Related Manuals for Microm TX3 Series
Summary of Contents for Microm TX3 Series
- Page 1 All manuals and user guides at all-guides.com TX3 Series Touch Screen Installation Manual TX3 Touch Screen Installation Manual Version 3.4 1 (93) LT-996 Copyright 2015...
- Page 2 All manuals and user guides at all-guides.com TX3 Touch Screen Installation Manual 2 (93) Version 3.4 Copyright 2015 LT-996...
-
Page 3: Table Of Contents
All manuals and user guides at all-guides.com Contents Introduction TX3 Systems Features Touch Screen Sizes and Enclosures Touch Screen Accessories Warranty and Special Notices About This Manual Contact Us Enclosure Installation Installing the Enclosures and Touch Screen Installing the 15” Kiosk Installing the 15”... - Page 4 All manuals and user guides at all-guides.com TX3 Touch Screen Installation Manual 4 (93) Version 3.4 Copyright 2015 LT-996...
- Page 5 All manuals and user guides at all-guides.com List of Figures Figure 1 TX3 devices on an RS-485 network. Figure 2 TX3 devices connected to an ethernet TCP/IP network. Devices connected to an ethernet network are Master Nodes. Figure 3 TX3 devices connected to a combination ethernet TCP/IP network with RS-485 subnetworks.
- Page 6 All manuals and user guides at all-guides.com Figure 32 Attach the 22” Touch Screen to the stand Figure 33 Attach the 22” Touch Screen to the stand Figure 34 Inside the Switching Power Supply Box Figure 35 Power Supply Voltage Selection Switch Figure 36 Touch Screen Power Supply Enclosure Figure 37...
-
Page 7: Introduction
All manuals and user guides at all-guides.com Introduction Introduction This manual provides information about the installation and operation of the Touch Screen, and must be read in its entirety before beginning any installation work. Installation must be performed by a qualified technician and must adhere to the standards and special notices set by the local regulatory bodies. -
Page 8: Tx3 Systems
All manuals and user guides at all-guides.com Introduction TX3 Systems The Mircom's TX3 series of Touch Screens provide high quality two-way communication between residents and their visitors in a multi-unit dwelling establishment. The basic TX3 system consists of the TX3 Touch Screen and depending on the application, may be integrated with a combination of Mircom Telephone Access, Card Access, and Elevator Restriction Units. -
Page 9: Figure 1 Tx3 Devices On An Rs-485 Network
All manuals and user guides at all-guides.com Introduction The TX3 Configurator software can connect to any of these network configurations. How you connect to the network (that is, through TCP/IP, USB, a modem, or the COM port) determines what devices you can configure on the system. -
Page 10: Figure 2 Tx3 Devices Connected To An Ethernet Tcp/Ip Network. Devices Connected To An Ethernet Network Are Master Nodes
All manuals and user guides at all-guides.com Introduction ethernet TCP/IP network. If you connect directly to one of the Master Nodes using USB, a modem, or a COM port, you will be able to configure that device but not any other device. Touch Screen Unit Elevator Restriction Unit (Master Node) -
Page 11: Figure 3 Tx3 Devices Connected To A Combination Ethernet Tcp/Ip Network With Rs-485
All manuals and user guides at all-guides.com Introduction Figure 3 shows a configuration with TX3 devices connected on both an ethernet TCP/IP network and on RS-485 subnetworks. Devices connected to a Master Node’s RS-485 subnetwork are Slave Nodes to the Master Node. Each RS-485 subnetwork can have up to 63 devices connected to it;... -
Page 12: Features
Touch Screen options such as color and themes), the Touch Screen panel must be set as an Master Node even if there is no slave panel connected to it. Features Features of the TX3 series include: • Stainless steel front panel •... -
Page 13: Touch Screen Accessories
All manuals and user guides at all-guides.com Introduction 1.3.1 15 Inch Models The 15 inch Touch Screen models are stand alone, surface or flush mounted. TX3-TOUCH-K15-A. 15” Touch Screen kiosk, stainless steel finish Touch Screen with speaker, microswitch for postal lock and a PS-4P transformer plug. Designed for indoor use. -
Page 14: Warranty And Special Notices
About This Manual This manual provides comprehensive information on the installation and configuration of the TX3 Series Touch Screen by the installation technician. Tasks are described in the order that they are likely to be performed. This manual applies to the following models: •... -
Page 15: Contact Us
LT-1160 • TX3 Two Door Card Access System Kit Catalogue Number 6531 • TX3 Series Elevator Restriction Accessories Catalogue Number 6532 Contact Us Mircom fosters a collaborative support process and environment in providing early feedback to meet your specific needs. - Page 16 All manuals and user guides at all-guides.com Introduction 1.7.3 Website Visit the Mircom website, at www.mircom.com, to find the product information you are looking for and to learn about troubleshooting, training and technical support options. The website provides avenues for customers to ask questions about new and existing technologies, and receive expert technical support about software and products.
