IMPORTANT WARNING CAUTION: DVD PLAYER IS A CLASS 1 LASER PRODUCT. HOWEVER THIS PLAYER USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED. THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE PLAYER. CLASS 1 LASER PRODUCT (Printed on the Rear Panel)
WHEN REPLACING DVD DECK [ When the removal of the DVD Deck ] Before removing Pick Up PCB and DVD PCB connector, make the short circuit on the position as shown Fig. 1 using a soldering. If you remove the DVD Deck with no soldering, the Laser may be damaged.
PARENTAL CONTROL - RATING LEVEL 4 DIGIT PASSWORD CANCELLATION If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the steps below. Turn Unit ON. Set the DVD to the Stop Mode. Check that the 'No disk' is displayed on the screen. Press and hold the 'STOP' button on the front panel.
ABOUT LEAD FREE SOLDER (PbF) Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF printing on the PCB. (Please refer to figures.) Caution: • Pb free solder has a higher melting point than standard solder; Typically the melting point is 50°F~70°F(30°C~40°C) higher.
TABLE OF CONTENTS IMPORTANT WARNING ..................... A1-1 SERVICING NOTICES ON CHECKING ..............A1-1 HOW TO ORDER PARTS ................... A1-1 WHEN REPLACING DVD DECK ................A1-2 DISC REMOVAL METHOD AT NO POWER SUPPLY ..........A1-2 PARENTAL CONTROL - RATING LEVEL ..............A1-3 TRAY LOCK ........................
GENERAL SPECIFICATIONS CRT Size / Visual Size 15 inch / 357.0mmV System CRT Type Flat Deflection degree Magnetic Field BV/BH +0.45G / +0.18G Color System Speaker 2 Speaker Position Front Size 1.5 x 2.7 Inch Impedance Sound Output 1.5W + 1.5W 10%(Typical) 1.5W + 1.5W DVD System...
Page 8
GENERAL SPECIFICATIONS Regulation Safety CE,BEAB Radiation X-Radiation NONE Temperature Operation +5oC ~ +40oC Storage -20oC ~ +60oC Operating Humidity Less than 80% RH On Screen Menu Display Menu Type Character CH Tuning Manual Auto CH Allocation Picture Contrast Brightness Color Tint (NTSC Only) Sharpness Audio...
Page 9
GENERAL SPECIFICATIONS G-10 On Screen Menu (DVD) Display Menu Type Character Language Menu Subtitle Audio Picture TV Screen Size OSD Display On/Off JPEG Interval Select Files Sound DRC (Dynamic Range Control) dts Decode Output(5.1ch/ 2ch) Surround On/Off Center On/Off Sub Woofer On/Off Parental Password Lock/ Un Lock Rating Level...
Page 10
GENERAL SPECIFICATIONS G-13 Remote Unit RC-HF Control Glow in Dark Remocon Unit Format Custom Code 71-8E Power Source Voltage(D.C) UM size x pcs UM-4×2 pcs Total Keys Keys Keys Power 0/AV Open/Close Play Stop Display/Call TV/DVD Cancel Audio Angle Subtitle Subtitle On/Off Title Setup/Menu...
Page 11
GENERAL SPECIFICATIONS G-14 Features Auto Shut Off Auto Search Auto Setup CH Allocation Auto CH Memory Protect of FBT Leak Circuit Power On Memory T'Text Text type Fastext Text Language English, French, Swedish, Hunganan, Finnish Turkish, German, Dutch, Portuguese, Spanish Italian, Greek Tray Lock Parental Lock (DVD Only)
Page 12
GENERAL SPECIFICATIONS G-16 Interface Switch Front Power(Tact) Channel Up Channel Down Volume Up Volume Down Play Stop Skip+/Search+ Skip-/Search- Open/Close Still/Pause Main Power SW Indicator Power Stand-by Yes (Red) On Timer Terminals Front Video Input RCA x 1 Audio Input RCA x 2 Other Terminal Headphone (Stereo &...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: AV PCB/DVD BLOCK (Refer to Fig. 1-3) Remove the 2 screws 1. AND P.C. BOARDS Disconnect the following connectors: 1-1: BACK CABINET (Refer to Fig. 1-1) (CP301, CP302, CP402, CP3801 and CP3802). Remove the 5 screws 1.
Page 14
DISASSEMBLY INSTRUCTIONS 1-5: DVD PCB/DVD DECK (Refer to Fig. 1-5) Make the short circuit on the position as shown Fig. 1-5 using a soldering. If you remove the DVD Deck with no soldering, the Laser may be damaged. Remove the 4 screws 1. Remove the DVD Deck in the direction of arrow (A).
DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DVD DECK PARTS NOTE In case of the Main Chassis Ass'y, install it from (1) to NOTE (4) in order. (Refer to Fig. 2-2-B) 1. Do not disassemble the DVD DECK PARTS except In case of the Main Chassis Ass'y installation, hook the listed parts here.
Page 16
DISASSEMBLY INSTRUCTIONS NOTE 2-5: CLAMPER ASS'Y (Refer to Fig. 2-5-A) In case of the Pulley Motor installation, check if the Press the Clamper and rotate the Clamper Plate clockwise, then unlock the 3 supports 1. value of the Fig. 2-3-B is correct. When installing the Loading Motor PCB Ass'y, install it Remove the Clamper Plate, Clamper Magnet and correctly as Fig.
