Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Carbine 55CSR
Summary of Contents for Carbine 55CSR
- Page 1 O W N E R ’ S M A N U A L REMOTE START with SECURITY & KEYLESS ENTRY SYSTEM...
-
Page 2: Congratulations
Congratulations Congratulations on the purchase of this CARBINE keyless entry and remote start system. Reading this owners guide prior to using the system will familiarize you with it’s many features. If issues arise or you have questions, contact your installing dealer first. Additionally, you can contact us... -
Page 3: Replacement Remote Controls
Replacement Remote Controls To purchase replacement remote controls, please see your authorized dealer/installer or visit us at www.CARBINE.com Remote part numbers are found on the back of the remote control. -
Page 4: Table Of Contents
Contents Congratulations ..................2 Replacement Remote Controls ..............3 Remote Configuration ................5 LCD Configurations ..................6 Arming/ Disarming ..................8 Disarm without a Transmitter ..............8 Passive Arming/Locking ................9 Panic Alarm ....................9 Trunk Release (CH#3) ................9 Car Finder ....................10 Valet Mode....................10 Trigger the System ...................11 Progressive Door Trigger ................11 Tamper Warnings ..................12 Forced Passive Arming ................12... -
Page 5: Remote Configuration
Remote Configuration Button Feature Comment Lock/ Arm Press and release. Unlock/ Disarm Press and release. Panic Alarm On Press and hold for 1.5 sec. Arm and delete the Press two times within – on-board shock sensor 5 seconds. 2 short chirps + 1 long Arm and delete all trigger Press three times within... -
Page 6: Lcd Configurations
Remote Configuration (continued) Timer Start Press together and release. Ignition must be on. Press and Arm While Driving hold for 1.0 sec. Engine Running. Press both Turbo Timer Activation then release. Car Finder Press together and release. Standard LCD Icon Configurations LCD Icon Description LCD Icon... - Page 7 LCD Icon Description LCD Icon Description The remote battery needs to The remote battery is full be replaced The door is open or the alarm The hood is open or the alarm has been triggered from an has been triggered from an open door open hood The trunk is open or the...
-
Page 8: Arming/ Disarming
Note: If the system had previously been triggered, the tamper warning chirps will always sound upon disarm. Disarm without the Remote Control Your CARBINE system has an override mode that allows you to disarm your system in the event that you have lost or damaged your remote controller. -
Page 9: Passive Arming/Locking
Passive Arming/Locking Your CARBINE system can be programmed to Passive Arm and Lock the doors. If this feature is programmed on, it will automat- ically arm and lock the doors 30 seconds after the last protected entrance is closed. During the 30 second countdown, the RCC LED will flash fast and the siren/horn will chirp after 20 seconds to warn that the system is about to arm and lock. -
Page 10: Car Finder
Car Finder The Car Finder feature will help you locate your vehicle by flashing the parking lights. To Activate the Car Finder feature 1. Press and release the buttons at the same time. 2. The vehicle parking lights will flash (5) times. 3. -
Page 11: Trigger The System
Progressive Door Trigger This feature is ON by default and can be programmed off by the installer. When your CARBINE system is armed and a door is opened, instead of “full alarm mode” the system will chirp the horn/siren 10 times prior to going into full alarm mode. -
Page 12: Tamper Warnings
Tamper Warning at Disarm If the alarm had been triggered while you were away from the vehicle, upon disarming, a 4-chirp tamper disarm warning will occur. In addition to the 4-chirp warning, the status LED will flash a distinctive number of times to indicate which alarm zone set off the alarm. -
Page 13: Nuisance Prevention System
Nuisance Prevention System To prevent continuous alarm cycles from faulty and over-sensitive sensors or an attempted theft that has left a protected door open, the Nuisance Prevention System will monitor all trigger inputs. If the alarm triggers (3) times with a 60-minute period from the same sensor, the NPS will interpret this as a false trigger. -
Page 14: Key Takeover
Key Takeover: When you are ready to drive the vehicle 1. Unlock the door using the CARBINE remote control. 2. Enter the vehicle and do not step on the foot brake. 3. Insert the ignition key and turn it to the RUN position. -
Page 15: Quick Stop Mode
Quick Stop Mode: Your CARBINE remote starter can also keep the engine running during short trips away from the vehicle. To Enable Quick Stop Mode 1. Park in a well-ventilated area. 2. With the engine running, set the transmission in park and set the parking brake. -
Page 16: Timer Mode Starting
Timer Mode Starting Timed Mode allows you to keep the engine warmed by starting the engine every (3) hours. After (6) starts, this system will be off. To initiate Timer Mode Starting, press the buttons at the same time then release them. - The parking lights will flash (4) times. -
Page 17: Short Run Turbo Mode
Short-Run Turbo Timer Mode: Short Run Turbo Mode keep the engine running for a short length of time to allow the engines turbo boost system to cool down before stopping the engine. Activate the Turbo Timer Mode - Stop the vehicle and set the parking brake. - Press and release the at the same time. -
Page 18: Programming The Lcd Remote Controller
LCD Remote Controller Settings and Programming Enter Settings: To get into transmitter feature programming mode, press and hold the “F” button for 3 seconds. You will hear 2 beeps and the clock display will flash. Follow the instructions enclosed for each setting you want to program or change. - Page 19 Function Setting Daily Clock Display 1. Press the button to adjust hours. 2. Press the button to adjust minutes. 3. To exit the clock setting mode, push and hold the “F” button for 3 seconds or simply do nothing for 15 seconds. Note: Adjusting hours will change AM-PM.
- Page 20 Function Setting 1. Press and release the “F” key five times. Backlight Brightness Setting “50p” will be displayed. 2. Press the button to adjust the light level. You have “0p”, “50p” and “100p” to choose from. Note: Raising the display brightness to 100p will consume more battery power.
-
Page 21: Pairing A Replacement Remote Control
The horn/siren chirps 1 long chirp. The new remote is programmed. 8. Turn the ignition key to the Off position. A long chirp from the horn confirms that the pairing mode is off. Note: Your CARBINE security system will accept codes from up to (4) transmitters. -
Page 22: System Maintenance / Battery Replacement
System Maintenance Replacing the LCD 2-Way Remote Controller Battery The CARBINE LCD 2- way remote controllers are powered by a CR2450 Lithium battery. When the battery begins to weaken, the battery life indicator on the LCD screen will display the condition of the battery. - Page 23 Replacing the 4 Button Remote Controller Battery The CARBINE remote controllers are powered by a CR2032 Lithium battery. When the battery begins to weaken, the operating range of the remote control is reduced and the LED indicator on the remote will begin to dim.
- Page 24 © Copyright 2021 Magnadyne Corporation. All Rights Reserved. No part of this publication may be produced without the expressed written permission of Magnadyne Corporation. Carbine is a registered trademark of Magnadyne Corporation. For Warranty Information, please visit our website at www.carbine.com www.carbine.com | call 310-735-2000 | UM-55CSR...
Need help?
Do you have a question about the 55CSR and is the answer not in the manual?
Questions and answers