Maintenance - DeWalt X536 Instruction Manual

PRODUCT CARE, cont'd
Oil Chart
Apply a few drops of SAE engine oil, grease, or use a spray lubricant. Apply the oil to
both sides of pivot points. Wipe off any excess. Start engine and operate mower briefly to
insure that oil spreads evenly.
Number of Oil Points Description
4 Deck Suspension Pivots
2 Rear Deck Stabilizer Pivots
4 Height Adjustment Turnbuckle Clevis Pin
2 Height Adjustment Handle Pivots
6 Deck Lift Linkage Pivots
2 Deck Lift Handle Pivots
1 Deck Lift Handle Pin
2 Deck Frame Up-and-Down Pivots
4 Operator's Platform Linkage Pivot Points
4 Speed Control Linkage Rod End Bearings
2 Pump Control Lever Pivots
1 Operator's Platform Suspension Adjustment
Lever Pivot
1 Brake Lever Pivot
1 Brake Lever Pivot Clevis Pin
1 Brake Lever Control Rod Pivot
Hydraulic Fluid
• Shell TT-SB
General Purpose Lubrication:
Use any NLGI grade 2 multi-purpose grease. Shell Albida EP2 is recommended.
Shell Albida EP 2 is a red-colored multi-purpose grease designed for heavy-duty
bearing applications. It has high base oil viscosity for mechanical stability, has been
formulated for high load, low-speed applications, and has excellent lubrication and
corrosion protection.
nOTE: This Operator's Manual covers several models. Mower features may vary by
model. Not all features in this manual are applicable to all mower models and the
mower depicted may differ from yours.

Maintenance

WARNING: Before performing any maintenance or repairs, disengage
the PTO, move the drive control levers in the neutral position and engage
the parking brake. Stop the engine and remove the key to prevent
unintended starting.
Post-Operation Mower Care
After each operation of the mower, the following procedures should be implemented to
extend the life of your mower and ensure safe operating conditions.
WARNING: Failure to follow these recommendations may result in serious
injury to yourself or others and may cause damage to the mower.
Cleaning the Underside of the Deck
Rinse grass clippings from the deck's underside and prevent the buildup of corrosive
chemicals.
WARNING: Make certain the mower's discharge chute is directed AWAY from
people, your house, garage, parked cars, etc.
1. Disengage the PTO, set the parking brake and stop the engine. Use a hose to spray
the underside of the deck.
nOTE: Make sure that the hose is not routed under the deck and is clear of all
moving parts.
2. After cleaning your deck, return to the operator's platform and engage the PTO. Keep
the deck running for a minimum of two minutes, allowing the underside of the deck
to thoroughly dry.
DAILY
WEEKLY
Cleaning the Mower
WARNING: If the mower has been recently run, the engine, muffler and
surrounding metal surfaces will be hot and can cause burns to the skin. Let
the engine cool for at least five minutes. Exercise caution to avoid burns.
Your mower should be cleaned after each use and under certain conditions, i.e. dry
conditions and/or mulching situations, additional cleaning may be necessary.
One of the best ways to keep your mower running efficiently and to reduce fire risk is to
regularly remove debris buildup from the mower. Follow the recommendations below
and contact your authorized dealer with any questions.
• Allow the machine to cool in an open area before cleaning.
• Do not use water on any part of the mower except the underside of the cutting deck.
Doing so can cause damage to the mower's spindle bearings, electrical system and
engine, leading to premature failures. The use of compressed air and/or leaf blower
will help keep the mower clean.
• Clean around the exhaust manifold, fuses, all wiring and harnesses, muffler pipe,
muffler shield, engine intake screens and cooling fins, etc. See Figure 16.
• Clean the top of the mower deck, under the spindle covers and belt area. See
Figure 17.
• Clean around and near the transmission, axle and the fan area. See Figure 18.
nOTE: Wheel not
shown for clarity.
Figure 16
Figure 17
Figure 18
English
15