Sony ILCE-7SM2 Service Manual page 13

2-1-3. MAIN BOARD SECTION
ns: not supplied
#2 F
C
Top Cabinet Section
3
(See page 2-9)
1
107
Grip Cover Section
1
(See page 2-10)
101
4
Mecha Device
A
Section
118
B
(See page 2-6)
CAUTION
For the part of 123: VF Flexible Adhesive Sheet, cut the Adhesive Sheet
(2-649-300-01) into the desired length and use it.
注意
123: VF Flexible Adhesive Sheetは，Adhesive Sheet (2-649-300-01)
を切って使用すること。
Ref. No. Part No. Description
101 X-2591-922-1 BASE ASSY (795), JK
102 4-559-295-01 SHEET, VF FLEXIBLE PROTECTION
104 A-2081-495-A VF BLOCK ASSY (795)
106 A-2075-938-A ES-1002 FLEXIBLE BOARD, COMPLETE
107 4-575-780-01 VF SHEET, RADIATION (795)
108 4-559-171-01 HOLDER, GYRO
109 4-559-173-01 CUSHION, GYRO G
110 A-2064-122-A GY-1008 BOARD, COMPLETE
111 4-559-172-01 CUSHION, GYRO
112 A-2064-121-A GY-1007 BOARD, COMPLETE
113 4-559-168-01 SHEET, N
115 X-2591-924-1 FRAME ASSY (795), SY MAIN
116 A-2084-513-A SY-1063 BOARD, COMPLETE (SERVICE)
117 A-2075-939-A BH-1003 FLEXIBLE BOARD, COMPLETE
118 4-575-770-01 SHEET (795), LIGHT SPACER
ILCE-7SM2_L2
Note 2: Refer to "1-2. NOTES FOR REPLACING THE EVF
DISPLAY DEVICE (LCD902) OR THE SY-1063 BOARD" on
page 1-1.
Note 2: 1-4ページの"1-2. EVF表示素子 （LCD902） またはSY-1063基板
交換時の注意" を参照してください。
LCD902
(Note 2)
2 104
: BT1100 (LITHIUM SECONDARY
ns BATTERY) Board on the mount
position.
(See page 6-55 of Level 3)
102
123
D
(Size 10.6 x 12.0 mm)
When removing and re-assembling,
125
pull this connector vertically from the board.
108
5
#327 106
E
110 6 ANT901
109
#327
ns
113
#1
111
BT1100
(Note 1)
112
117
124 BH1100
#2
(Note 1)
#309
#2
#1
119
121
D
C
120
#1
115
8
116
120 7
A
B
Ref. No. Part No. Description
119 4-575-774-01 SHEET (C (795)), SY RADIATION
120 4-575-775-01 SHEET (D (795)), SY RADIATION
121 4-576-684-01 SHEET (E (795)), SY RADIATION
122 4-576-739-01 GASKET (HD (795))
123 CAUTION SHEET, VF FLEXIBLE ADHESIVE
124 4-578-833-01 SHEET (C (795)), RADIATION (GF)
125 4-579-986-01 SHEET (ES), ELECTROSTATIC
ANT901 A-2066-642-A SOLDERING_NFC BLOCK ASSY
 BH1100 1-251-928-21 SOCKET, BATTERY (Note 1)
 BT1100 1-756-134-16 BATTERY, LITHIUM (SECONDARY) (Note 1)
LCD902 A-2086-296-A ECX331CA-2_SERVICE (Note 2)
#1 2-635-562-11 SCREW (M1.7)
#2 2-635-562-31 SCREW (M1.7)
#309 4-300-115-21 TAPPING (1.7) (CH)
#327 4-300-113-11 TAPPING (1.7) (CH)
DISASSEMBLY
1. Remove in numerical order (
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇: Solder
#309 X 1 → #2 X 1 → Flexible Board (1)
1
Back View
#309
Flexible Board (3-1) → Harness (3-2) → #2 X 3
3
Left View
ns
#327 X 2, #1 X 1
5
F
Back View
E
#327 #327
#1
122
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
1.7
2.5
Note
Note 1: Replace the battery holder (BH1100) together when
replacing the lithium secondary battery (BT1100) on the
BH-1003 flexible board. (The battery holder removed once
cannot be used again.) When mounting these parts, mount
new battery holder first and attach new lithium storage
battery next.
2-5
to ) in the left figure.
1 8
Bottom View
#2
Back View
-1
-2
#2
#1 X 1
7
Left View Back View
#1
#1
#2: M1.7 X 4.0 #309: M1.7 X 5.0 (Tapping) #327: M1.7 X 4.0 (Tapping)
(Black) (Black) (Silver)
4-300-113-11
2-635-562-31 4-300-115-21
1.7 1.7
4.0
5.0
Note 1: BH-1003フレキシブル基板のリチウム蓄電池 （BT1100） を交換
する場合はバッテリホルダ （BH1100） も同時に新品に交換して
ください。
（一度使用したバッテリホルダは再使用できません。 ） 部品取り
付けの際は、先にバッテリホルダを取り付けてからリチウム蓄
電池を装着してください。
Right View
#2
#1 X 4
8
Right View Back View
#1
#1
1.7
4.0