Installation Instructions Questions? Call 800.GE.CARES (800.432.2737) BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT – • instructions for local inspector’s use. IMPORTANT – • governing codes and ordinances. Note to Installer – • Be sure to leave these instructions with the Consumer.
Attach Mounting Plate to Wall ...19 Preparation of Top Cabinet ...19 Check Microwave Assembly ...20 Adapting Microwave Blower for Recirculation ...20, 21 Mount the Microwave Oven ...21, 22 Installing the Charcoal Filter ...22 Before You Use Your Microwave ... 23...
15- to 20- ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical...
HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation.
Installation Instructions NOTE: If you need to install ducts, note that the total ″ x 10″ rectangular or 6″ diameter duct length of 3 ⁄ round duct should not exceed 140 equivalent feet. Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully.
Installation Instructions DAMAGE – SHIPMENT/ INSTALLATION • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.
• This microwave oven is for installation over ranges up to 36″ wide. • If you are going to vent your microwave oven to the outside, see Hood Exhaust Section for exhaust duct preparation. • When installing the microwave oven beneath...
Then place a mark halfway between the edges. The center of any adjacent studs should be 16″ or 24″ from this mark. Draw a line down the center of the studs. THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.
Mounting Plate Tabs Touching the Cabinet Bottom Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level. Mounting Plate with Tabs Below Cabinet THE MICROWAVE MUST BE LEVEL.
It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside. Drill holes on the circles. If there is a stud, drill a hole for wood screws.
INSTALLATION TYPES This microwave oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-Vented Ductless) OUTSIDE TOP EXHAUST (VERTICAL DUCT) See page 12...
OUTSIDE TOP EXHAUST INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Check Damper Operation A4. Mount Microwave Oven A5. Adjust Exhaust Adaptor A6. Connect Ductwork ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts.
(absent on models shipped Blower Plate for recirculation exhaust) • Place the microwave in its upright position, with the top of the unit facing up. • This microwave oven may be shipped assembled for top exhaust (adaptor installed) or for recirculation exhaust (adaptor absent).
OVEN (cont.) Cabinet Front Cabinet Bottom Shelf Self-Aligning Screw Microwave Oven Top 4 Attach the microwave oven to the top cabinet. Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Tighten the outer two screws to the top of the microwave oven.
Cut the opening, following the instructions of the REAR WALL TEMPLATE. (Horizontal Duct) REMOVE EXHAUST ADAPTOR This microwave oven is shipped assembled for top exhaust. You will need the exhaust adaptor for installation in the rear wall opening. To remove the exhaust adaptor from the microwave oven: Remove tape securing damper.
Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST 1 Remove and save screw that holds blower motor to microwave.
Page 17
Installation Instructions ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST (cont.) Roll the blower unit 90° so that fan blade openings are facing the front of the microwave. Before Rolling Back of Microwave Gently slip the wire through the gap between the two tabs on the top of the blower so the wire is behind the tabs.
Page 18
Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) Install grease filters. See the Owner’s Manual packed with the microwave.
C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Microwave Assembly C4. Adjust Blower C5. Mount the Microwave Oven C6. Install Charcoal Filter ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts.
Exhaust Adaptor (absent on models shipped for recirculation exhaust) • Place the microwave in its upright position, with the top of the unit facing up. • The microwave oven may be shipped assembled for top exhaust (adaptor installed) or for recirculation exhaust (adaptor absent).
RECIRCULATION (cont.) Guide the wire down into the blower opening so it rests securely in front of the blower. Secure blower unit to microwave with the screw removed in Step 4. Replace blower plate with the screw removed in Step 1.
Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) Install grease filters. See the Owner’s Manual packed with the microwave.
BEFORE YOU USE YOUR MICROWAVE Make sure the microwave oven has been installed according to instructions. Remove all packing material from the microwave oven. Install turntable and ring in cavity. Replace house fuse or turn breaker back on. Plug power cord into a dedicated 15- to 20-amp electrical outlet.
Page 24
164D3370P263 49-40330 03-03 JR Printed in Korea...
Instrucciones de instalación ¿Preguntas? Llame 800.GE.CARES (800.432.2737) ANTES DE EMPEZAR Lea estas instrucciones completa y cuidadosamente. IMPORTANTE – • instrucciones para el uso del inspector local. IMPORTANTE – • todos los códigos y ordenanzas gubernamentales. Nota para el instalador –...
