Related Manuals for Ecovolt Joule Therm JT6r
Summary of Contents for Ecovolt Joule Therm JT6r
- Page 1 JS10/2 User Manual Aluminum Electric Radiator with Kaolin Ceramic Heat Plates JT6r, JT9r, JT12r, JT15r, JT20r Please read this manual carefully before use...
-
Page 2: Important Safeguards
JS10/2 IMPORTANT SAFEGUARDS When using an electrical appliance, basic safety precautions should always be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING WARNING: To reduce the risk of fire, electrical shock, or injury to person: 1. Connect the appliance to single-phase AC supply of the voltage specified on the rating plate 230V +/- 10% 2. - Page 3 JS10/2 inspect the power cord before installation. 7. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard. 8. Never use an extension cord as this may overheat and may cause a fire.
- Page 4 JS10/2 by a person responsible for their safety. 17. Children should be supervised to ensure that they do not play with the appliance. 18. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
-
Page 5: Installation
JS10/2 FINS POWER SWITCH TEMPERATURE SENSOR CHARACTERISTIC 1. 1 heat setting 2. Over heating protection 3. With digital LCD 4. Room temperature setting 5. Room temperature sensor 6. Digital clock, digital week calendar 7. Multi-running mode: daily program mode, weekly program mode, free use mode, pilot system function 8. - Page 6 JS10/2 A. Refer picture (1) & (2), fix the plastic hooks on the back of radiator by contra rotating knob. B. Refer picture (3) & (4), use screw to fix the hanging rack. C. Refer picture (5) & (6), make sure side A is up & side B is down position for the hanging rack. Do not make hanging rack in wrong direction.
- Page 7 JS10/2 screws. F. Refer picture (8), gently insert the heater body of the bottom to the hanging rack first, then push the heater body to be hooked on the whole hanging rack and fasten the hanging rack with hanging sheathing by screw. INSTRUCTIONS FOR USE Warning：...
- Page 8 JS10/2 Set Temperature Normally, the LCD displays room temperature. If you want to change the set temperature, press buttons, the set temperature will flash. Using button again to increase or decrease the set temperature to the desired one. After 10s of non – use of the keypad the display will revert back to the selected one.
- Page 9 JS10/2 Adjusting the Time and Day Setting To set the time and day with the following steps: (1) Press and hold button for around 3 seconds. The minutes (top left of the display) flashes. Using buttons to change the minutes. (2) Press the button.
- Page 10 JS10/2 Item Range Default Temp. Calibration 0℃ -8℃～+8℃ High Temp. Limit 5℃～ 60℃ 35℃ 5℃～ 60℃ 5℃ Low Temp. Limit 5℃～10℃ Frost Protection 5℃ --: Frost Protection OFF Buzzer Sound 0：OFF 1: ON 1: ON Factory Reset 0; 1( Reset) Note：...
-
Page 11: Group Control
JS10/2 Power on your JS10/2 touch screen controller, the main page will display as shown in figure (2-1). There are five zones, select one of the zones and pair all heaters with the controller. (For ID Paring method please see ID Pairing section in this manual) Once pairing is complete, you can see the current temperature and working mode of each room as shown in figure (2-2). - Page 12 JS10/2 Economy Mode Boost Mode Comfort Mode PRG. Mode 4-1: Group ON/OFF Please press to turn on all heaters, and press to turn off all heaters. 4-2: Mode Select There are totally four modes, which are Comfort mode, Economy Mode, PRG. Mode and Boost Mode, you can group control all heaters’...
-
Page 13: Menu Setting
JS10/2 If you want to stop boost mode during working, please change mode to Economy mode or PRG. Mode. Please notes, if change to Economy mode, it can’t stop boost mode, as all heaters works in comfort mode under boost mode. Menu Setting 5-1: Auto Mode Schedule Pre-set 5-1-1... - Page 14 JS10/2 5-1-3 After the day’s pre-set settings have been completed, and you want other heaters have the same working schedule, simply press COPY as shown in figure (5-1-3). After copying is complete, press COPY again to save, and use CANCEL to return. 5-2: Mode Temperature Pre-set 5-2-1 Press Menu then select...
-
Page 15: Copy Setting
JS10/2 Press Menu then select button to enter Protection Settings page. You can set High Protection temp. & Low Protection temp. by button. Once completed press APPLY to save. Copy Setting JS10/2 with two copy functions, from here you can copy the weekdays and copy the program to all heaters. - Page 16 JS10/2 6-1-3 6-1-4 After coping is completed, please press cancel to return to the main screen. ID Pairing Turn Master controller to zone page and press the zone you are going to pair (Pic.1), then long press the house ICON you are going to pair. For example, to pair the first heater with house 1. Long press this icon , the ID code will show on the screen.
- Page 17 JS10/2 Before Pairing After paring (2) If going to pair with slave thermostat, then turn thermostat to off by press M button , and long press M button, the ID code show on screen. The master controller ID code show as FF FF, After paring success, the master will show “...
-
Page 18: Technical Data
JS10/2 Press button in picture 2-1, then you will enter a Menu page as 7-1. Here you can select the language you like, or can press to page 7-2 to edit date & time. Technical Data Frequency: 868 MHz Channel selection: By programming the thermostat and the receiver. - Page 19 JS10/2 Step3: Mount base plate to wall & connect the ribbon cable Install the base plate to wall tightly with provided screw, then reconnect the ribbon cable and reset the face plate(bottom edge first) Size Front(unit:mm) Mounting Hole (unit:mm) Thickness (unit:mm)
-
Page 20: Maintenance
JS10/2 MAINTENANCE 1. Always allow the heater to cool down before cleaning it. 2. Wipe the exterior surface of the heater occasionally with a soft damp cloth (not dripping wet) and dry the exterior surface before operating the heater. WARNING: Do not immerse the heater in water. -
Page 21: Warranty And Returns
All warranties issues should be made in writing to the address below. They can also be made via email to the email address below. Warranties will only be adhered too upon receipt of the goods to the address below and the final decision is at the discretion of the Ecovolt Engineers Ecovolt Limited...
Need help?
Do you have a question about the Joule Therm JT6r and is the answer not in the manual?
Questions and answers