-
Page 17: Enclosure Installation
All manuals and user guides at all-guides.com Enclosure Installation Enclosure Installation This chapter provides information on how to install the various enclosures and pre-assembled components. This chapter explains • Installing the 15” Kiosk - page 19 • Installing the 15” Touch Screen Surface Mount Enclosure - page 25 •... -
Page 18: Installing The Enclosures And Touch Screen
All manuals and user guides at all-guides.com Enclosure Installation Installing the Enclosures and Touch Screen The Touch Screen Kiosk, Surface Mount and Flush Mounts units consist of the following pre-assembled components: Kiosk. The kiosk is a pedestal mounted Touch Screen TX3-TOUCH-K15-A unit and consists of the following components: •... -
Page 19: Installing The 15" Kiosk
All manuals and user guides at all-guides.com Enclosure Installation Installing the 15” Kiosk 17.950 14.187 Figure 4. Kiosk Dimensions (inches) The Kiosk mounts to the floor inside the building near the entrance, close to the power source and telephone infrastructure. Access for the power and communication cables is provided through a cutout in the base plate. -
Page 20: Figure 5 Reinforcement Bracket With Bolts
All manuals and user guides at all-guides.com Enclosure Installation To install the Touch Screen Kiosk base plate Find a suitable location for the Kiosk next to the building entrance and above the building electrical and communications conduit. Remove the door from the Kiosk. Remove the 4 bolts from the reinforcement bracket, as shown in Figure 5. -
Page 21: Figure 6 Reinforcement Bracket With Nuts
All manuals and user guides at all-guides.com Enclosure Installation Figure 6. Reinforcement Bracket with nuts Remove the remaining 8 bolts that attach the Kiosk to the base plate, as shown in Figure 7. Figure 7. Kiosk Base Plate with bolts The 12 Kiosk mounting holes in the base plate are shown in Figure 8. -
Page 22: Figure 9 Base Plate Mounting Holes
All manuals and user guides at all-guides.com Enclosure Installation Using the Kiosk base plate as a template, trace an opening in the floor for the cutout and mark the 4 base plate mounting hole locations as shown in Figure 9. Ensure that the base plate is aligned with the electrical conduit. Figure 9. -
Page 23: Figure 11 Fitting The Kiosk On The Base Plate
All manuals and user guides at all-guides.com Enclosure Installation To fit the Touch Screen Kiosk on the base plate Fit the back lip of the Kiosk into the notches in the baseplate, and tilt the Kiosk forwards so that it rests on top of the base plate. Figure 11. -
Page 24: Figure 13 Attach The Kiosk To The Base Plate
All manuals and user guides at all-guides.com Enclosure Installation Secure the Kiosk onto the base plate using the 8 of the 12 base plate bolts in the holes shown in Figure 13. Attach the Kiosk to the base plate with bolts in these holes first Figure 13. -
Page 25: Installing The 15" Touch Screen Surface Mount Enclosure
All manuals and user guides at all-guides.com Enclosure Installation Installing the 15” Touch Screen Surface Mount Enclosure 18.920 18.920 12.600 12.600 3.500 3.500 Figure 14. 15” Touch Screen Surface Mount Back Dimensions (inches) TX3 Touch Screen Installation Manual Version 3.4 25 (93) LT-996 Copyright 2015... -
Page 26: Figure 15 15" Touch Screen Surface Mount Front Dimensions (Inches)
