Advertisement
Quick Links
Advertisement
Related Manuals for Jenoptik JenLas D2 Series
Summary of Contents for Jenoptik JenLas D2 Series
- Page 1 Disk Laser JenLas D2.x ® Installation Instructions...
- Page 2 JENOPTIK l Healthcare & Industry JENOPTIK Laser GmbH Goeschwitzer Str. 29 D-07745 Jena (Germany) Service Department: Phone: + 49 3641 65-2102 Fax: + 49 3641 65-2109 Email: laser.service@jenoptik.com Internet: http://www.jenoptik-los.com You can use the --> 5 Fax Form p. 16, for your requests.
- Page 3 The equipment is subject to changes due to ongoing product development. This documentation is not included in any update service. © Unless expressly authorized in writing by JENOPTIK Laser GmbH, forwarding and duplication of this document, and the utilization and communication of its contents are not permitted.
- Page 4 Dear user In this documentation, the following characters, symbols and pictograms are be- ing used: Note --> Cross-reference to sections or illustrations of this manual • Operations to be performed Enumeration Danger: Warning Warning symbols Warning: Risk to human health in the case of non-observance. Caution: Possible damage to the device.
-
Page 5: Table Of Contents
Contents Contents Safety Notes ..................6 Warning labels and type label ..............7 General ....................7 RoHS Directive ..................8 Installation ..................9 Technical Data ..................14 Appendix ..................15 Fax Form ...................16... -
Page 6: Safety Notes
Safety Notes Safety Notes Warning: Laser radiation! The Disk Laser may be installed and put into operation only by appropriately qualified and instructed personnel. Make sure the device is not used improperly. The device does not contain any safety devices such as shutters, emission warning lamps, emergency stop button, power switch, etc. -
Page 7: Warning Labels And Type Label
Prior to start-up of the device, make sure it is in perfect condition. Modifications and repairs of the device are subject to safety regulations and may only be performed by JENOPTIK Laser GmbH. Strictly observe all warning labels. -
Page 8: Rohs Directive
Safety Notes In inactive mode, absolutely make sure to provide ESD protection (ESD = electrostatic discharge) by shorting the connection terminals (if built in, by relay contact, otherwise by a short-circuit bridge). Prior to opening the packing, make sure the device has normalized to ambient temperature to avoid condensation. -
Page 9: Installation
Installation Installation The mounting holes (6 to 9 or 12, Fig. 2), the sub-D connector (5), the electric terminals (2, 4) and the optical beam exit aperture represent the interface to the user-specific use of the device. Make sure to observe the --> Safety Notes, p. 6, to avoid any risk. Caution: ESD protection! Avoid any electrostatic discharge and observe the rules for ESD protection. - Page 10 Installation 92.5 M4 6 mm tief ∅ 5.6 ∅ 3.9 19.7 ∅ 4D10 ∅ 5.6 Fig. 3 Geometrical mounting dimensions...
- Page 11 Installation Caution: ESD protection! Avoid any electrostatic discharge and observe the rules for ESD protection. The fitter, the workbench and the used tools must be grounded. • Mount the subassembly to an appropriate cooling unit with Peltier cooling element by means of the screws (6, 7, 9 or 12, Fig. 2, p. 9). The contact surface of the cooling unit must be sufficiently flat and clean.
- Page 12 Installation • Connect the connection cable to the 9-pin Sub-D connector (4). Secure the cable by fastening the slotted screws of the connector by means of a torque-controlled screwdriver adjusted to 0.6 Nm (60 Ncm). Important: The use of normal screwdrivers or other tools is not permissible. Make sure to prevent any impact and tensile load to this connector indepen- dent of the direction of action.
- Page 13 Installation The temperature regulation should not be faster than 15 K/min. Caution: Temperature adjustment! Before applying the diode current, the LBO temperature and the diode tempera- ture must be adjusted according to the specifications of the --> Device Card. Make sure that the constancy of LBO temperature and diode temperature com- plies with your -->...
-
Page 14: Technical Data
Technical Data Technical Data Feature Operating data Limit values as per EN 60825-1 Laser Disk laser Laser Class 4 as per EN 60825-1:2007 Wavelength 532 nm ± 1 nm Output power 3/5 W (cw) 10 W (cw) Power stability (rms) <... -
Page 15: Appendix
Appendix Appendix NTC resistance temperature values B T + 273,15 K T + 273,15 K Type EPCOS G560, 10kΩ @ 25°C / 77 F, Toleranz ∆T ≤ ±1.0°C / 34 F (range 0°C / 33 F to 40°C / 104 F) Approximation formula: B T + 273.15 K T + 273.15 K... -
Page 16: Fax Form
Fax Form Fax Form JENOPTIK Laser GmbH Goeschwitzer Str. 29 Service Department: Fax: + 49-3641-65 4011 Our Ref.: .......... Your Ref.: ..........Pages (incl. cover page): ....Date: ............. Message (with brief description of faults JenLas D2.x): ® Sender: ......................