Page 26
Instrucciones de instalación CONTENIDO Información general Instrucciones de seguridad importantes ... 3 Requisitos eléctricos ... 3 Campana de escape... 4, 5 Daños – Envío / Instalación ... 6 Partes incluidas ... 6 Herramientas que necesitará... 7 Espacio de montaje ... 7 Guía de instalación paso por paso Cómo colocar el plato de montaje ...8–10 Cómo remover el plato de montaje...8...
Instrucciones de instalación INSTRUCCIONES DE SEGURIDAD IMPORTANTES Este producto requiere un tomacorriente eléctrico de tres patas conectado a tierra. El instalador debe llevar a cabo una inspección de continuidad a tierra en la caja eléctrica antes de comenzar la instalación para asegurar que la caja tomacorriente está...
Instrucciones de instalación CAMPANA DE ESCAPE NOTA: Lea las siguientes dos páginas solamente si planea ventilar el escape hacia el exterior. Si por el contrario planea recircular el aire de vuelta hacia el salón, continúe en la página 6. ESCAPE SUPERIOR EXTERNO (EJEMPLO SOLAMENTE) La siguiente tabla describe un ejemplo de una posible instalación de red de conductos.
Page 29
Instrucciones de instalación NOTA: Si usted necesita instalar conductos, tenga pendiente que la longitud total del conducto rectangular ″ x 10″ o el conducto redondo de 6″ de diámetro de 3 ⁄ no debe sobrepasar 140 pies equivalentes. La ventilación externa requiere un CONDUCTO DE CAMPANA DE ESCAPE.
Instrucciones de instalación DAÑOS – ENVÍO / INSTALACIÓN • Si la unidad se daña durante el envío, devuelva la unidad al almacén donde la adquirió para su reparación o reemplazo. • Si el cliente daña la unidad, la reparación o el reemplazo es responsabilidad del cliente.
Instrucciones de instalación HERRAMIENTAS QUE NECESITARÁ Destornilladores de estrella # 1 y # 2 Tijeras para cortar latón (para cortar el regulador Tijeras (para cortar la de tiro, si es necesario) plantilla, si es necesario) Guantes Sierra (de sable, agujero, o de ojo de cerradura) Gafas de seguridad ESPACIO DE MONTAJE...
Instrucciones de instalación CÓMO COLOCAR EL PLATO DE MONTAJE CÓMO REMOVER EL HORNO MICROONDAS DEL EMBALAJE / CÓMO REMOVER EL PLATO DE MONTAJE Remueva las instrucciones de instalación, los filtros, la bandeja de cristal, y la bolsa pequeña del equipo. No remueva el protector frontal de espuma de poliestireno del horno.
Page 33
Instrucciones de instalación CÓMO DETERMINAR LA LOCALIZACIÓN DEL PLATO DE MONTAJE DEBAJO DE SU GABINETE Posición del plato – debajo de gabinetes de fondo plano Posición del plato – debajo de gabinetes de fondo apoyado con frente saliente Posición del plato – debajo de gabinetes de fondo apoyado en un marco Las orejillas del plato de montaje tocan el fondo...
Page 34
Instrucciones de instalación CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED Agujero A PRECAUCIÓN: Use guantes de protección para evitar cortaduras en sus dedos con los extremos filosos. Trace una línea vertical en la pared en el centro del espacio de 30″...
Instrucciones de instalación TIPOS DE INSTALACIÓN Este horno microondas está diseñado para adaptarse a los siguientes tres tipos de ventilación: A. Escape superior exterior (Conducto vertical) B. Escape posterior exterior (Conducto horizontal) C. Recirculación (Sin conducto de ventilación) ESCAPE SUPERIOR EXTERIOR (CONDUCTO VERTICAL) Ver página 12 Ver página 19...
Instrucciones de instalación ESCAPE SUPERIOR EXTERIOR PERSPECTIVA GENERAL DE LA INSTALACIÓN A1. Como adherir el plato de montaje a la pared A2. Prepare el gabinete superior A3. Inspeccione la operación del regulador de tiro. A4. Monte el horno microondas A5. Ajuste el adaptador de escape A6.
