Summary of Contents for Nailor MAC-700
- Page 1 NstALLAtION perAtION & AINteNANce Mobile Air Cleaner Unit w / HEPA Filter Model MAC-700 Read completely and save these instructions for future reference.
- Page 2 Nailor Industries of Texas, Inc. 4714 Winfield Road, Houston, TX 77039 Tel.: 281-590-1172 nailor.com Page 2 of 14 4/21 IOM-MAC-700-INST Nailor Industries Inc. reserves the right to change any information concerning product or specification without notice or obligation.
-
Page 3: Table Of Contents
Inspect all cartons and boxes for flaws and shipping damages. If anything is discovered to be damaged, contact the shipping company and file a freight claim. 4/21 IOM-MAC-700-INST Page 3 of 14 Nailor Industries Inc. reserves the right to change any information concerning product or specification without notice or obligation. -
Page 4: Product Overview
Step 2 Wipe down the unit to remove shipping dust and debris. Step 3 Plug into the wall outlet. The MAC-700 unit is furnished with a 120 V plug for utilizing in a standard wall outlet. A qualified person should wire the unit to the appropriate power supply and install the UV lights. Refer to the wiring diagram on page 9 or 10. -
Page 5: Uv Lights Installation
LAMP LIFE: MAC-700 UV-C lamps are rated at 9,000 hours with no more than a 20% output loss at the end of the lamps life (12 months of continuous use). Lamps are constructed with UV-C resistant bases and will not produce ozone. - Page 6 HOUR METER AND RESET BUTTON: MAC-700 is equipped with an hour meter that counts the number of hours that unit has been On. The UV-C lamps should be replaced when the hour meter number reaches to 9,000. After removing the old lamps, while pressing the safety switch, hold the rest button for 3 - 4 seconds to rest the hour meter and then install the new lamp.
-
Page 7: Hepa Filter And Pre-Filter Removal And Replacement
HEPA FILTER AND PRE-FILTER REMOVAL AND REPLACEMENT The MAC-700 contains a MERV 10 pre-filter and a 6" HEPA filter. Both filters can be replaced without any special tools. It is recommended to change the pre-filter every 3 months and HEPA filter every 12 months. However, filter life is variable based on air quality and the speed of blower. -
Page 8: Control Box
CONTROL BOX The MAC-700 contains a 11" x 8" (279 x 203) control box that includes terminal blocks and transformer, reset button and UV lights ballast. Figure 6. Control Box Layout Page 8 of 14 4/21 IOM-MAC-700-INST Nailor Industries Inc. reserves the right to change any information concerning product or specification without notice or obligation. -
Page 9: Wiring Diagram - 3 Color Wire - Uv Light Cable - Bipolar Ionization
3-Color Wire UV Light Cable - Bipolar Ionization PRESSURE SWITCH SWITCH BK-WH BK-RD LIGHT ON/OFF SWITCH 4/21 IOM-MAC-700-INST Page 9 of 14 Nailor Industries Inc. reserves the right to change any information concerning product or specification without notice or obligation. -
Page 10: Wiring Diagram 2-Color Wire Uv Light Cable
2-Color Wire UV Light Cable RD-YE PRESSURE SWITCH BL-WH SWITCH BK-WH BK-WH BL-RD LIGHT ON/OFF SWITCH Page 10 of 14 4/21 IOM-MAC-700-INST Nailor Industries Inc. reserves the right to change any information concerning product or specification without notice or obligation. -
Page 11: Bipolar Ionization - Gps-Fc24-Ac
Needlepoint Bipolar Ionization (NPBI) technology cleans indoor air. This technology produces a high concentration of positive and negative ions, delivering them to the space via the MAC-700. Within the air stream, ions attach to particles, where they combine, become larger and are more easily filtered from the air. When ions come in contact with pathogens, they disrupt the pathogens’... - Page 12 Adjust height of emitters: Loosen screw at base of emitter, gently push or pull emitter to a height where wiper just contacts emitter. Hold the emitter in place and tighten screw. Verify correct height after tightening screw. • If unit does not operate properly after verifying the above instructions, please contact Nailor for additional assistance. Electrical listings: UL, cUL...
-
Page 13: Motor/Blower Removal And Replacement
Adjust the motor speed by rotating speed controller knob counterclockwise. Verify all filters are properly in place. 4/21 IOM-MAC-700-INST Page 13 of 14 Nailor Industries Inc. reserves the right to change any information concerning product or specification without notice or obligation. - Page 14 Page 14 of 14 4/21 IOM-MAC-700-INST " C o m p l e t e A i r C o n t r o l a n d D i s t r i b u t i o n S o l u t i o n s . "...