GE JX9152 Installation Instructions Manual
GE JX9152 Installation Instructions Manual

GE JX9152 Installation Instructions Manual

Built-in trim kits
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Installation
Instructions
Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at: GEAppliances.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT
Save these instructions
for local inspector's use.
IMPORTANT
Observe all governing codes and
ordinances.
• Note to Installer – Be sure to leave these instructions with
the Consumer.
• Note to Consumer – Keep these instructions for future
reference.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time – 1 to 3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered
under the Warranty.
• This kit is for use on models:PEB9159DJ, PEB9159SJ,
PEB9159EJ and CEB1599SJ.
• This kit and microwave are approved for installation alone
or above any single electric wall oven. Do not mount
adjacent (within 2 feet) to any range, cooktop, gas oven, or
other microwave.
• This product is to be installed 3 feet above floor level.
• Do not alter or modify any part of this kit or the oven.
• For easier installation and personal safety, we
recommend that two people install this microwave oven.
• Unplug the microwave oven before attempting installation
of this kit.
WARNING
This oven must be plugged into a
properly grounded 3-hole, 120 volt receptacle as required by
the National Electrical Code.
WARNING
Before beginning the installation,
switch power off at service panel and lock the service
disconnecting means to prevent power from being switched
on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.

Microwave Oven

Built-In Trim Kits
JX9152 and JX9153

PARTS INCLUDED

PART
NOTE: This kit has extra screws to prevent the technician
from spending extra time locating a replacement in case
they lose one during installation.
1
QUANITY
Rear Duct
1
Bottom Duct
1
Trim Kit
1
Frame
Rail
2
15 required
Short Screws
1 extra
Long Wood
Screws
4 required
2 extra

Advertisement

Table of Contents
loading

Summary of Contents for GE JX9152

  • Page 1: Microwave Oven

    Installation Microwave Oven Built-In Trim Kits Instructions JX9152 and JX9153 Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at: GEAppliances.com BEFORE YOU BEGIN PARTS INCLUDED Read these instructions completely and carefully. IMPORTANT • Save these instructions PART QUANITY for local inspector’s use.
  • Page 2: Installation Instructions

    Installation Instructions TOOLS YOU WILL NEED GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk ❒ 2 Phillips Screwdrivers (#1 & #2) of electric shock by providing an escape wire for the electric current.
  • Page 3: Install The Rails

    Installation Instructions 3 INSTALL THE REAR DUCT 1 LOCATE AND INSTALL THE BASE PAN 1. Gently return microwave oven to its upright position. Set Base Pan into the front cabinet microwave oven 2. Remove screw A. cutout and center it right and left. Push back until the front flange is against the cabinet front wall.
  • Page 4 Do not place them in the microwave oven. Replace the house fuse, or close the circuit breaker to restore power at the service panel. DE68-03364A READ CAREFULLY. KEEP THESE INSTRUCTIONS. 49-40762 11-15 GE Printed in China...
  • Page 5: Instrucciones De Instalación

    Instrucciones Kits de Horno Microondas con Terminaciones Incorporadas de Instalación JX827 and JX830 ¿Preguntas? Llame a 800.GE.CARES (800.432.2737) o Visite nuestro sitio web en: GEAppliances.com ❒ ANTES DE COMENZAR PIEZAS INCLUIDAS Lea estas instrucciones en su totalidad y atentamente. PIEZA...
  • Page 6: Herramientas Que Necesitará

    Instrucciones de Instalación HERRAMIENTAS QUE NECESITARÁ ❒ 1 UBIQUE E INSTALE UNA OLLA DE LA BASE ❒ 2 Destornilladores Phillips (nº 1 y nº 2)) Coloque la Olla de la Base en la abertura del gabinete frontal del horno microondas y centre la misma sobre la derecha y la izquierda.
  • Page 7 Instrucciones de Instalación ❒ 2 INSTALACIÓN DE LOS RIELES ❒ 4 CONTROL DE LA NIVELACIÓN Desconecte el horno microondas del receptáculo. Retire Controle la nivelación colocando un nivel en el frente y todo lo que haya dentro del horno microondas, incluyendo los costados del horno microondas.
  • Page 8 No ajuste en exceso los tornillos, ya que esto podrá ocasionar desalineaciones de las tiras superiores/ laterales. Screw B Tornillo A DE68-03364A 49-40762 03-16 GE LEA DETENIDAMENTE. CONSERVE ESTAS INSTRUCCIONES. Impreso en China...

Table of Contents