Instrucciones de instalación USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE Deberá perforar agujeros para los tornillos de apoyo superiores, un agujero suficientemente grande para que el cable eléctrico quepa, y un recorte lo suficientemente grande como para que el adaptador de escape pueda ser introducido.
Instrucciones de instalación CÓMO MONTAR EL HORNO MICROONDAS (continuación) Frente del gabinete Estante del fondo del gabinete Tornillo autoalineable Parte superior del horno microondas Pegue el horno microondas a la parte superior del gabinete. Inserte 2 tornillos autoalineables a través de los agujeros exteriores superiores del horno.
Instrucciones de instalación ESCAPE POSTERIOR EXTERNO PERSPECTIVA GENERAL DE LA INSTALACIÓN B1. Prepare la pared posterior B2. Remueva el adaptador de escape B3. Pegue el plato de montaje a la pared B4. Prepare el gabinete superior B5. Ajuste el calefactor B6.
Instrucciones de instalación CÓMO ADHERIR EL PLATO DE MONTAJE A LA PARED Pegue el plato a la pared usando los tornillos basculantes. Por lo menos un tornillo de madera debe ser usado para pegar el plato al poste de viga de la pared. Remueva las mariposas de los tornillos.
Page 41
Instrucciones de instalación CÓMO ADAPTAR EL CALEFACTOR DEL MICROONDAS PARA EL ESCAPE EXTERIOR Ruede la unidad del calefactor 90° de forma tal que las aberturas de la paleta del ventilador estén orientadas hacia la parte frente del horno microondas. Antes de la rotación Después de la rotación Parte posterior del horno microondas...
Instrucciones de instalación CÓMO MONTAR EL HORNO MICROONDAS PARA OBTENER UNA INSTALACIÓN MÁS FÁCIL Y EN POS DE LA SEGURIDAD PERSONAL, SE RECOMIENDA QUE DOS PERSONAS INSTALEN ESTE HORNO MICROONDAS. IMPORTANTE: No agarre ni use la manija de la puerta durante la instalación. NOTA: Si su gabinete es de metal, use la arandela de nilón alrededor del cable eléctrico para evitar que el mismo sea cortado.
Instrucciones de instalación RECIRCULACIÓN PERSPECTIVA GENERAL DE LA INSTALACIÓN C1. Pegue el plato de montaje a la pared C2. Prepare el gabinete superior C3. Inspeccione la ensambladura del microondas C4. Ajuste el calefactor C5. Monte el horno microondas C6. Instale el filtro de carbonilla CÓMO ADHERIR LA PLACA DE MONTAJE A LA PARED Pegue el plato a la pared usando los tornillos...
Instrucciones de instalación INSPECCIONE LA ENSAMBLADURA DEL MICROONDAS Adaptador de escape (ausente en los modelos enviados con escape de recirculación) • Coloque el horno microondas en su posición vertical, con la parte superior hacia arriba. • Este horno microondas puede ser enviado ensamblado para uso con tubo de escape en la parte superior (con adaptador ya instalado) o con tubo de escape de recirculación (adaptador ausente)
Instrucciones de instalación CÓMO ADAPTAR EL CALEFACTOR DEL MICROONDAS PARA LA RECIRCULACIÓN (continuación) Guíe el alambre hacia abajo en la abertura del soplador de forma que descanse con seguridad en el frente del soplador. Coloque la unidad en el microondas con el tornillo removido en el Paso 4.
Instrucciones de instalación CÓMO MONTAR EL HORNO MICROONDAS (continuación) Inserte 2 tornillos autoalineables a través de los agujeros exteriores superiores del horno. Gire dos vueltas completas en cada tornillo. Apriete el tornillo del centro completamente. Apriete los dos tornillos exteriores hacia la parte de arriba del horno microondas.
Instrucciones de instalación ANTES DE COMENZAR A USAR SU HORNO MICROONDAS Cerciórese de que el horno ha sido instalado de acuerdo con las instrucciones. Remueva todos los materiales de embalaje del horno microondas. Instale el aro rotatorio y con ruedas en la cavidad.
Page 48
164D3370P263 49-40330 03-03 JR Impreso en Corea...
Need help?
Do you have a question about the JVM2070BH and is the answer not in the manual?
Questions and answers