All manuals and user guides at all-guides.com Enclosure Installation 3.622 3.622 19.000 19.000 0.120 0.120 Figure 15. 15” Touch Screen Surface Mount Front Dimensions (inches) The surface mount enclosure mounts on the wall. Mount the enclosure right-side up (the Mircom logo on the door is on the bottom). You need: •... -
Page 27: Figure 16 Touch Screen Surface Mount
All manuals and user guides at all-guides.com Enclosure Installation Figure 16. Touch Screen Surface Mount To install the surface mount enclosure Find a suitable location for the enclosure. Using the enclosure as a template, mark the back mounting locations of the two keyholes as shown in Figure 16. -
Page 28: Installing The 15" Touch Screen Flush Mount Enclosure
All manuals and user guides at all-guides.com Enclosure Installation Installing the 15” Touch Screen Flush Mount Enclosure 3.500 3.500 18.000 18.000 12.600 12.600 1.400 1.400 Figure 17. 15” Touch Screen Flush Mount Back Dimensions (inches) TX3 Touch Screen Installation Manual 28 (93) Version 3.4 Copyright 2015... -
Page 29: Figure 18 15" Touch Screen Flush Mount Front Dimensions (Inches)
All manuals and user guides at all-guides.com Enclosure Installation 3.622 3.622 19.000 19.000 0.120 0.120 1.400 1.400 Figure 18. 15” Touch Screen Flush Mount Front Dimensions (inches) The flush mount enclosure mounts directly inside the wall to the wall stud or supporting structure as shown in Figure 19. -
Page 30: Figure 19 Flush Mount Enclosure
All manuals and user guides at all-guides.com Enclosure Installation Wall Enclosure Frame Enclosure Front GROUND SCREW LOCATION Side View Figure 19. Flush Mount Enclosure To install the flush mount enclosure Find a suitable location for the enclosure. You can mount the enclosure using the keyholes on the back, or the knockouts on the side, or both. - Page 31 All manuals and user guides at all-guides.com Enclosure Installation If you are using the keyholes, remove the enclosure and place 2 fasteners halfway into the wall into the marked keyhole locations. Then place the enclosure onto the top fasteners and lower it so that the fasteners fit in the narrow part of the keyholes.
-
Page 32: Installing The 22" Touch Screens
All manuals and user guides at all-guides.com Enclosure Installation Installing the 22” Touch Screens Attention: The 22” Touch Screen enclosure is heavy. Never attempt to lift this product by yourself. At least two people should lift it together. 2.5.1 Installing the Surface Mount Enclosure The surface mount enclosure mounts on the wall. -
Page 33: Figure 20 Surface Mounting The Enclosure
All manuals and user guides at all-guides.com Enclosure Installation Using the surface mount enclosure as a template, mark the back mounting hole locations of the two keyholes as shown in Figure 20. Ensure that at least one side is over a wall stud. Keyhole Keyhole screw... -
Page 34: Figure 21 Flush Mounting The Enclosure
All manuals and user guides at all-guides.com Enclosure Installation You need: 6 fasteners appropriate for the wall that you are mounting the enclosure on. To flush mount the enclosure Find a suitable location for the flush mount enclosure beside a wall stud. Attention: To comply with ADA regulations, the bottom of the enclosure must be no more than 36 inches from the ground. - Page 35 All manuals and user guides at all-guides.com Enclosure Installation Remove the enclosure and place the fasteners halfway into the wall into the marked hole locations. Place the enclosure onto the top fasteners and lower it so that the fasteners fit in the narrow part of the keyholes. Screw the other four fasteners into the four remaining holes.
