Table of Contents
Advertisement
Quick Links
HUMIDITY/TEMPERATURE/DOOR AND
WINDOW/ACCELERATION SENSOR
SMART-HS0101
User Manual
Vega Smart-HS0101 sensor combines a several
functions, namely: door and window sensor,
accelerometer, which determines the presence of
vibration and the angle of deviation from the vertical,
control of temperature and humidity parameters of the
environment with the ability to set the ranges of these
parameters. When any of the alarm events occur the
message with corresponding information sent to
LoRaWAN™ network.
www.vega-absolute.ru
Advertisement
Table of Contents
Related Manuals for Vega Absolute SMART-HS0101
Summary of Contents for Vega Absolute SMART-HS0101
- Page 1 HUMIDITY/TEMPERATURE/DOOR AND WINDOW/ACCELERATION SENSOR SMART-HS0101 User Manual Vega Smart-HS0101 sensor combines a several functions, namely: door and window sensor, accelerometer, which determines the presence of vibration and the angle of deviation from the vertical, control of temperature and humidity parameters of the environment with the ability to set the ranges of these parameters.
- Page 2 Smart-HS0101 / User Manual Document Information Humidity/temperature/door and Title window/acceleration sensor Smart-HS0101 Document type Manual – Translation from Russian Document number V05-HS0101-01 Revision and date 01 – 01 February 2019 This document applies to the following products: Product name Type number...
-
Page 3: Table Of Contents
“LoRaWAN settings” tab ................................. 19 “Smart-HS0101” tab ................................24 5 COMMUNICATION PROTOCOL ............................26 SMART-HS0101 transmits the following types of packets ....................26 SMART-HS0101 receives the following types of packets ....................28 6 STORAGE AND TRANSPORTATION REQUIREMENTS ...................... 30 7 CONTENT OF THE PACKAGE ..............................31 8 WARRANTY .................................... -
Page 4: Introduction
Smart-HS0101 / User Manual INTRODUCTION This manual is designated for Vega Smart-HS0101 humidity/temperature/door and window/acceleration sensor (hereinafter – device, sensor) manufactured by Vega-Absolute LLC and provides information on powering and activation procedure, control commands and functions of the device. This manual is targeted at specialists familiar with installation work fundamentals for electronic and electrical equipment. -
Page 5: Description And Operation
1 DESCRIPTION AND OPERATION DEVICE DESCRIPTION Vega Smart-HS0101 sensor designed for distance control both opening and closing different doors and windows, for determine an angle of deviation from the vertical of some objects or for fix an move starting and also for measurement of humidity and temperature parameters including control of coming out the specified range of these parameters. -
Page 6: Functional
The internal clock is set automatically when device connected to the "Vega LoRaWAN Configurator" via USB, also adjustable via LoRaWAN. FUNCTIONAL Vega Smart-HS0101 sensor is class A device (LoRaWAN classification) and has the following features: o Frequency plans RU868, EU868, IN865, AS923, AU915, KR920, US915, KZ865... -
Page 7: Marking
Smart-HS0101 / User Manual MARKING Device marked with sticker that contain the next information: o Device model; o DevEUI; o Month and year of manufacture; o QR-code containing DevEUI for automatized count. Sticker located in three places – on device case, in factory certificate and on the packing box. -
Page 8: Specification
Smart-HS0101 / User Manual 2 SPECIFICATION Main USB-port micro-USB, type B Operating temperatures -40…+85 °С Built-in temperature sensor Built-in humidity sensor LoRaWAN AppEui by default 736D687330313031 LoRaWAN class Quantity of LoRa channels Frequency plan RU868, EU868, IN865, AS923, AU915, KR920, US915, KZ865, custom (EU868... -
Page 9: Operation
Smart-HS0101 / User Manual 3 OPERATION INDICATION A triple color indicator is located on the front of the sensor case and it informs a user about the device state. Indicator on the front of the device case Indicator signal Meaning... -
Page 10: Mounting Options
Smart-HS0101 / User Manual MOUNTING OPTIONS Door and window sensor considers interdependent placement of two components: - main part including all of electronics, - magnet. Device contain two Hall sensors located in two different places on a board. That allows mounting device in two ways. -
Page 11: Initial Startup
2 responds to the movement of the magnet. Magnet to the left, Hall sensor 1 works INITIAL STARTUP Vega Smart-HS0101 sensor powered by the CR123A 3V 1400 mAh replaceable battery. You need to insert the battery observing the polarity before start. Insert the battery CR123А into the... - Page 12 Smart-HS0101 / User Manual Press the start button located on the board 2. OTAA. After pressing the start button, the device makes three attempts to connect to the network within the set frequency plan. After the activation request confirmed by LoRaWAN network, the device sends a signal and switches to the "Active"...
-
Page 13: Connecting Via Usb
Smart-HS0101 / User Manual CONNECTING VIA USB The device Smart-HS0101 can be configured with the "Vega LoRaWAN Configurator" application (See part 4). micro-USB Before connecting the device to the computer for the first time, you must install the driver for the COM port stsw-stm32102, which can be downloaded from iotvega.com. After running the executable file VCP_V1.4.0_Setup.exe, the installer window will appear:... - Page 14 Smart-HS0101 / User Manual After pressing Finish the driver is ready for operation, - it is possible to connect the device via USB. Revision № 01 - 01 February 2019...
