Advertisement
Features of your Aquella
Care and Cleaning
1
Always disconnect the kettle from the
CAUTION: Do not use chemicals, steelwool,
power outlet before cleaning.
or abrasive cleaners to clean the outside
of the kettle, as these will scratch the
Never immerse the kettle switch area, cord
stainless steel surface.
or power base in water, or allow moisture to
2
come into contact with these parts.
To clean the mesh filter
Removal of mineral deposits.
Press the button on the handle to open the
hinged lid. Grasp the top of the mesh filter
Mineral deposits in tap water may cause
and pull upwards to remove. Wash in warm
3
the interior of the water gauge to discolour.
soapy water and dry thoroughly before
To remove this build-up, use Sunbeam
replacing in the kettle.
Liquid Descaler, a simple to use, non-toxic
cleaner available from Sunbeam Appointed
Cleaning the concealed heating element
Service Agents.
This kettle features a non-corrosive
stainless steel heating element. Over
Alternatively:
4
time, scale may build up on the
1.Fill the kettle with 3 cups of white vinegar
concealed element inside the kettle,
and the remainder with water and allow to
causing discolouration that may have the
stand overnight. DO NOT BOIL.
appearance of rust. Be assured this is
2.Empty the solution from the kettle. Any
not rust. If this occurs clean with a green
stains remaining inside the spout can be
Scotchbrite
®
scourer or similar and a
removed by rubbing with a damp cloth. Fill
suitable abrasive cleaning cream. Rinse
the kettle with clean water, bring to boil
and clean thoroughly with tap water before
and then discard the water. Repeat and the
using your kettle again.
kettle will then be ready to use.
To clean the stainless exterior
The stainless steel surface may be wiped
over with a damp cloth and polished with a
soft dry cloth.
3-Way Safety System.
6
1 – Automatically switches the kettle off after boiling.
2 – Cuts out for boil-dry production.
3 – Shuts down in case of overheating.
1. Easy read water gauge
The full length water gauge indicates
the volume of water in the kettle up
to 1.8 litres.
2. Stylish stainless steel design
Long life stainless steel to suit any
kitchen décor.
3. 2200 watt concealed element
The fast boil 2200 watt element is
concealed in the base of the kettle
for longer element life. The smooth
stainless floor reduces scale build
up and allows for easy cleaning.
4. Removable mesh filter
Keeps the water clean of any foreign
matter and is removable for easy
cleaning.
2
Kettle
®
Notes
5
6
7
8
5. Hinged lid with safety lock
Hinged locking lid opens at the push
of a button for one-handed use and
for safety, locks shut to reduce the
chance of accidental scolding.
6. 360 degree cordless power base
Designed to allow you to place the
kettle on the base in any direction.
Convenient for both left and right
handed users.
7. Neon ON/OFF switch with auto cut-out
Lights up to indicate that the kettle
is on and heating. Switches the
kettle off automatically after boiling.
8. Cord storage facility
Excess cord can be wound around
the cord storage facility underneath
the power base.
Using your Aquella
Before using your kettle.
It is recommended that you clean your kettle
before use by filling the kettle with water, up
to the maximum level indicator, boil and
discard.
Using your kettle.
1. To fill the kettle, remove it from the power
base and lift the lid, by pressing the button
on the handle. Alternatively, the kettle may
be filled through the pouring spout.
2. Fill the kettle with the desired amount of
water. Always fill the kettle between the
minimum and maximum marks. Too little
water will result in the kettle switching off
before the water has boiled.
NOTE: Do not fill the kettle over the maximum
level, as water may spill out of the spout
when boiling.
3. Push the lid closed firmly until it locks into
position.
4. Place the kettle on the power base and
connect the plug into a 230/240 Volt AC
power outlet. Turn the power ON.
5. Press the ON/OFF button downwards at the
top of the handgrip. The power indicator
light will illuminate to indicate the kettle
is heating. The kettle will switch off
automatically once the water has boiled.
NOTE: Ensure that the ON/OFF switch is clear
of obstructions and the lid is firmly closed.
The kettle will not turn off if the ON/OFF
Sunbeam's 3-Way Safety System
Safety is a major consideration in the
design of a Sunbeam kettle. This is why we
have developed our 3-Way Safety System,
which ensures that your kettle will:
1. Automatically switch off after boiling.
For convenience, safety and energy
efficiency, your Sunbeam kettle will
automatically switch off after boiling.
2. Cut-out for boil-dry protection.
If the kettle is operated without water, it
will automatically cut-out, preventing any
Kettle
®
switch is constrained or if the lid is left
open. Do not remove the kettle from the
power base while in use.
6.Lift the kettle from the power base and
pour the water.
NOTE: Use caution when pouring the water
from your kettle, as boiling water will scald.
7. The kettle may be stored on the power
base while not in use. The kettle will not
re-boil until the ON/OFF switch is pressed
downward.
NOTE: Ensure the power is turned off at the
power outlet when the kettle is not in use.
Should you accidentally allow the kettle to
operate without water, boil-dry protection will
automatically switch it off. If this occurs,
allow the kettle to cool before filling with
cold water and re-boiling.
Cord Storage Facility.
Excess cord can be stored by winding the
cord around the storage facility underneath
the power base.
360° power base
damage to the element.
If this occurs, allow the kettle
to cool before filling with cold
water and re-boiling.
3. Shut-down in case of overheating.
In the event of overheating, the kettle will
automatically shut down to prevent further
damage. Should this occur, take your kettle
to a Sunbeam Service Centre or Appointed
Service Agent.
3
Advertisement
