (Black)
L
DC
OUT2 (White)
12-24V
DC(–) (Blue)
- 04- -
DC(+) (Brown)
OUT1 (Black)
OUT2 (White) DC
R
L 12-24V
R
L
DC(–) (Blue)
(Vacuum) (Positive)
Analog output (V) Analog output (V)
5 5
1 1
0.0 100.0 (kPa) 0.0 -101.3 (kPa) 0.000
1.000 (MPa)
(Low) (Low)
(High) (High) (High)
300

QD PINOUT

2 4
1 3
2000
Unit:mm
www.mindman.com.tw