Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PSIS 10-230V
Summary of Contents for Trotec PSIS 10-230V
- Page 1 PSIS 10-230V ORIGINAL INSTRUCTIONS DIGITAL SOLDERING STATION...
-
Page 2: Table Of Contents
Info Information marked with this symbol helps you to carry out your tasks quickly and safely. Follow the manual Information marked with this symbol indicates that the operating manual must be observed. digital soldering station PSIS 10-230V... -
Page 3: Safety
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries. digital soldering station PSIS 10-230V... - Page 4 DIY sectors. It can be used for soldering works, glue welding plastics or for applying embellishments. We recommend using the power tool with original Trotec accessories. digital soldering station PSIS 10-230V...
- Page 5 Risk of fire! Only use the holder included in the scope of delivery or another fireproof base or mat for setting down the hot soldering iron. Warning Risk of fire! Never leave the activated device unattended. digital soldering station PSIS 10-230V...
-
Page 6: Information About The Device
2. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket. 3. Do not reconnect a defective device to the mains. digital soldering station PSIS 10-230V... - Page 7 Indicates current and target Soldering iron holder desired temperature temperature (while settings are Storage compartment for soldering sponge being made) Soldering sponge Solder Soldering tips Soldering iron Storage compartment for soldering tips Storage compartment for solder digital soldering station PSIS 10-230V...
-
Page 8: Transport And Storage
• Clean the device as described in the Maintenance chapter. Weight 1.0 kg When the device is not being used, observe the following storage conditions: • Dry and protected from frost and heat • Ambient temperature below 45 °C • protected from dust and direct sunlight digital soldering station PSIS 10-230V... -
Page 9: Start-Up
Afterwards, tin-coat the soldering tip again by applying some solder and soldering flux around the tip, then heat the tip. 4. Turn the new soldering tip (8) clockwise into the soldering iron (9). digital soldering station PSIS 10-230V... - Page 10 • Make sure that the molten solder entirely covers the solder pad and surrounds the connection wire completely. 2. Set the on/off switch (1) to position "I". ð The last preset temperature (default setting 300 °C) is indicated on the display (16) for 3 seconds. Afterwards, the display indicates the current temperature. digital soldering station PSIS 10-230V...
- Page 11 Soldering flux is required to perform soldering work. The soldering flux is either part of the soldering agent or must be applied separately. Find out more about a suitable soldering agent for your intended application. digital soldering station PSIS 10-230V...
-
Page 12: Available Accessories
Using insertion tools or accessories other than those specified in the operating manual may cause a risk of injury. Accessories Article number Set of soldering tips 6.236.001.001 digital soldering station PSIS 10-230V... -
Page 13: Maintenance
• Dry the device with a soft, lint-free cloth. • Regularly clean the soldering tips by wiping them on the moistened soldering sponge and by tin-coating them afterwards. • Do not use any chemicals for cleaning the soldering tips. digital soldering station PSIS 10-230V... -
Page 14: Disposal
PSIS 10-230V... - Page 15 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...