Page 17
DISASSEMBLY INSTRUCTIONS Insulator (R) ~ FEED MOTOR ~ Main Chassis Ass'y (Top Side) BLUE (4) ORANGE (3) Switch PCB Ass'y Fig. 2-6-C ~ SPINDLE MOTOR ~ BLACK (2) 2-7: RACK FEED ASS'Y/SWITCH PCB ASS'Y/FEED RED (1) MOTOR (Refer to Fig. 2-7-A) •...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction 3. REMOVAL OF ANODE CAP to remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS REMOVAL AND INSTALLATION OF When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using FLAT PACKAGE IC a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 4-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 20
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 4-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than a standard time (second).
WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: No need setting for after INI 16 due to the adjustment value. Table 1 Enter DATA SET mode by setting VOLUME to minimum.
ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL FUNCTION FUNCTION CUT OFF TINT ADJUSTMENTS RF AGC SHARP AGC GAIN CONT CENT Read and perform these adjustments when repairing the R DRIVE CONT MAX R CUTOFF CONT MIN circuits or replacing electrical parts or PCB assemblies. G DRIVE COLOR CENT G CUTOFF...
Page 24
ELECTRICAL ADJUSTMENTS 2-4: FOCUS 2-7: VERTICAL SIZE NOTE: Adjust after performing adjustments in section 2-6. Receive a broadcast. Turn the Focus Volume fully counterclockwise once. Receive the monoscope pattern from the Pattern Adjust the Focus Volume until picture is distinct. Generator.
Page 25
ELECTRICAL ADJUSTMENTS 2-10: CUT OFF 2-13: CONTRAST CENT Set condition is AV MODE without signal. Activate the adjustment mode display of Fig. 1-1 and Using the remote control, set the brightness and press the channel button (22) on the remote control to contrast to normal position.
Page 26
ELECTRICAL ADJUSTMENTS 2-15: Confirmation of Fixed Value (Step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. FUNCTION STEP NO. AGC GAIN R CUTOFF G CUTOFF B DRIVE V POSI 50 V POSI 60 BRIGHT MAX BRIGHT MIN TINT...
Page 27
ELECTRICAL ADJUSTMENTS 3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator.
Page 29
DVD BLOCK DIAGRAM FLASH 8M 64M SDRAM IC4007 IC4005 SST39VF800A- HY57V641620 70-4C-EK-DSS HGT-7 HA0~HA20, HD0~HD15 TV BLOCK DVD LOADER CD4002 RFA_SDEN, DATA, SCLK A, B, C, D, E, F READ CHANNEL AAF_CE, FE, TE, PI Pick up IC2601 ZR36708TQC FNN, FNP UNREG+3.8V CD, DVD, LD VBIASS0, S1...
Page 30
TV BLOCK DIAGRAM *A---P.CON+9V *B---P.CON+12V TU101 *C---P.CON+A5V SCL SDA AGC IF *D---CHROMA+5V SAW FILTER *E---AT+5.7V CF606 *F---AT–8V FROM DVD BLOCK *A *C IC4201 CHROMA NJM4580M(TE1) IC601 STV2246H Q804 VIDEO SW DVD_A OUT_L MEMORY IC602 MM1502XNRE IC199 S-24C08ADPA-01 BLUE AMP DVD_A OUT_R Q805 GREEN AMP V801...
Page 31
POWER BLOCK DIAGRAM DEGAUSS SOUND+B Q3003 DVD 3.3V P.CON+3.3V Q3801 RY3801 Q3004 DEGAUSS RELAY SW RELAY CURRENT CTL. VOLT CURRENT CONTROL IC3002 LA6324NML-TE-L TRANSFORMER Q3014 SWITCHING F3801 D3802~D3805 T3801 PROTECTOR RECTIFIER IC3804 IC3801 PS2561AL1-1-V(W) Q3805 STR-W6853 Q3009 FEED BACK FEED BACK POWER REG.
Page 35
PRINTED CIRCUIT BOARDS LOADING MOTOR (INSERTED PARTS) LOADING MOTOR (CHIP MOUNTED PARTS) SOLDER SIDE SOLDER SIDE CD2302 SOLDER SIDE CD2301 M2601 M2602...
SOUND AMP SCHEMATIC DIAGRAM (AV PCB) SOUND AMP IC SOUND AMP IC IC301 AN7523N IC302 AN7523N L CH CP301 SP301 SPEAKER TID-X02P-M1 SG04D11BNA SP OUT L+ 8 OHM SP OUT L- CD301 CU123801 R CH CP302 SPEAKER TID-X02P-M1 SP OUT R+ 8 OHM FROM POWER SP OUT R-...
WAVEFORMS AUDIO/VIDEO CHROMA/SIF/VIF/21PIN MPEG/MICON/DSP 500µs 10ns 100mV 100mV DEFLECTION 500µs 200ns 100mV 20mV MEMORY 10µs 200mV 20mV RF AMP/DSP 10µs 200ns 200mV 20mV 10µs 200ns 100mV 10mV NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 52
WAVEFORMS MICON/TUNER CHROMA/SIF/VIF/21PIN NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 53
WAVEFORMS CHROMA/SIF/VIF/21PIN SOUND AMP AUDIO SW IN/OUT MICON/TUNER NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
DVD DECK EXPLODED VIEW Cannot supply by a unit. M2603 PCB610 (LOADING MOTOR PCB ASS'Y) CD2302 CD2301 PCB640 CD2001 (SW PCB ASS'Y) Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more. If the repair is needed, replace the DVD MECHA ASS'Y.