-
Page 36: Figure 22 22" Touch Screen Flush Mount Dimensions (Inches)
All manuals and user guides at all-guides.com Enclosure Installation Figure 22. 22” Touch Screen Flush Mount Dimensions (inches) TX3 Touch Screen Installation Manual 36 (93) Version 3.4 Copyright 2015 LT-996... -
Page 37: Figure 23 22" Touch Screen Surface Mount Dimensions (Inches)
All manuals and user guides at all-guides.com Enclosure Installation Figure 23 22” Touch Screen Surface Mount Dimensions (inches) TX3 Touch Screen Installation Manual Version 3.4 37 (93) LT-996 Copyright 2015... -
Page 38: Assembling The Tx3-T-Kiosk Stand
All manuals and user guides at all-guides.com Enclosure Installation Assembling the TX3-T-KIOSK Stand 18.00 18.20 15.19 21.23 Figure 24. 22” Touch Screen Dimensions (inches) TX3 Touch Screen Installation Manual 38 (93) Version 3.4 Copyright 2015 LT-996... -
Page 39: Figure 25 15" Touch Screen Dimensions (Inches)
All manuals and user guides at all-guides.com Enclosure Installation 19.00 19.00 18.20 18.20 15.19 15.19 19.42 19.42 Figure 25. 15” Touch Screen Dimensions (inches) The Kiosk mounts to the floor inside the building near the entrance, close to the building power source and telephone infrastructure. Access for the power and communication cables is provided through a cutout in the base plate. -
Page 40: Figure 26 Components Of Tx3-T-Kiosk
All manuals and user guides at all-guides.com Enclosure Installation You will need: • 4 bolts to attach the base plate to the floor. The bolts need to fit holes that are 0.406” in diameter. Nuts (x6) Stand Screw cover (x8) Screw (x8) Screw cover base (x8) Base plate... -
Page 41: Figure 27 Base Plate Mounting Holes
All manuals and user guides at all-guides.com Enclosure Installation Using the base plate as a template, trace an opening on the floor for the cutout and mark the 4 base plate mounting hole locations as shown in Figure 27. Figure 27. Base Plate Mounting Holes Figure 28 shows the dimensions of the base plate. -
Page 42: Figure 29 Fit The Stand On The Base Plate
All manuals and user guides at all-guides.com Enclosure Installation To fit the TX3-T-KIOSK stand on the base plate Fit the back lip of the stand into the notches in the baseplate, and tilt the stand forwards so that it rests on top of the base plate. Figure 29. -
Page 43: Figure 31 Attach The Stand To The Base Plate
All manuals and user guides at all-guides.com Enclosure Installation Secure the stand onto the base plate using the screw cover bases, screws, and screw covers as show in Figure 31. Screw cover (x8) Screw (x8) Screw cover base (x8) Base plate Figure 31. -
Page 44: Figure 32 Attach The 22" Touch Screen To The Stand
All manuals and user guides at all-guides.com Enclosure Installation Hole for wiring Nuts (x6) Power and ground Figure 32. Attach the 22” Touch Screen to the stand TX3 Touch Screen Installation Manual 44 (93) Version 3.4 Copyright 2015 LT-996... -
Page 45: Figure 33 Attach The 22" Touch Screen To The Stand
All manuals and user guides at all-guides.com Enclosure Installation Power and ground Hole for wiring Nuts (x6) Figure 33. Attach the 22” Touch Screen to the stand Proceed with the wiring installation described in Chapter 3. TX3 Touch Screen Installation Manual Version 3.4 45 (93) LT-996... -
Page 46: Installing The Power Supply Enclosure
All manuals and user guides at all-guides.com Enclosure Installation Installing the Power Supply Enclosure The Touch Screen external power supply is an MD-990 156 W, 24 V single output switching power supply encased inside a metal enclosure. A voltage selectable switch is located on the side of the power supply and is factory set to 120V but can be switched to 230V. -
Page 47: Figure 35 Power Supply Voltage Selection Switch
All manuals and user guides at all-guides.com Enclosure Installation Switch the voltage selection switch to the required voltage level. Place a flathead screwdriver in between one of the holes in the chassis to access the switch. By default it is set to 115 Volts. Figure 35. -
Page 48: Figure 36 Touch Screen Power Supply Enclosure
All manuals and user guides at all-guides.com Enclosure Installation Figure 36. Touch Screen Power Supply Enclosure Dimensions without lid: Height: 7.500”, Width: 9.500”, Depth: 2.300” Overall dimensions: Height: 7.720”, Width: 9.830”, Depth: 2.378” To surface mount the power supply enclosure Find a suitable location for the power supply enclosure, such as over a wall stud. - Page 49 All manuals and user guides at all-guides.com Enclosure Installation Tighten all four screws into place. Note: The enclosure can also be mounted directly onto the drywall using anchors. TX3 Touch Screen Installation Manual Version 3.4 49 (93) LT-996 Copyright 2015...
- Page 50 All manuals and user guides at all-guides.com Enclosure Installation TX3 Touch Screen Installation Manual 50 (93) Version 3.4 Copyright 2015 LT-996...
