1. Manuals
  2. Brands
  3. ICP DAS USA Manuals
  4. IP Camera
  5. iCAM-MR6422X
  6. Quick start manual

ICP DAS USA iCAM-MR6422X Quick Start Manual

Hide thumbs Also See for iCAM-MR6422X:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
Packing List
IP Camera iCAM-MR6422X
iCAM-MR6422X x 1
Screws and Anchor Set
Technical Resources
How to search for drivers, manuals and spec information on ICP DAS website.
 For Mobile Web
 For Desktop Web
iCAM- MR6422X Quick Start
includes following items:
(inserted in)
4 GB Micro SD Card x 1
x 3,
Hex Key (Allen Key) x 1
v1.1, 05/2020
Alignment Sticker X 1
Technical Support
service@icpdas.com
www.icpdas.com
Quick Start x 1
P.1

Advertisement

Table of Contents
loading

Related Manuals for ICP DAS USA iCAM-MR6422X

Summary of Contents for ICP DAS USA iCAM-MR6422X

  • Page 1 MR6422X Quick Start v1.1, 05/2020 Packing List includes following items: IP Camera iCAM-MR6422X (inserted in) Alignment Sticker X 1 iCAM-MR6422X x 1 4 GB Micro SD Card x 1 x 3, Quick Start x 1 Screws and Anchor Set...
  • Page 2 Part Description & Dimensions 單位: mm  Bottom bracket  Upper cover  Transparent cover  Lens  RJ-45 Ethernet connector (support PoE)  Power jack (DC12V ±10%)  Micro SD card slot  Factory default button...

  • Page 3: Hardware Installation

    Hardware Installation 1) Retrieve the camera and remove the bottom bracket from the upper cover with a hex key (PIC.1). Use the included screws through the holes marked as “a”, and fix the camera in the desired location (PIC.2&3). 2) Attach the Ethernet and power cables to the RJ-45 connector and the DC-in connector, respectively...
  • Page 4  Connect the RJ-45 Ethernet cable with a waterproof connector o First, remove the waterproof connector and unscrew the waterproof nut. Insert the Ethernet cable and connect to the RJ-45 connector with proper tools (PIC.5). Then, tighten the waterproof connector and nut before the RJ-45 connector is connected to the camera (PIC.6).

  • Page 5: System Architecture

    System Architecture For connecting IP Camera to your network, please choose one of the following system architectures: (1). Use DC12V power adaptor and network switch connected to a network. (2). Connected to the network using a PoE switch. (3). Use PoE power injector and network switch connected to the network.

  • Page 6: Reset To Factory Defaults

    Reset to Factory Defaults Reset the hardware to factory defaults, please follow these steps: 1. Press and hold “RESET Key” for 10 seconds and release. 2. Wait for 40 seconds, then the network LED light will turn off, and go back on again. 3.
  • Page 7 Configuring IP Addresses via Web Interface Set your PC Address the same network segment as the default IP address (192.168.0.200). Key in the default iCAM IP address in the web browser and follow the steps below: 1. Login to the iCAM by key in the default username “admin” and password “pass”.
  • Page 8 Internet Properties & Security Settings Make sure your Internet browser allows the ActiveX plug-in to work on your computer. Set Download Signed ActiveX controls to “Prompt”and Run ActiveX controls and plug-ins to “Enable”. You can set this option through Control Panel→ Network and Internet→Manage Browser Add-ons→Internet Properties→Security→Costom Level.

Table of Contents