MaxiiCopper Vi2400WP Installation Manual

Vi2400WP Ethernet Extender over UTP Installation Manual
The MaxiiCopper Model Vi2400WP is a transmission device with IP67
weather proof packaging that extends full-duplex high-speed Ethernet and
PoE over existing Coax infrastructures. It extends 10BaseT signals up to
3,000 feet (914m) and 100BaseT up to 1,500 feet (457m). It employs
MaxiiCopper innovative and unique Ethernet extension technology that is
designed to take full advantage of high-bandwidth networking cables and
maintain a full-duplex of 10 or 100 Mb/s Ethernet connection up to the
maximum range with minimum transmission error and latency.
Pass Through PoE (PTP™) eliminates the need for additional remote site
power while allowing a single PoE source, such as a PoE network switch, to
provide power to both transceivers and the camera. This feature eliminates
the need for local and remote site power supplies. The Vi2400WP is type
tested under NEMA-TS2 environmental standards for extended temperature
operations between -40C° to +75C°, the Vi2400WP is the perfect solution
for extended distance data and power transmission for warehouses, parking
lots, campuses, casinos, and many more.
Installation cost savings, proven performance, and major camera brand
compatibility all go into making Vigitron's MaxiiCopper™ Vi2400WP your
best choice for extended distance data and power transmission.
Important Safety Warning
- Read and keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer's instructions.
- This installation should be made by a qualified service person and should conform to all local
codes.
- DO NOT bundle UTP or Coax signals in the same conduit as high-voltage wiring.
- To reduce the risk of fire or electrical shock, do not expose these products to rain, moisture,
dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron equipment.
- DO NOT install the unit in a place where the operating ambient temperature exceeds 75°C or
is below - 40°C.
- Make sure that the external power supply output voltage is in the recommended range.
- Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus that produce heat.
- Protect the power cord from being walked on or pinched particularly at power source,
convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when a power supply cord or plug is damaged, liquid
has been spilled, objects have fallen inside the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
- The main plug is used as the disconnect device and shall remain readily operable.
RISK OF ELECTRIC SHOCK
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
DO NOT OPEN
The Smart Choice for Transmission Solutions
WARNING! - To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture. This apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases shall be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must be connected to a
mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and shall remain readily
operable.
Application Drawing
Transmitting Ethernet and PoE over Extended Coax Cables
Vi2400WP
Vi2400A
Vi2400WP
Data + PoE
328 ft. (100m)
Network Switch
IP Camera-end Installation
Standard Ethernet Connection:
The Vi2400WP need to be powered by PoE from the control room side.
- Connect the IP camera RJ45 connector to the "Standard Ethernet" port
of Vi2400WP using a standard Cat5/6 cable of maximum 100m in length.
- Connect one end of the UTP cable to the "Standard Ethernet"
waterproof RJ45 connector of Vi2400WP.
In order to connect wires to the weatherproof connectors:
a- Unscrew the gasket and insert the UTP cable checking to confirm there is
no spacing between the wire and the insertion hole.
b- Connect the RJ45 cable and insert it into the RJ45 female connector on
the Vi2400WP's body making certain the connection is tight.
c- Reconnect the gasket by screwing into the Vi2400WP body making certain
to limit any wire slack.
Extended Ethernet Connection:
- Connect one end of the long Coax to waterproof BNC connector of the
"extended Ethernet" port on Vi2400WP.
In order to connect wires to the weatherproff connectors:
a- Unscrew the gasket and insert the Coax cable checking to confirm there is
no spacing between the wire and the insertion hole.
b- Connect the BNC connector and insert it into the Coax female connector
on the Vi2400WP's body making certain the connection is tight.
c- Reconnect the gasket by screwing into the Vi2400WP body making certain
to limit any wire slack. limit any wire slack.
Ethernet Switch/Midspan-end Installation
The other end of long Coax cable can be connected to several different
Vigitron Extenders. Please follow the installation guide for the selected
device.
Maxii Copper
Data +
328 ft. (100m)
Vi2400A
Data + PoE
Extended Coax
Vi2400WP
Data +
Data + PoE
328 ft. (100m)
Extended Coax
Vi2400WP
Data + PoE Data +
Extended Coax 328 ft. (100m)
www.vigitron.com
TM
PoE
PoE Cameras
PoE
PoE Cameras
PoE
Vi2400WP_UM