-
Page 51: Touch Screen System And Setup
All manuals and user guides at all-guides.com Touch Screen System and Setup Touch Screen System and Setup This chapter describes the basic Touch Screen system, main panel, controller board components and provides information about its operation and setup. This chapter explains •... -
Page 52: Touch Screen System
All manuals and user guides at all-guides.com Touch Screen System and Setup Touch Screen System The TX3 Touch Screen may be networked with a combination of Telephone Access and Card Access Units through a peer-to-peer RS-485 connection. Touch Screen is capable of providing ADC or NSL telephone access from a single panel or from a networked system. -
Page 53: Figure 37 Single Touch Screen
All manuals and user guides at all-guides.com Touch Screen System and Setup 3.1.1 Single Touch Screen Figure 37 shows the simplest configuration for an ADC or NSL telephone system. Telephone outlet Central office line Control Unit Line1 Line1 Touch Screen Touch Screen Figure 37. -
Page 54: Figure 38 Single Touch Screen With Adc And Nsl Lines
All manuals and user guides at all-guides.com Touch Screen System and Setup Figure 38 shows a configuration using one Touch Screen connected to one ADC line and four NSL lines. Telephone outlet Central office line Control Control Control Control Unit Unit Unit Unit... -
Page 55: Touch Screen Panels
All manuals and user guides at all-guides.com Touch Screen System and Setup Touch Screen Panels 3.2.1 15” Touch Screen Main Panel On the Kiosk, the Touch Screen Panel is situated behind the front cover. To access the panel, unlock the Touch Screen and pull open the front cover. The 15”... - Page 56 All manuals and user guides at all-guides.com Touch Screen System and Setup 3.2.2 22” Touch Screen Inside Doors The 22” Touch Screen inside doors contain the following components as shown in Figure 40: • Speakers • Camera • Postal Lock (optional) •...
-
Page 57: Figure 40 22" Touch Screen Inside Door
All manuals and user guides at all-guides.com Touch Screen System and Setup • Keyhole Speakers Camera Microphone Postal Lock P300 Card Reader Keyhole Figure 40. 22” Touch Screen Inside Door TX3 Touch Screen Installation Manual Version 3.4 57 (93) LT-996 Copyright 2015... -
Page 58: Controller Boards
All manuals and user guides at all-guides.com Touch Screen System and Setup Controller Boards 3.3.1 15” Touch Screen Controller Boards The following Touch Screen controller boards are situated on a panel behind the 15” Touch Screen Panel as shown in Figure 41: •... - Page 59 All manuals and user guides at all-guides.com Touch Screen System and Setup 3.3.2 22” Touch Screen Controller Boards The 22” Touch Screen Panel contains the following components and controller boards as shown in Figure 42: • On/Off Switch • USB Port •...
-
Page 60: Figure 43 Controller Board Connectors - Top
All manuals and user guides at all-guides.com Touch Screen System and Setup Figure 43 shows the connectors at the top of the Telephone Access controller. Line 1 Line 5 General Relay Door Strike Output 4 DC Output 1 Door Strike AC or DC Input Door Line 2... -
Page 61: Grounding The 15" Touch Screen
All manuals and user guides at all-guides.com Touch Screen System and Setup Figure 44 shows the connectors at the bottom of the Telephone Access controller. Input 2 Input 3 Input 4 RS-485 OUT - s + LED/LAMP Supply Power Supply for TX3 Microphone Input 1 Input 5... -
Page 62: Connecting To The External Power Supply
All manuals and user guides at all-guides.com Touch Screen System and Setup To ground the 22” Touch Screen Attach the bottom right terminal to a suitable grounding wire and connect it to the site ground, as shown in Figure 45. Power Terminals (not polarity sensitive) -
Page 63: Figure 46 Md-990 Terminal Block Wiring
All manuals and user guides at all-guides.com Touch Screen System and Setup 3.6.2 Maximum Power Supply Wire Distances The distance from the Touch screen to the power supply is a function of the wire gauge and the resistance generated by the cable by the power draw. Do not exceed the maximum distances from the Touch screen to the power supply as indicated in Table 1. -
Page 64: Installing The Postal Lock
All manuals and user guides at all-guides.com Touch Screen System and Setup Connect the building power supply wires to the MD-990 line terminal screws as shown in Figure 46. Connect the other end of the building power supply wires the line voltage terminals. - Page 65 All manuals and user guides at all-guides.com Touch Screen System and Setup Camera. For instructions on installing a Logitech c615 HD Webcam, see 3.13 on page 69. Replacement 22” display. For instructions on installing a replacement 3M Multi-Touch Display, see 3.14 on page 70. Fan.
