Fortinet FortiMail-5001A Quick Start Manual

For more information
• Documentation CD: all major FortiMail documents
• Fortinet Technical Documentation:
• Fortinet Knowledge Base:
• Fortinet Technical Support:
• Fortinet Training Service:
Package Contents
AMC slot with ASM-S08
(80GB storage)
5001A
HS
OOS
ACT/RDY
PORT
ASM-S08
Retention
Screw
Extraction
Lever
Straight-through
Console Cable
Ethernet cables
HS
OOS
ACT/RDY
PORT
ASM-S08
Grounded wrist band
ASM-S08 storage module
LED descriptions
LED State
1, 2 Green
(Left LED)
Flashing Green
Off
1, 2 Green
(Right LED)
Amber
Off
Base CH0/CH1 Green
Flashing Green
Fabric CH0/CH1 Off
Flashing Green
ACC Off or Flashing green Flashes green when the FortiMail-5001A board accesses the FortiOS flash disk. The FortiOS flash disk stores the
OOS Off
(Out of
Green
Service)
Power Green
Status Off
Flashing Green
IPM Blue
Flashing Blue
Off
http://docs.fortinet.com
http://kb.fortinet.com
http://support.fortinet.com
http://campus.training.fortinet.com
RJ-45 Fabric and Base
Console network activity
LEDs
USB
IPM ACC
Port1 and Port2
LED OOS
10/100/1000 (board Power
Copper Interfaces position) Status
LEDs
FortiMail-5001A
Hardware Guide
T
5001A HS
OOS
PORT ACT/RDY
ASM-S08
ools and Documenation
Copyright 2009 Fortinet Incorporated. All rights reserved.
Trademarks
Products mentioned in this document are trademarks.
Welcome | Bienvenue | Willkommen |
Description
Port has power and network connection.
Network activity at the interface.
No link is established.
Connection at 1 Gbps.
Connection at 100 Mbps.
Connection at 10 Mbps.
Base backplane interface 0 (base1)/interface 1 (base2) is connected at 1 Gbps.
Network activity.
Fabric backplane interface 0 (fabric1)/interface 1(fabric2) is connected at 10 Gbps.
Network activity.
current FortiOS firmware build and configuration files. The system accesses the flash disk when starting up, during a
firmware upgrade, or when an administrator is using the CLI or GUI to change the FortiOS configuration. Under normal
operating conditions this LED flashes occasionally, but is mostly off.
Normal operation.
A fault condition exists and the FortiMail-5001A blade is out of service (OOS). This LED may also flash very briefly
during normal startup.
The FortiMail board is powered on.
The FortiMail board is powered on.
The FortiMail-5001A system is starting up. If this LED is flashing at any time other than system startup, a fault condition
may exist.
The FortiMail-5001A system is ready to be hot-swapped (removed from the chassis). If the IPM light is blue and no
other LEDs are lit the FortiMail-5001A board has lost
The FortiMail-5001A system is changing from hot swap to running mode or from running mode to hot swap. This
happens when the FortiMail-5001A system is starting up or shutting down.
Normal operation. The FortiMail-5001A board is in contact with the chassis backplane.
QuickStart Guide
5001A
© Copyright 2010 Fortinet Incorporated. All rights reserved.
Trademarks
Products mentioned in this document are trademarks or registered
trademarks of their respective holders.
Regulatory Compliance
FCC Class A Part 15, CE, and UL
Version 4.0
9 February 2010
http://www.fortinet.com
Connectors
Connector Type Speed
1, 2 RJ-45 10/100/1000
Retention
Screw
CONSOLE RJ-45 9600 bps
Extraction
Lever
USB USB
Factory default settings
Default mode
Administrator
account on Port 1
Management Access HTTPS, Ping, SSH
| | Bienvenido | Benvenuto
power.
HS
OOS
ACT/RDY
PORT
ASM-S08
Protocol Description
Ethernet Copper 1-gigabit connection to
Base-T 10/100/1000Base-T copper
networks.
RS-232 Serial connection to the
8/N/1 serial command line interface.
Backing up or restoring mail data
in Server mode. For details, see
the FortiMail Administration
Guide on the documentation CD.
Gateway mode
User name/ admin/(No password)
Password:
Web-based https://192.168.1.99/admin
manager URL:
FortiMail-5001A