1. Important Safety Information …………………1 2. Main Technical Parameters……………………1 User’s Manual 3. Main Features …………………………………2 4. Working Principle and Main Structure ………2 5. Installation and Adjustment ……………………2 Model:DKC400(U) & DKC400(U)Y ………………………10 6. Connecting - DKC400(U) ……………………11 7. Connecting - DKC400(U)Y 8.
Be careful when in close proximity to moving parts where hands or fingers could be gate. pinched. Control board not included in DKC400(U) main unit, it can be fitted with the XF24W(AC220V) Do not allow control devices to be placed so that a person can access them by reaching or XF24U(AC110V) control box according to your needs.
Page 3
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL Fig.4 DKC400(U) Gate operator with spring limit switch Fig.2 DKC400(U)Y Gate operator with spring limit switch Conduit In order to protect the wires, use PVC conduit for wires, conduit must be set into the concrete when it is poured.
Page 4
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL The space between rack and gear is about 1mm. Bring another rack element near to the previous one. Move the gate manually and weld the three pawls as the first rack, thus proceeding until the gate is fully covered.
Page 5
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL Spring limit switch upper and another is lower. The magnet position can be installed in the middle so it Install the block as shown in Fig.10 and Fig.11. Release the gear clutch with the key and push inducts both reed switches.
Page 6
Rack Magnet bracket Block The DKC400(U) has a terminal block, Fig.13 shows the wiring of motor and limit switch, the Style I (see Fig.9) Steel DKC400(U) is not equipped with control box, the control box (XF24W or XF24U) can be Magnetic limit switch Style II (see Fig.9)
Page 7
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL 7. Connecting ----DKC400(U)Y Wiring notes for control board (KZB01) Make sure that the power is OFF before making any electrical connections. Power switch: ON/OFF Fuse: DKC400Y/XF24W: 5A, Ø5x20;...
Page 8
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL 9. Limit switch: CL (Close limit), CO (Com), OP (Open limit),DC12V (Output power supply) N.O. (For N.O. limit switch) N.C. (For N.C. limit switch) Limit switch mode is adjustable by DIP-switch.
Page 9
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL Wiring notes for control board (KZB05) 9. Limit switch: CL (Close limit), CO (Com), OP (Open limit),DC12V (Output power supply) Power switch: ON/OFF Fuse: DKC400Y/XF24W: 5A, Ø5x20; DKC400UY/XF24U: 10A, Ø5x20...
Page 10
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL Wiring notes for control board (KZB13) 1. Fuse: DKC400Y/XF24W: 5A, Ø5x20; DKC400UY/XF24U: 10A, Ø5x20 2. Power Input: E (Earth), L (Live), N (Neutral) DKC400Y/XF24W: AC220V; DKC400UY/XF24U: AC110V 3.
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL 8. Control Not used Open Below are all of the available remote controls for DKC400 series gate operators, the remote control came with your operator depends on your order. Signal Additional remote controls can be purchased through your dealer.
Page 12
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL Set auto-close function (This feature can be selected to make the gate stay open for some stop cycle. seconds before it automatically closes. The auto-close time can be adjusted to between 0 and Button 1, button 2 and button 3 are used to open or close the gate.
Page 13
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL ﹡Set auto-close function of pedestrian mode: for control board KZB01 or KZB05, please turn ﹡Keep width of pedestrian mode, cancel auto-close function of pedestrian mode: for control...
DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL DKC400(U) & DKC400(U)Y SLIDING GATE OPERATOR USER’S MANUAL Activities Covered in this section less than 5 minutes. If is runs continually for an extended period of time, the thermal protector Remote control: With each press of the button, the gate will close, stop, open or stop cycle.