Download Print this page

Advertisement

Quick Links

Model No. GLSY22521
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
Patent Pending

Advertisement

loading
Need help?

Need help?

Do you have a question about the GLSY22521 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Tracker GLSY22521

  • Page 1 Model No. GLSY22521 Serial No. Write the serial number in the USER’S MANUAL space above for future reference. Serial Number Decal (Under Seat) QUESTIONS? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or if there are...
  • Page 2: Table Of Contents

    Decal 1 Keep hands and Decal 2– fingers clear of This decal is on the finger guards this area. on both sides of the weight bench. TRACKER, a registered trademark of Galyan’s Nevada Inc., East Main St., Plainfield, IN 46168...
  • Page 3: Important Precautions

    IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system. 1. Read all instructions in this manual before 10. Always set both safety spotters at the same using the weight system. Use the weight sys- height.
  • Page 4: Before You Begin

    The model shapely figure, dramatic increase in muscle size and number is GLSY22521. The serial number can be strength, or a healthier cardiovascular system, the 735 found on a decal attached to the weight system (see POWER SMITH SYSTEM weight system will help you the front cover of this manual).
  • Page 5: Assembly

    ASSEMBLY • As you assemble the weight system, make sure Make Things Easier for Yourself all parts are oriented as shown in the drawings. Everything in this manual is designed to ensure • For help identifying small parts, use the PART that the weight system can be assembled suc- IDENTIFICATION CHART.
  • Page 6 3. Press two Bushings (34) into the Bench Frame (2). Attach the Bench Frame (2) to the Front Leg (4) with four M10 x 94mm Bolts (18), two Joint Plates (39), and four M10 Nylon Locknuts (32). Do not tighten the Locknuts yet. 4.
  • Page 7 6. Press four Bushings (34) into the Backrest Frames (6) as shown. Secure the Backrest Knob (25) to the Bench Frame (2). Pull the Knob out as far as it will go. Slide the Backrest Bracket (9) between the Bench Frame tubes and engage the Knob into a hole in the Bracket.
  • Page 8 9. Press three 50mm Square Inner Caps (88) into the Leg Lever (7). Press a 51mm Round Inner Cap (23) into the tube on the Leg Lever. Slide the two Pad Tubes (16) into the Leg Lever (7). Slide four Foam Pads (17) onto the ends of the Pad Tubes.
  • Page 9 12. Locate the Base (49) with the warning decal attached to it. Attach two Base Feet (71) to the Base with four M4 x 16mm Screws (103). Attach the Base (49) to the indicated side of the Center Base (48) with two M10 x 78mm Bolts (40), two M10 Washers (100), and two M10 Nylon Locknuts (32).
  • Page 10 14. See the inset drawing. Insert an M10 x 19mm Bolt (111) into the bracket on the Weight Carriage (55). The front edge is taller than Press two 51mm Round Inner Caps (23) into the the rear edge Weight Carriage (55). Orient the Weight Carriage (55) and Lat Tower (43) as shown.
  • Page 11 16. Press two 38mm Bushings (74) into the Left Weight Glider (62). Attach the Left Spotter Hook (76) to a Safety Spotter (64) with an M10 x 25mm Bolt (105) and an M10 Nylon Locknut (32). Do not overtighten the Locknut; the Spotter Hook must be able to pivot easily.
  • Page 12 19. Press two 50mm Square Inner Caps (88) into the ends of the Pulley Bar (47). Attach the Pulley Bar (47) inside the Lat Tower (43) with two M10 x 68mm Bolts (26), four M10 Washers (100), and two M10 Nylon Locknuts (32).
  • Page 13 22. Route the Medium Cable (94) over an 89mm Pulley (90) and down through the Pulley Bar (47). Attach the Pulley inside the Pulley Bar with an M10 x 68mm Bolt (26), two M10 Washers (100), two 12mm Spacers (110), and an M10 Nylon Locknut (32).
  • Page 14 26. Wrap the Short Cable (95) around a “V”-Pulley (91). Attach the Pulley and a Large Cable Trap (92) to the bracket on the Rear Upright (46) with an M10 x 60mm Bolt (101) and an M10 Nylon Locknut (32). 27.
  • Page 15 30. Pull the Short Cable (95) down between the two “V”-Pulleys (91). Hold an 89mm Pulley (90) inside the Cable and attach it to the Double “U”-Bracket (78) with an M10 x 45mm Bolt (27) and an M10 Nylon Locknut (32). Wrap the Long Cable (96) around an 89mm Pulley (90).
  • Page 16 34. Slide the Barbell (61) through the Left Weight Glider (62), the Locking Bar (58), and the Right Weight Glider (63). Make sure the Locking Bar is oriented as shown. Turn the Locking Bar (58) so that the hooks engage slots in the Uprights (not shown). 35.
  • Page 17: Adjustments

    ADJUSTMENTS This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the cor- rect form for each exercise. Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediate- ly.
  • Page 18 USING THE LOCKING BAR AND SAFETY SPOTTERS Before starting an exercise, position the Locking Bar (58) and the Safety Spotters (64) in the correct posi- tion for that exercise. To do this, grip the Locking Bar (58) with both hands. Turn the Locking Bar until the two hooks disengage the slots in the Uprights (42).
  • Page 19 USING THE BUTTERFLY ARMS To use the Butterfly Arms (56, 57), place the weight bench, with the Backrest (10) in the level position (see ADJUSTING THE BACKREST on page 17), next to the Rear Upright (46). Place the desired amount of weight on the Weight Carriage (55) (see ADDING WEIGHT TO THE WEIGHT RACK on the previous page.)
  • Page 20 PART IDENTIFICATION CHART—Model No. GLSY22521 R0103A M10 x 68mm Bolt (26) M10 x 19mm Bolt (111) M10 x 75mm Carriage Bolt (102) M10 x 25mm Bolt (105) M10 x 75mm Bolt (30) M10 x 45mm Bolt (27) M10 x 78mm Bolt (40)
  • Page 21 M4 x 16mm Screw (103) M8 Nylon Locknut (81) M6 x 63mm Screw (104) M10 Nylon Locknut (32) M8 x 19mm Screw (107) M6 x 16mm Bolt (31) M6 x 53mm Bolt (29) M13 x 25mm Screw (113) M8 x 70mm Bolt (108) M6 Washer (37) M10 Washer (100) M8 x 21mm Shoulder Bolt (114)
  • Page 22 19mm Round Inner Cap (19) 20mm x 40mm Inner Cap (20) 25mm Round Outer Cap (99) 38mm x 50mm Inner Cap (112) 51mm Round Inner Cap (23) 45mm Square Inner Cap (80) 60mm Square Inner Cap (82) 50mm Square Inner Cap (88) 51mm x 76mm Inner Cap (21)
  • Page 23 PART LIST—Model No. GLSY22521 R0103A No. Qty. Description No. Qty. Description No. Qty. Description Rear Stabilizer Lat Tower Chain Bench Frame Rear Base Handle Front Stabilizer Foot Plate Large Weight Clip Front Leg Rear Upright Large Weight Clip Seat Frame...
  • Page 24 EXPLODED DRAWING—Model No. GLSY22521 R0103A...
  • Page 25 REMOVE THIS PART IDENTIFICATION CHART AND PART LIST/ EXPLODED DRAWING. SAVE THIS PART IDENTIFICATION CHART AND PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE.
  • Page 26: Ordering Replacement Parts

    Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the following information when calling: • The MODEL NUMBER of the product (GLSY22521) • The NAME of the product (TRACKER ®...