-
Page 15: Vega Lorawan Configurator
Smart-HS0101 / User Manual 4 VEGA LORAWAN CONFIGURATOR The "Vega LoRaWAN Configurator" application (hereinafter referred to as the configurator) is intended for setting up the device via USB. The configurator has two modes of operation - "Simple" and "Expert". In the "Simple"... -
Page 16: Connection To The Device
Smart-HS0101 / User Manual CONNECTION TO THE DEVICE For the connection to the device, perform the following steps: 1. Connect the USB cable to the device. 2. Start the "Vega LoRaWAN Configurator" application. 3. Click the "Connect" button in the menu on the left. -
Page 17: Device Info" Tab
Smart-HS0101 / User Manual “DEVICE INFO” TAB The "Device info" tab displays information about the device, its status, and the data needed to register the device in the LoRaWAN network. ABP info - displays the data necessary to register the device in the LoRaWAN network with ABP method (Activation By Personalization). - Page 18 Smart-HS0101 / User Manual Join network button - launch the LoRaWAN network connection procedure with the previously selected ABP or OTAA method. If the device is already connected to the network, reconnection procedure will occurs. Link check (not displayed in the "Simple" mode) - when pressed, the device sends a special signal to the LoRaWAN network, in response to which the network informs it of the number of gateways that received this signal and the signal quality.
-
Page 19: Lorawan Settings" Tab
Smart-HS0101 / User Manual “LORAWAN SETTINGS” TAB The "LoRaWAN Settings" tab allows you to configure various parameters of the LoRa network. Region - allows you to select one of installed frequency plans or specify a custom frequency plan. Custom frequency plan is EU-868 based. - Page 20 Smart-HS0101 / User Manual This frequency plan allows you to set up to 16 channels, as well as the frequency and speed of the second receiving window. The first three channels and the second receiving window parameters are mandatory. Without these parameters the custom frequency plan will be considered empty.
- Page 21 Smart-HS0101 / User Manual signal received by the network, the higher the speed will be installed on the device. This option is recommended only on permanently installed devices. RX1 offset (not displayed in the "Simple" mode) – specifies the time between end of packet transmission and first receiving window opening.
- Page 22 Smart-HS0101 / User Manual Uplink number of transmission (not displayed in the "Simple" mode) – if the "Confirmed uplinks" function is disabled, the device will simply send each packet as many times as specified in this option. If "Confirmed uplinks" is enabled, the device will send packets until it receives a confirmation or until it sends as many packets as specified in this option.
- Page 23 Smart-HS0101 / User Manual TX datarate (not displayed in the "Simple" mode) – the device transmission datarate at which it will transfer packets to the LoRaWAN network. This speed can be change by the network server if the ADR algorithm enabled.
-
Page 24: Smart-Hs0101" Tab
Smart-HS0101 / User Manual “SMART-HS0101” TAB The “Smart-HS0101” tab contains the settings of the connected device. Current state – displays the current parameters measurement by the device - the temperature, humidity, vertical tint angle, the battery level and two Hall sensors state. - Page 25 Smart-HS0101 / User Manual come. The data transfer period adjustable from 5 minutes to 24 hours. Data transferring in random point in time during set period. At the next communication session, the device starts sending accumulated packets with readings, from the earliest to the latest.
-
Page 26: Communication Protocol
Smart-HS0101 / User Manual 5 COMMUNICATION PROTOCOL This part describes the Smart-HS0101 communication protocol with LoRaWAN network. In fields consisting of several bytes, the little endian byte order is used SMART-HS0101 TRANSMITS THE FOLLOWING TYPES OF PACKETS 1. Packet with current readings and alarm events... - Page 27 Smart-HS0101 / User Manual 3. Settings packet – transmitting on LoRaWAN port 3 when settings request command received or device connected to the network Size in bytes Field description Data type данных 1 byte Packet type, this packet == 0...
-
Page 28: Smart-Hs0101 Receives The Following Types Of Packets
Smart-HS0101 / User Manual SMART-HS0101 RECEIVES THE FOLLOWING TYPES OF PACKETS 1. Real-time clock adjustment – sent by application on LoRaWAN port 4 Size in bytes Field description 1 byte Packet type, this packet == 255 8 bytes The value in seconds for which you need to adjust the time. - Page 29 Smart-HS0101 / User Manual Table of ID of Smart-HS0101 parameters and these possible values ID of Description Data Possible values parameter length Confirmed uplinks 1 byte 1 – confirmed 2 – unconfirmed Communication period 1 byte 1 – 1 hour 2 –...
-
Page 30: Storage And Transportation Requirements
Smart-HS0101 / User Manual 6 STORAGE AND TRANSPORTATION REQUIREMENTS The Smart-HS0101 sensor shall be stored in the original packaging in heated room at temperatures +5°С to +40°С and relative humidity less than 85%. The sensor shall be transported in covered freight compartments of all types at any distance at temperatures -40°C to +85°C. -
Page 31: Content Of The Package
Smart-HS0101 / User Manual 7 CONTENT OF THE PACKAGE The sensor is delivered complete with: Sensor Vega Smart-HS0101 – 1 pc. CR123A battery – 1 pc. Factory certificate – 1 pc. Revision № 01 01 February 2019... -
Page 32: Warranty
Smart-HS0101 / User Manual 8 WARRANTY The warranty period for the device is 5 years from the date of sale. The manufacturer is obligated to provide repair services or replace the failed device during the entire warranty period. The consumer undertakes to comply with the terms and conditions of transportation, storage and operation specified in this user manual. - Page 33 Smart-HS0101 / User Manual vega-absolute.ru Operation Manual © Vega-Absolute LLC 2019 Revision № 01 01 February 2019...