Advertisement
Quick Links
1000 mm - 39
914 mm
36''
Fig. 1
958 mm-37
13
20 mm-
/
''
16
Electrical Connection:
120/240 VAC, 3 Pole, 4 Wire
(See Table 2 for amperage)
Fig. 3
CLUNY
3
/
''
8
768 mm
30
399 mm
11
15
/
''
16
11
/
''
16
225 mm
7
8
/
''
8
60 mm
3
2
Gas Connection :
Male coupling, 1/2" ID NPT
73,500 BTU
(5 Burners => 60,000 BTU)
(Oven => 13,500 BTU)
ATTENTION!!
USING HANDLES/BARS TO LIFT
WILL DAMAGE THE RANGE AND
VOID THE WARRANTY!
Page 1 of 8
INFORMATION
Back space vent
(A)
1
/
4
1065 mm
15
41
/
''
16
940 mm
37''
147 mm
25
5
/
''
32
Gas Connection
Electrical
Connection
/
''
8
1
800 mm-31
/
''
2
5
727.5 mm-28
/
''
8
9
650 mm-25
/
''
16
7
671 mm-26
/
''
16
7
708 mm-27
/
''
8
Fig. 2
7
47 mm-1
/
''
8
15
430 mm-16
/
''
16
40 mm
9
1
1
510 mm-20
/
''
16
Fig. 4
34 mm
5
1
/
''
16
/
''
16
Advertisement
Related Manuals for Lacanche CLUNY LG1052G
Summary of Contents for Lacanche CLUNY LG1052G
- Page 1 CLUNY INFORMATION Back space vent 800 mm-31 ’’ 34 mm 727.5 mm-28 ’’ ’’ 650 mm-25 ’’ 1000 mm - 39 ’’ 914 mm 671 mm-26 ’’ 768 mm 36’’ 708 mm-27 ’’ Fig. 1 1065 mm Fig. 2 ’’ 399 mm 940 mm ’’...
- Page 2 CLUNY INFORMATION Cooking surface description : The range top has 5 burners of different size and power individually controlled by a safety valve and ignited by an electric ignition. The “TRADITIONAL” model is equipped with a 385 x 510 mm (15 ’’...
-
Page 3: Cabinet Preparation
CLUNY INFORMATION Cabinet Preparation Gas pipe from Electrical connection access Fig. 6 range in this area panel of range in this area NOTE: The above diagram depicts the actual location of gas and electrical connections on the range. DO NOT place gas stub-out or electrical receptacle in these areas. Place them nearby in accordance with local regulations. -
Page 4: Electrical Connection
CLUNY INFORMATION Electrical Connection Note: • ALL WORK ON OR REPAIR OF AN APPLIANCE MUST BE CARRIED OUT BY A QUALIFIED INSTALLER. • WHEN INSTALLED, THE APPLIANCE MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH THE LOCAL CODES OR The National Electrical Code, ANSI/NFPA 70-1996 or latest edition. - Page 5 CLUNY INFORMATION Connecting Electrical Power : On terminal block at the rear of the appliance. Use flexible cord in accordance with standard N.E.C., AINSI/NEMA 70-1996 or latest edition (no cord provided). Use a 4-wire rated for 15-30 A 125/250 VAC, type SRD, SRDT, S, SO or ST. See power specification chart for your model (Table 2).
-
Page 6: Gas Connection
CLUNY INFORMATION Gas Connection Note: • The range must be installed under an exhaust hood. In the Commonwealth of Massachusetts, the exhaust hood must be equipped with an "interlock" system. Check local codes. • Do not install this unit near combustible walls, partitions, pieces of furniture, or decorative material unless these are covered with adequate thermal insulation of the noncombustible type. - Page 7 CLUNY INFORMATION Back Spacer Vent Fitting In order to meet UL requirements, it is MANDATORY to mount the back spacer vent A supplied with the appliance (or equivalent) to the wall, this allows for ventilation and provides safety clearances to prevent heat damage. Screw the 2 brackets G to the wall according to figures 14, 15 and 16 (screws not supplied), then fit the back spacer vent onto these brackets by using the washers and nuts supplied with the range.
- Page 8 CLUNY INFORMATION Stability Device Installation Screw the anti-tip bracket H to the wall according to figures 15, 16 and 17 (screws not supplied). Remove the left-hand drawer; push the range against the wall until the anti-tip bracket screw goes through the back of the range.