Megger DCM330 User Manual

Megger DCM330 User Manual

Clampmeter
Hide thumbs Also See for DCM330:

Advertisement

Quick Links

DCM330
Clampmeter
User Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DCM330 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Megger DCM330

  • Page 1 DCM330 Clampmeter User Guide...
  • Page 2: Safety Information

    Do not attempt to repair this Clamp Meter. It contains no user-serviceable parts. Repair or serving should only be performed by qualified personal. Cleaning Periodically wipe the case with a dry cloth and detergent do not use abrasives or solvents. www.megger.com DCM330...
  • Page 3 CAT I - Measurement category I: The circuits are not connected to mains. Measurement equipment may be safely connected to circuits at the marked rating or lower. The connection rating is that of the lowest rated component in the measurement circuit. www.megger.com DCM330...
  • Page 4: Operation

    Continue to hold the Volt Finder button. If a voltage of 50 V to 1000 V (50 to 500 Hz) is detected near the jaw ,a continuous tone sounds and the red LED near the jaw illuminates. www.megger.com DCM330...
  • Page 5: Diode / Continuity

    F Do not hold the meter in front of the Resistance Tactile Barrier. Battery Replacement To avoid false readings that could lead to electric shock and injury, replace the battery as soon as the low battery indicator ) appears. www.megger.com DCM330...
  • Page 6: Specifications

    Conductor Size : 16 mm diameter. Pollution degree : EMC : EN 61326-1 Shock vibration : Sinusoidal vibration per MIL-T- 28800E (5 ~ 55 Hz, 3 g maximum). Drop Protection : 1.2 m drop to hardwood on concrete floor. www.megger.com DCM330...
  • Page 7 ±(1.0% + 2 dgt) 200.0 KΩ 2.000 MΩ 20.00 MΩ ±(1.9% + 5 dgt) *1 Overload protection : 600 Vrms Open circuit Voltage : -1.3 V approx. * 1 < 100 dgt rolling. * 2 < 10 dgt rolling. www.megger.com DCM330...
  • Page 8 600 Vrms Continuity : Internal beeper activates if the resistance of the circuit under test is less than 50 Ω. It will then turn off if the resistance is increased beyond 250 Ω. Response time is approximately 0.25~1 sec. www.megger.com DCM330...
  • Page 9: Limited Warranty

    The manufacturer shall not be liable for loss of use of the instrument or other incidental or consequential damages, expenses, or economic loss, or for any claim or claims for such damage, expense or economic loss. Some states or countries laws vary, so the above limitations or exclusions may not apply to you. www.megger.com DCM330...
  • Page 10 5. Decommissioning WEEE Directive The crossed out wheeled bin symbol placed on Megger products is a reminder not to dispose of the product at the end of its life with general waste. Megger is registered in the UK as a Producer of Electrical and Electronic Equipment. The Registration No is WEE/ HE0146QT.
  • Page 11 DCM330...
  • Page 12 Manufacturing sites Megger Limited Megger GmbH Megger USA - Valley Forge Archcliffe Road Weststraße 59 Valley Forge Corporate Center Dover 52074 Aachen 2621 Van Buren Avenue Kent +49 (0) 241 91380 500 Norristown CT17 9EN info@megger.de Pennsylvania, 19403 ENGLAND +44 (0)1 304 502101...

Table of Contents