GE Profile PDWT502RII Dimensions And Installation Information page 2

PDWT502RII
GE Profile Dishwasher with SmartDispense
™
Custom Dishwasher Door Panel Template
GE Pub. No. 031-30569-1
Order GE Pub. No. 031-30569-1
Call 1-800-626-2000
For a full-size panel template with complete
panel installation instructions.
For answers to your Monogram, GE Profile
®
GE appliance questions, visit our website at
®
ge.com or call GE Answer Center service,
®
800.626.2000.
For Reference Only
Not to Scale
or
™
Technology
™
Trim Around Dotted Line
2-9/32 "
Drill 3/32"
Pilot Hole
3/32" Deep
3/4" Thick Custom Panel
Te mplate Instructions for
Top Control Integrated Pro le and
Monogram Dishwasher Models
The custom panel should be sized to your installation situation. See Step 1. For easier
installation the custom panel and custom handle should be attached before installing the
dishwasher . Use this template to locate mounting screws and spacers on the custom panel.
IMPO RT ANT
• A custom handle must be installed onto the custom
panel. Install the custom handle 4-1/2" max. from
the top of the panel.
STEP 1 CUSTOM P
HEIGHT
Panel height must be between 30-1/16" and 30-1/4".
23-3/4"
• If the panel height is more than 30-1/4" it will
prevent the door from swinging open.
• If the panel height is less than 30-1/16" it will not
cover the dishwasher door frame.
25-9/16"
STEP 2 DRA W CENTERLINE
• Place the custom panel on a at surface with appearance side
down.
• Locate the vertical center of the panel at the top.
• Use a carpenters square to draw a centerline from top to bott om.
STEP 3 ALIGN TEMPLA
• Trim template on the dotted line along all sides.
• Place the template on the panel aligned with the top edge and
the centerline. Use tape to hold in place.
IMPORTANT: If the template is not aligned with the top edge of the
panel, the 1/2" minimum gap will not be maintained. This 1/2" minimum
gap must be maintained to prevent condensation and damage to the
control panel from screw heads.
• Use an awl to mark the screw hole locations indicated on the
template. Remove the template.
STEP 4 INST ALL MOUNTING SCREWS AND SP
If the panel is less than 3/4" thick, shorter screws mus t
be used. Use #8 x 1/2" screws for 1/2" thick panels (not suppli
• Use a 3/32" drill bit to drill pilot holes 3/32" deep in the
locations.
Note: The custom panel is secured to the dishwasher door with
the spacers and screws provided. The spacer will slip into the
keyhole slots on the dishwasher door .
• Drive the supplied #8 x 5/8" Phillips truss head steel screws
through the spacer and into the panel.
• Install remaining spacers and screws as indicated in the mark e d
locations.
Drill 3/32"
Pilot Hole
3/32" Deep
Trim Around Dotted Line
Top of Panel
11-5/16"
STEP 5 INST ALL CUSTOM HANDLE
A custom handle must be installed onto the panel
before the panel is secured to the dishwasher door .
• The handle should be installed so that it aligns with
adjacent drawer handles, or 4-1/2" max. from the
top of the panel. Secure the handle in the same
manner as cabinet handles. Screws must be
countersunk into the panel.
STEP 6 INST ALL ASSEMBLED P
• Secure the panel to the door by inserting the top
and bottom mounting screws with spacers into
the matching keyhole slots.
• Make sure all 4 spacers engage the keyhole slots.
PA RT S INCLUDED : • Press the panel against the door and push
(4) Spacers downward until the spacers are fully engaged
(4) #8 x 5/8" Phillips truss head stainless steel screws
into the key hole slots. The panel should align
(3) #8 x 1-3/4" Phillips truss head stainless steel
evenly with the top and sides.
wood screw s
(2) Heavy duty spring s
ANEL SIZE REQUIREMENTS
• The top of the custom panel must be ush
with the top of the door . The 1/2" minimum gap
between the top of the door and the bottom of the
countertop must be maintained.
Countertop
• Stand the dishwasher upright.
30-1/16" Min. • Open dishwasher door and drive the supplied
30-1/4" Max.
#8 x 1-3/4" truss head screws. Drive one screw at
1/2" min.
the top and one on each side as shown, through
the inner door and into the custom panel.
Minimum 1/2" Gap
for Clearanc e
WIDTH WARNING: Do not overtighten screws. Excessive
tightening of the screws could damage door edges.
Panel width must be 23-3/4".
• If the panel width is less than 23-3/4" it will not
cover the dishwasher frame.
IMPORTANT: To ensure optimum door balance
performance, the custom panel must not weigh more
than 14 lbs.
STEP 7 INST ALL DOOR SPRINGS
The dishwasher is shipped from the factory with a
temporary set of balance springs. Use the heavy duty
springs provided and the adjustment holes in the
cable to balance the door after the custom panel
is installed onto the dishwasher .
TE TO P ANEL • With the dishwasher on the wood skid, close an d
latch the door .
• Remove and discard both door springs .
• Attach the new heavy duty door springs. Engag e
the end with the short hook into the support leg
and the long hook into the cable.
• Open and close the door .
Mark Center • If the door drops open when released, increase
Screw Holes
spring tension. If the door closes when released,
decrease tension.
ACERS
ed).
marked
Screw
Spacer
Listed by
Underwriters
Laboratories
Specification Created 6/09
Top of Panel
Trim Around Dotted Line
2-9/32 "
11-5/16"
Drill 3/32"
Pilot Hole
3/32" Deep
Screws Must
Be Countersunk
Into Panel
4-1/2" Max.
From Top
of Panel
Handle
Custom
Door Panel
ANEL
Custom
Panel
Dishwasher
Door
Shoulder Washers
Engage Keyhole
Slots
Custom
Panel
25-9/16"
Use This
Mounting
Hole
Pulley
Decrease
Tension
Shoulder
Increase
Correct Spring
Tension
Cable Routing
TIP: If the door does not open easily or falls too
quickly, check spring cable routing. The cable is held
in place by "shoulders" on the pulley . Check to be
sure the cable has not slipped over the pulley
shoulders.
IMPOR TA NT : Adjust both balance springs to the
same amount of tension to prevent excessive door
twisting during use.
Drill 3/32"
Pilot Hole
3/32" Deep
Trim Around Dotted Line
As an ENERGY ST AR
®
partner, GE has determined
that this product meets the
ENERGY ST AR guidelines
for energy e ciency.
250230