Advertisement
Quick Links
Advertisement
Related Manuals for WATSON SEVEN
Summary of Contents for WATSON SEVEN
- Page 1 SE V EN /R EL AY WORKB ENC H AS S EMB LY I N STR UC TI O N S V.1.2 6/16 INS-SWORKBENCH...
-
Page 2: Tool Tips
WORKBENCH TYPICAL Support Rails Worksurface(s) Raceway Lid(s) Legs Power Raceway FASTENERS #10-32x⅜” Phillips M6-1.0x12mm ¼-20x⅜” Button 5/16-18x¾ Button ½” Arrow Shank ¾” Keyhole Shank Button Pan Head Screw Head Socket Cap Head Socket Cap Rivet, Nylon Rivet, Nylon Head Socket Cap (121376) Screw (123547) Screw (124755) - Page 3 WORKBENCH BASIC COMPONENTS Worksurface(s) Raceway Lid(s) Power Raceway Support Rail(s) Workbench Spine Screen Legs End Cap Data Plates Extended Connector Control Box Aisle End Screen Seven/Relay Workbench Assembly INS-SWORKBENCH...
- Page 4 Place the control box on the Rail in between the access cutouts. Secure control box in place with M6-1x40mm Phillips Pan Head Machine Screw (125293) and M6-1x12mm Nylock Nut (888152) Plug cords Underside Shown Seven/Relay Workbench Assembly INS-SWORKBENCH...
- Page 5 Maximum segments connected: 12 standard Button Head Socket Cap Screw & M6- power, 6 heavy power. 1.0x12mm Nut (x2 per connection point). Join the Raceways with optional Extended Connector using ¼-20x⅜” Button Head Socket Cap Screw Seven/Relay Workbench Assembly INS-SWORKBENCH...
- Page 6 Connect jumpers to the receptacle blocks. The connectors are keyed for the 4-circuit, 8-wire system. Tampering with, or clipping, the molded pins will result in short circuit and void the Watson warranty. Note — Use the jumper grid to determine the correct length to use.
- Page 7 S pi ne Sc reen ( o p t i o na l) Twist the knockouts to open the holes for the Spine Screen supports. Insert Spine Screen supports into Raceway opening and secure with 5/16-18x¾” screws (x2). Seven/Relay Workbench Assembly INS-SWORKBENCH...
- Page 8 Run the data line and install the telecom plate with panel fasteners to the bottom of the Raceway. Note — Data cutouts are sized to fit keystone-style inserts and are compatible with Leviton, Panduit, and other similar fittings. Seven/Relay Workbench Assembly INS-SWORKBENCH...
- Page 9 E nd C a ps o r Op ti o n al A is le Sc reen Attach optional end caps with M6-1.0 Nut (x4). Attach optional Aisle screens with ¼-20x⅜” screws to the underside of the raceway and panel. Seven/Relay Workbench Assembly INS-SWORKBENCH...
- Page 10 Ca bl e Ma n ag er Attach the cable manager with #8x½” Phillips Pan Head Wood Screw to underside of worksurface. Clip the opposite end to raceway. Clip the desk power cable into the wire manager. Seven/Relay Workbench Assembly INS-SWORKBENCH...
-
Page 11: Wiring Schematic
WARNING: RISK OF FIRE OR ELECTRIC SHOCK. THIS OFFICE FURNISHING SYSTEM MAY BE CONNECTED TO MORE THAN ONE SOURCE OF SUPPLY. ALL SOURCES MUST BE DISCONNECTED PRIOR TO ANY SERVICING. NO SINGLE CIRCUIT MAY BE POWERED BY MORE THAN ONE SOURCE. Seven/Relay Workbench Assembly INS-SWORKBENCH... - Page 12 Not es Seven/Relay Workbench Assembly INS-SWORKBENCH...