-
Page 66: Verifying Installed Components
All manuals and user guides at all-guides.com Touch Screen System and Setup There are two additional RS-485 Terminal Connectors that must be added to the FIRST and LAST node of the network. On the FIRST node of the network attach the connector to the RS-484 IN. -
Page 67: Beginning Configuration
All manuals and user guides at all-guides.com Touch Screen System and Setup For additional information about the Telephone Access Controller Board Connectors see LT-969 TX3-Telephone Access System Installation and Operation Manual: Speaker Connections. Audio speakers to Audio Mixer Board. USB. Telephone Access Controller USB to PC Sub Compact Board USB Power Supply Connectors. -
Page 68: Shutting Down The Touch Screen
All manuals and user guides at all-guides.com Touch Screen System and Setup DIP Switch 8 on SW1 determines how the Telephone Access Controller board gets its IP address (only for for IP-enabled Touch Screen models with the TX3-IP Module installed): •... -
Page 69: Installing A Logitech C615 Hd Webcam On The 22" Touch Screen
All manuals and user guides at all-guides.com Touch Screen System and Setup Do not disconnect the power until the full shut down process has been completed. 3.13 Installing a Logitech c615 HD Webcam on the 22” Touch Screen You can install a Logitech c615 HD Webcam in the 22” Touch Screen. To install the Logitech c615 camera Shut down the Touch Screen and disconnect the power. -
Page 70: Replacing The 3M™ Multi-Touch Display C2167Pw On The 22" Touch Screen
All manuals and user guides at all-guides.com Touch Screen System and Setup 3.14 Replacing the 3M™ Multi-Touch Display C2167PW on the 22” Touch Screen The 22” Touch Screen incorporates a 3M™ Multi-Touch Display C2167PW (ID: 98000342422). If you need to replace it, follow these instructions. -
Page 71: Figure 49 Inside Of Door Showing Position Of The Four #6-32 Nuts
All manuals and user guides at all-guides.com Touch Screen System and Setup Remove the four #6 nuts and keep them. Figure 49. Inside of door showing position of the four #6-32 nuts Remove the display from the four posts. TX3 Touch Screen Installation Manual Version 3.4 71 (93) LT-996... -
Page 72: Figure 50 The Two Brackets (Ch-1165) Holding The Display
All manuals and user guides at all-guides.com Touch Screen System and Setup Remove the eight M4x8mm screws and the outside brackets (CH-1165). Keep the brackets and the screws. Figure 50. The two brackets (CH-1165) holding the display To attach the new display Attach the supplied 3M brackets to the display using the supplied M4 screws. -
Page 73: Figure 51 Power Button
All manuals and user guides at all-guides.com Touch Screen System and Setup Slide the display on to the four posts on the door and secure the four #6 nuts on the posts. Note: Make sure to install the display the right way up. The four buttons should be on the bottom. -
Page 74: Installing The Tx3-P300-Ha Card Reader In The 22" Touch Screen
All manuals and user guides at all-guides.com Touch Screen System and Setup 3.15 Installing the TX3-P300-HA Card Reader in the 22” Touch Screen Open the Touch Screen door. Install the fan in the lower left corner of the door, as shown in Figure 52. TX3-P300-HA Card Reader Figure 52. -
Page 75: Figure 53 The Tx3-P300-Ha Card Reader
All manuals and user guides at all-guides.com Touch Screen System and Setup Attach the card reader to the 2 posts on the bracket with the 2 #4-40 nuts as shown in Figure 53. TX3-P300-HA Bracket Posts(x2) Card Reader Nuts (x2) Figure 53. -
Page 76: Installing A Rb-Md-1093 Two Door Controller Network Board
All manuals and user guides at all-guides.com Touch Screen System and Setup 3.16 Installing a RB-MD-1093 Two Door Controller Network Board Refer to the manual LT-981A that came with the two door controller network board for instructions on how to install it. TX3 Touch Screen Installation Manual 76 (93) Version 3.4... -
Page 77: Adding Controllers
All manuals and user guides at all-guides.com Adding Controllers Adding Controllers This chapter provides information about adding additional controllers on the same network as the Touch Screen. This chapter explains • How to add the controller TX3 Touch Screen Installation Manual Version 3.4 77 (93) LT-996... -
