Advertisement
Quick Links
Installation instructions
for your new
CAUTION:
• Before you begin—Read these instructions, Owner's Manual and Important Safety Instructions
completely and carefully.
• This Kit is for use on models: JEM21K/L, JEM23K/L, JEM25L/GN/GV/GY/WN/WV/WY/BF/WF, JES833WY,
JEM825K, JEM27KWH/LWH, JEM31L/M/GN/GV/GY/WV/WY/GA/WA/CA/BF/CF/WF/SF, JEM33L/M, JEM34M
and ZEM200WN/WV/WY/GV/GY/SY/GW/WA/SA/GA/SF/BF/WF.
• This kit can be installed alone or over any General Electric/Hotpoint/RCA single electric wall oven.
• Do not alter or modify any part of this kit or the oven.
• Observe all governing codes and ordinances.
• Oven must be plugged into a properly grounded 3-hole, 120 volt receptacle as required by the
National Electrical Code.
• Unplug the microwave oven before attempting installation of this kit.
• Save these instructions (for Local Inspectors and Future Reference).
Parts List
1. Base Pan
2. Rear Duct
3. Side Covers (2)
4. Top Trim
5. Bottom Trim
6. Side Trims
7. Rear Holddown Brackets
Screws A (9 required 1 extra)
B (4 required 1 extra)
C (10 required 2 extra)
D (4 required 1 extra)
E (4 required 1 extra)
Note: This kit has extra screws to prevent technician from spending extra time locating a replacement in case
they lose one during installation.
Cabinet Cutout Dimensions and Specifications
Allow 1-1⁄4" for overlap of the Microwave Oven Kit
Trim over all the edges of the cutout for the
Microwave Oven Kit.
WIDTH
HEIGHT
24-7⁄8" 1⁄16"
15" 1⁄16"
DEPTH
16" Min. receptacle outside cutout
18" Min. receptacle inside cutout
120 volt—60 Hertz grounded power receptacle.
For Installation Above a Built-In Oven
Microwave oven should be installed on a
3⁄8" plywood base and supported by 2x4 or
1x2 equivalent runners on all sides. Base
must be capable of supporting a minimum
of 100 lbs.
4
5
6
1
Parts Inventory
16- 1/4"
26- 1/8"
Microwave Oven
Built-In Trim Kit
JX827BN, JX827WN,
JX827SS, JX827CD
7
D
A
B
E
C
Screw A
Screw B
Screw C
Screw D
Screw E
24-7 8" 1 16"
15" 1 16"
18" Min.
receptacle
in cabinet
16" Min.
receptacle
outside
cabinet
Advertisement
Related Manuals for GE JX827SS
Summary of Contents for GE JX827SS
-
Page 1: Microwave Oven
• Oven must be plugged into a properly grounded 3-hole, 120 volt receptacle as required by the National Electrical Code. • Unplug the microwave oven before attempting installation of this kit. • Save these instructions (for Local Inspectors and Future Reference). -
Page 2: Installation Procedure
Locating and Installing Rear Holddown Supports Set Base Pan (1) into the front cabinet microwave oven cutout and center it right and left. Push back until front flange is against cabinet front wall. Use the V-notch in the Base Pan front flange to center the Base Pan. - Page 3 Replace the screw removed from the top left to complete the rear duct installation. The Base Pan should be completely sealed to the microwave oven in the back and all screws installed in Steps 3 & 4 tightened. Step 5...
- Page 4 Step 7 Installing the Trim Kit Frame 1. Using the assembled Trim Kit Frame as a template (and with the microwave oven in position and secured), insert the Trim Kit Frame into the cutout and locate the attaching holes. Temporarily hold the...