Advertisement
Quick Links
Advertisement
Related Manuals for ZHEJIANG XIANFENG MACHINERY K207A
Summary of Contents for ZHEJIANG XIANFENG MACHINERY K207A
- Page 1 K207A SWING GATE OPENER USER’S MANUAL ZHEJIANG XIANFENG MACHINERY CO., LTD.
- Page 2 Read the entire user’s manual before beginning installation, and carefully obey the following instructions: To prevent the risk of electrocution, be sure to turn off all power to the K207A until installation is complete. The Gate Opener should be installed by a qualified technician. Otherwise, serious personal injury or property damage may occur.
- Page 3 Opening and closing time have been preset in 24 sec. Aluminum and cast metal housing. For your safety, the K207A will stop and reverse if it encounters an obstruction during closing and stop when it encounters an obstruction during opening.
- Page 4 K207A Swing Gate Opener User’s Manual Exploded View and Parts List 1.Hood pipe 29.24T planet carrier 2.End joint 30.Bearing 61800 3.Pin 10x40 31.Elastic circlip 19 4.Steel tube 32.24T ring gear 5.Small support ring 33.Bearing 61800 6.Right housing 34.Locating shield 7.Screw M5x20 35.Pin 4x20...
- Page 5 K207A Swing Gate Opener User’s Manual Mechanical Installation Begin with both openers unlocked. Next identify if this will be a “push to open” or a “pull to open” installation. In either configuration, the gate is mounted on one face of the mounting post, and the opener is mounted on the face 90 degrees from it.
- Page 6 K207A Swing Gate Opener User’s Manual The installation should meet the specifications shown in figure 3. See Fig. 3. Fig. 3 Retainer (close position) Cmax α 90° 105° Gate opener Cmax Enlarge Retainer (open position) Main Structure Fig. 4 Special motor...
- Page 7 K207A Swing Gate Opener User’s Manual The installation height range is 1.18 – 3.15 inches (300 – 800mm). See Fig. 5. Fig. 5 Gate post Gate opener Gate Electric lock Front and Rear Parts of Gate Opener To install the rear part of the gate opener, insert shoulder screw and spacer, then tighten with the nut.
- Page 8 K207A Swing Gate Opener User’s Manual To install the front part, fit the hole in the front part with the hole in the supporting plate, and push the axle pin into the holes (using hands or a hammer), and finally fit the retainer clip. See Fig. 7.
- Page 9 K207A Swing Gate Opener User’s Manual Hood Shield Install the hood pipe, tighten the screws into the opener and cover the plastic split ring over the joint. See Fig. 9. Fig. 9 Hood pipe Main unit Hood pipe Screw Plastic split ring Waterproof caps There are 8 caps in total 4 to be used and 4 spares.
- Page 10 K207A Swing Gate Opener User’s Manual If the maximum angle for installing is 105°, the retainer should be installed on the ground at approx. 100°. If the installing angle is 90°, the retainer should be installed at 90°. See Fig. 3.
- Page 11 K207A Swing Gate Opener User’s Manual can be welded on the gate section with the lock so that when it closes, it will trap the gate section without the lock between itself and the center stop block, thus locking both gate sections.
- Page 12 Connect electronic lock (3)Install the External Keypad/Button Switch The K207A is equipped with an interface for an external button switch or keypad. To install the keypad attach two wires of your keypad to the O/S/C terminal. The keypad will function in single channel mode.
- Page 13 K207A Swing Gate Opener User’s Manual (1) Learn / erase remote controls Adding extra remote controls (Learn): Press red button on the control board (see Fig.14 No.12), then the ‘LED’ (see Fig. 14 No.11) will be on, it will turn off when you press any remote control button.
- Page 14 K207A Swing Gate Opener User’s Manual (4) Auto-reverse function Turning the auto-reverse safety function: Rotating the ‘FORCE ADJ’ (see Fig.14 No.4 and No.5) with a screwdriver, No.4 force adjustor can be used to adjust No.1 gate-leaf which has lock, No.5 force adjustor can be used to adjust No.2 gate-leaf.
- Page 15 K207A Swing Gate Opener User’s Manual Fig.14 control board diagram...
- Page 16 K207A Swing Gate Opener User’s Manual Table 2 wiring notes of control board Position Function Remark Transformer input AC220V Transformer output AC12V Fuse 5 20 2A The resistance may be increased or Force adjustor (for No.1 gate-leaf with decreased by rotating clockwise or electrical lock) anticlockwise.
- Page 17 K207A Swing Gate Opener User’s Manual 3. Troubleshooting (see Table 3) Table 3 Troubleshooting Symptoms Possible cause Remedy (1) Make sure that power is ON. (1) Power is OFF. (2) Remove obstructions. Gate will not open or close (2) The gate is obstructed.