Do you have a question about the JTB Series and is the answer not in the manual?
Questions and answers
Tommy walsh
March 31, 2025
How to use ecovolt with push button
1 comments:
Mr. Anderson
March 31, 2025
To use the Ecovolt JTB Series heater with a push button:
1. Restore Factory Settings: - Make sure the heater is in power off mode. - Press and hold the button for 20 seconds. - Release the button when indicated on the display. - Press the button again to accept and restore factory settings.
JTB Electric Radiators Installation and Operational Manual Read the instruction manual carefully before commencing the installation Installation should be completed by a competent person All electrical work to be completed by a qualified electrician Please dispose the package properly. Towel Rail Installation Tools Required to complete the installation 1.
Page 3
Installing the female wall brackets Using a measuring tape, spirit level and pencil, mark the wall where the 4 female brackets are to be positioned. It is important to line the male spigot bracket attached to the heater to your markings. Using the drill, drill 4 holes in the wall and insert wall plugs.
Page 4
Fixing the heater to the female brackets Line up the male spigot brackets on the back of the heater and insert them into the female brackets. Using the screwdriver and the security bolts, secure the heater and ensure the bolt is tight. The heater is now secure to the wall.
Filling the heater with water - JT4B – Pour 330ml of water into the heater - JT6B – Pour 450ml of water into the heater Fit and tighten the 4 valve locks into the sides of the heater. Fill the heater with the correct amount of water and fit the 5th valve lock with bleed valve to the top of the heater as shown below Connecting the heater to the 230V electricity supply...
Page 6
LCD Digital Thermostat Manual The following information is intended only for the digital thermostat that can be fitted to the JTB heater as shown below. LCD Digital Thermostat Description 1. General information: a) Power specification: AC230V/50HZ b) Temperature range: 0~55 c) Setting temperature range: 7~30 d) Time mode: 24 hour e) Week mode: 1~7...
Page 7
3. Functions and heating modes: 3.1 Comfort mode: Setting the temperature in the daytime, Icon, available temperature range 7 C~30 3.2 Economy mode: Setting the temperature in the night, Icon , available temperature range 7 C~30 C. The Max temperature shall not exceed the comfort temperature 3.3 Defrost mode: Setting the temperature at 7 Icon,...
Page 8
4. Mode operation instructions: 4.1 Start up: Press to turn on the heater. All buttons are invalid the heater is on 4.2 Change heating modes: The factory default setting when the heater is turned on is comfort mode, press to switch the mode to the following, comfort mode →...
Page 9
4.2.4 Timing mode : Setting the timing mode for the heater. 4.2.4.1. Time setting: When enter the timing mode in the first time, the icon “00:00” is flashing, press for 3 seconds, the icon“00” is flashing. Press to adjust the time. Adjustment range is 0~23H, in hourly segments.
Page 10
4.2.4.3. Daily programming setting: After completing the week setting, press to enter the daily programming setting. Press to set the daily programming setting. (P1-P5), comfort mode is indicated by( )in the time axis. Economy mode is indicated by in the time axis. P1: Comfort mode: 06:00 - 22:00 (Economy mode all other times outside these times).
Page 11
4.2.4.4. Daily programming modification: Hold for 3s to enter the daily programming section, the are used to toggle between comfort and economy heating times. Pressing will select comfort heating for that hour of the day, pressing will select economy heating for that hour. The icon on the display indicates the amount of time the comfort heating is set for.
4.2.6 BOOST function: It is possible to boost the heating from 30mins to 2 hours. Press the for 3s in the BOOST function. The BOOST function will turn the heating mode to comfort for 30 minutes to 2 hours (the default time is 2 hours), press to adjust the duration of the BOOST function to 30 minute segments.
Ecovolt replacement with a functionally equivalent product. The Ecovolt guarantee is valid for 2 years from the date of purchase of your Ecovolt product or date of delivery. The Ecovolt guarantee is conditional upon you providing the original purchase receipt as proof of purchase.
Page 14
Terms and Conditions of the Ecovolt Guarantee • The Ecovolt guarantee is valid for 2 years from the date of purchase of your Ecovolt product from a recogised retailer or from the date of delivery. The original receipt is required as proof of purchase to validate the guarantee period.
Need help?
Do you have a question about the JTB Series and is the answer not in the manual?
Questions and answers
How to use ecovolt with push button
To use the Ecovolt JTB Series heater with a push button:
1. Restore Factory Settings:
- Make sure the heater is in power off mode.
- Press and hold the button for 20 seconds.
- Release the button when indicated on the display.
- Press the button again to accept and restore factory settings.
2. Factory Default Settings After Reset:
- Comfort mode temperature: 19°C
- Economy mode temperature: 15.5°C
- Time: “0000”
- Day: “1”
- BOOST function default time: 2 hours
- Temperature calibration: “0”
These functions are controlled using the push button as indicated.
This answer is automatically generated