Advertisement
Quick Links
LED Light and Wireless Hour Meter Harness Kit
2012 and After Greensmaster
2100 Series Mower
Model No. 04295
Contact your Authorized Toro Distributor for more information.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of
Conformity (DOC) sheet.
This product contains a chemical or chemicals known to the State of California to
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
No parts required
Flange head screw
Voltage regulator
Mounting bracket
Wire harness
Cable tie
Rocker switch
No parts required
No parts required
Register at www.Toro.com.
®
800, 1000, 1600, Flex
WARNING
CALIFORNIA
Qty.
–
–
2
1
1
1
2
1
–
–
Form No. 3401-934 Rev A
™
Installation Instructions
Use
Prepare the machine.
Remove the control-panel cover (1800
or 2100 series machines).
Assemble the voltage regulator.
Route the wire harness.
Connect the wire harness.
Finish the LED light and wireless hour
meter harness kit installation.
Install the wire harness to the LED light
kit and/or wireless hour meter kit.
Original Instructions (EN)
All Rights Reserved *3401-934* A
Printed in the USA
1800, or
Advertisement
Related Manuals for Toro 04295
Summary of Contents for Toro 04295
- Page 1 1800, or 2100 Series Mower Model No. 04295 Installation Instructions Contact your Authorized Toro Distributor for more information. This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING...
- Page 2 Preparing an 1800 or 2100 Series Machine 1. Ensure the traction and reel drive engagement lever is in the position; refer to the Operator’s REEL DRIVE Preparing the Machine Manual. 2. Move the machine to a level surface and set the No Parts Required traction and reel drive engagement lever to the position;...
- Page 3 Removing the Control-Panel Assembling the Voltage Cover (1800 or 2100 Series Regulator Machines) Parts needed for this procedure: No Parts Required Flange head screw Voltage regulator Procedure Mounting bracket 1. Remove the 4 flange-head screws (1/4 x 1/2 inch) that Wire harness secure the control-panel cover to the support bracket of the handle bar...
- Page 4 Figure 5 2. 3-socket connector 1. 3-pin connector (wire harness) (voltage regulator) Assembling the Voltage Regulator and Mounting Bracket to the Machine Figure 7 1. Prepare the machine for installation of the voltage 1. Cable tie (fir-tree anchor) 4. Stud (fuel tank) regulator and mounting bracket by performing the 2.
- Page 5 2. Align the ground terminal of the wire harness with the left hole short flange of the mounting bracket for the voltage regulator as shown in Figure Routing the Wire Harness Parts needed for this procedure: Cable tie Procedure 1. Route the wire harness from the mounting bracket to the left handlebar (Figure 10 Figure...
- Page 6 Connecting the Wire Harness Parts needed for this procedure: Rocker switch Connecting the Wire Harness to the Engine 1. Locate the engine-alternator harness at the rear side of the engine case (Figure 12). Figure 11 1800 or 2100 Series Machines Note: The engine-alternator harness has 2 wires with single socket connectors.
- Page 7 Identifying the Electrical Connectors • Use the 3-socket connector when installing the optional Wireless-Hour Meter Kit (Figure 13 Figure 14). • Use the 2-socket connector light harness interconnect when installing the optional LED Light Kit (Figure 13 Figure Figure 14 1800 or 2100 Series Machines 1.
- Page 8 Installing the Light Switch (800, 1000, 1600 Series Machines) 1. Remove the knock-out plug at the top left area for the console (A Figure 15). Figure 16 1. Opening (control panel) 3. Notch (body—rocker switch) 2. 2-position rocker switch 4. Left side of the control panel 5.
- Page 9 Installing the Light Switch (1800 or 2100 Series Machines) 1. Remove the plug from the opening at the left face of the control panel (Figure 17). Figure 18 1. Opening (control panel) 3. Notch (body—rocker switch) 2. 2-position rocker switch 4.
- Page 10 Connecting the Spark-Plug Wire Connect the spark-plug wire to the terminal of the spark plug as shown in Figure 2 1 Preparing the Machine (page Finishing the LED Light and Wireless Hour Meter Harness Kit Installation Installing the Wire Harness No Parts Required to the LED Light Kit and/or Wireless Hour Meter Kit...
- Page 11 Notes:...