VonHaus 3515387 Instruction Manual

VonHaus 3515387 Instruction Manual

800w paint station

Advertisement

800W PAINT
STATION
3515387 - Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3515387 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for VonHaus 3515387

  • Page 1 800W PAINT STATION 3515387 - Instruction Manual...
  • Page 2 CONTENTS Safety Instructions Safety Instructions. Safety Warnings Specification Material Preparation/Thinning Chart Operation Aligning the Suction Tube/Surface Preparation...
  • Page 3 Spray Technique Spray Pattern Adjustment/Material Flow Adjustment Cleaning & Maintenance Removing the Air Filter Troubleshooting Warranty...
  • Page 4 WARNING PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE INTENDED USE. such as in the presence of flammable Only use the Paint Station as described in liquids, gases or dust. this instruction manual. Keep bystanders, children and animals This Paint Station it is not suitable for away while operating the product.
  • Page 5: Safety Symbols

    WARNING PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE STORAGE & MAINTENANCE. or trip hazard. NEVER, under any circumstances, point Store the product out of reach of children the Paint Station at another person or and do not allow persons unfamiliar animal.
  • Page 6: Specification

    SPECIFICATION INPUT PAINT VOLTAGE FREQUENCY POWER CONTAINER VISCOSITY DIN-S 1200 220 - 240 50/60 On/Off Switch (see page 5) Spray Pattern Adjuster Shoulder Strap Nozzle Cleaning Needle Locking Nut Cleaning Brush Air Hose Viscosity Cup Spray Gun Suction Tube Max. Paint Volume Control Air Filter Trigger Container...
  • Page 7: Material Preparation

    MATERIAL PREPARATION IMPORTANT Before spraying, the material being used may need to be thinned with solvent; as specified by the material manufacturer. WARNING Do not use materials with a flashpoint below 39°C. NOTE Follow the instructions below. Stir the spraying material thoroughly before measuring viscosity.
  • Page 8: Operation

    OPERATION Attach the tilted end of AIR HOSE (4) into the back of the SPRAY GUN (5). Attach the opposite end of the AIR HOSE (4) into the slot at the base of the MOTOR UNIT (9). NOTE This has two lugs to align and twist clockwise to secure into position.
  • Page 9: Aligning The Suction Tube

    ALIGNING THE SUCTION TUBE Unscrew the CONTAINER (8) from the SPRAY GUN (5) and rotate the SUCTION TUBE (15) to the correct position. If you are going to be spraying in a downward direction, the angled end of the SUCTION TUBE (15) should be pointing towards the front of the Spray Gun.
  • Page 10: Spray Technique

    SPRAY TECHNIQUE Spray parallel to the surface with smooth passes at a consistent speed as illustrated below. Adhering to this ADVISORY If spraying with an HVLP spray will avoid irregularities in the final finish. system is new or unfamiliar to you, it is strongly advisable to practice on a piece of Always apply a thin coat of material on the first pass cardboard or wood offcuts before proceeding...
  • Page 11: Spray Pattern Adjustment

    SPRAY PATTERN ADJUSTMENT The spray pattern shape is adjusted by rotating The positions of the SPRAY PATTERN ADJUSTER the SPRAY PATTERN ADJUSTER (1) to either the (1) and corresponding spray pattern shapes are vertical, horizontal or diagonal positions. illustrated below. Loosen the LOCKING NUT (3) sufficiently to enable Test each pattern and use whichever pattern is you to rotate the SPRAY PATTERN ADJUSTER (1).
  • Page 12: Cleaning And Maintenance

    CLEANING & MAINTENANCE Spray again for 2 seconds. Unplug the paint station NOTE Always flush the spray outdoors. from the mains and trigger the gun so that the material inside the spray gun flows back into the Area must be free of flammable vapours. container.
  • Page 13: Removing The Air Filter

    REMOVING THE AIR FILTER The AIR FILTER (16) should be cleaned on a regular basis to ensure the optimal performance of the paint station is maintained. Squeeze both clips either ends of the air filter cover and remove the sponge inside. IMPORTANT Clean the sponge with warm soapy water and allow to dry for at least 24 hours before replacing the sponge back into...
  • Page 14: Troubleshooting

    TROUBLESHOOTING PROBLEM CAUSE SOLUTION 1. Nozzle clogged 1. Clean 2. Suction tube clogged 2. Clean LITTLE OR NO PAINT FLOW 3. Suction tube loose 3. Insert 4. No pressure build up 4. Tighten container 5. Air Filter clogged 5. Change 1.
  • Page 15: Disposal Information

    5th Floor The Tower Deva City Office Park Manchester M3 7BF Declare under our sole responsibility that the product: SKU: 3515387 Description: VonHaus 800W Paint Station To which this declaration relates is in conformity with the following directives: 2006/42/EC, 2014/30/EU, 2011/65/EU...
  • Page 16 Thank you for purchasing the 800W Paint Station. VonHaus is a registered trademark of DOMU Brands Ltd ® Made in China for DOMU Brands Ltd M24 2RW...

Table of Contents