Maintenance - Craftsman CMCST910 Instruction Manual

6. Wind the cutting line onto the spool in the direction of
the arrow on the spool. Make sure to wind the line on
neatly and in layers. Do not crisscross.
7. When the wound cutting line reaches the recesses
cut the line.
8. Fit the spool onto the appliance as described in
Replacing Spool Assembly.

MAINTENANCE


WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories,
when replacing line, or prior to cleaning. An
accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning

WARNING:
of all air vents with clean, dry air at least once a
week. To minimize the risk of eye injury, always
wear ANSI Z87.1 approved eye protection when
performing this procedure.

WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
a liquid.
Accessories

WARNING:
those offered by CRAFTSMAN, have not been tested
with this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact CRAFTSMAN call 1‑888‑331‑4569 .
Replacing Guard (Fig. E, F)

WARNING:
without guard firmly in place. Damage or personal
injury could result.
30
To reduce the risk of serious
Blow dirt and dust out
Never use solvents or other
Since accessories, other than
Never operate appliance
Remove Current Guard
1. Remove the guard screw
2. Slide the guard
,
Assembling the New Guard
1. Slide the guard into place as shown in Fig. F.
2. Replace and securely tighten the guard screw
Versatrack™ (Fig. O)

WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.

WARNING:
personal injury, do not use a damaged Versatrack™
hang hook or Versatrack™ Trackwall. A damaged
Versatrack™ hang hook or Versatrack™ Trackwall will
not support the weight of the tool.

WARNING:
personal injury, DO NOT suspend tool overhead or
suspend objects from the hang hook. ONLY suspend
tool on the Versatrack™ Trackwall using the hang hook.

WARNING:
does not exceed the maximum rated weight of 20 lb
(9 kg) for the selected Versatrack™ hook.

WARNING:
Versatrack™ Trackwall rail, adequately space the tools
in order to not exceed 75 lb (35 kg) per linear foot.
iMPORTAnT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwall system.
1. Turn the tool off, remove the battery pack
and accessories.

CAUTION:
cutting teeth must have them covered securely if it is to
be on the Versatrack™ Trackwall.
2. Flip or pull open the integral hang hook
when locked into position.
3. Mount the integral hang hook to the
Versatrack™ Trackwall.
nOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1‑888‑331‑4569.
19 shown in Fig. E.
9 off.
To reduce the risk of serious
To reduce the risk of serious
To reduce the risk of serious
Ensure that the tool weight
When hanging objects on a
Any product with exposed
31
English
19 .
. It clicks
13