Page 78: Adding A Controller
All manuals and user guides at all-guides.com Adding Controllers Adding a Controller The TX3 Touch Screen may be integrated with other controllers, such as the Telephone and Card Access systems, through a peer-to-peer connection via the RS-485 bus. Touch has a provision to add the TX3 Card Access controller inside the unit. Note: Ensure that all network devices each have unique ID addresses. -
Page 79: Appendix
All manuals and user guides at all-guides.com Appendix Appendix This chapter contains additional information about the TX3 Touch Screen. This chapter explains • Touch Screen Specifications • Touch Screen Kits TX3 Touch Screen Installation Manual Version 3.4 79 (93) LT-996 Copyright 2015... -
Page 80: Specifications
All manuals and user guides at all-guides.com Appendix Specifications 5.1.1 Operating Temperature 50°C (122°F) to 0°C (32°F). Do not operate the Touch Screen below 0°C (32°F) at any time. 5.1.2 Telephone Lines Use only Loop Start telephones (not ground start), check with your local telephone company. - Page 81 All manuals and user guides at all-guides.com Appendix 5.1.7 Tamper Switch This switch can be connected to any security or monitoring system to supervise the opening of the panel front door. This microswitch is the same type used for the postal lock. This switch is normally open when the panel front door of the TX3 is closed, 28 Vac or 28 Vdc, 1A.
- Page 82 All manuals and user guides at all-guides.com Appendix TX3 Touch Screen Installation Manual 82 (93) Version 3.4 Copyright 2015 LT-996...
-
Page 83: Resident Operating Instructions
All manuals and user guides at all-guides.com Resident Operating Instructions Resident Operating Instructions This chapter describes the Touch Screen operating instructions for use by the resident. This chapter explains • NSL Resident Operating Instructions • ADC Resident Operating Instructions TX3 Touch Screen Installation Manual Version 3.4 83 (93) LT-996... -
Page 84: Nsl Resident Operating Instructions
All manuals and user guides at all-guides.com Resident Operating Instructions NSL Resident Operating Instructions Mircom's state-of-the-art Touch Screen door entry system provides you and your guest with an increased level of confidence and security. Touch Screen operates with your existing telephone. Your guest dials your code number or selects your name by scrolling through the visual directory on the Touch Screen unit, causing your telephone to ring. - Page 85 All manuals and user guides at all-guides.com Resident Operating Instructions 6.1.3 Call Waiting Feature When a guest places a call to you from the Touch Screen while you are engaged in a conversation on your outside telephone line, you will hear a distinct tone. To answer the call Briefly push the call waiting key to answer the call.
-
Page 86: Adc Resident Operating Instructions
All manuals and user guides at all-guides.com Resident Operating Instructions ADC Resident Operating Instructions Mircom's state-of-the-art Touch Screen door entry system provides you and your guest with an increased level of confidence and security. Touch Screen operates with your existing telephone. Your guest dials your code number or selects your name by scrolling through the visual directory on the Touch Screen unit, causing your telephone to ring. -
Page 87: Warranty & Warning Information
All manuals and user guides at all-guides.com Warranty & Warning Information Limited Warranty Mircom Technologies Ltd. together with its subsidiaries and affiliates (collectively, the “Mircom Group of Companies”) warrants the original purchaser that for a period of two years from the date of manufacture, the product shall be free of defects in materials and workmanship under normal use. - Page 88 All manuals and user guides at all-guides.com • damage arising out of any other abuse, mishandling or improper application of the products. Warranty Procedure To obtain service under this warranty, please return the item(s) in question to the point of purchase. All authorized distributors and dealers have a warranty program.
- Page 89 All manuals and user guides at all-guides.com Products which Mircom determines to be repairable will be repaired and returned. A set fee which Mircom has predetermined and which may be revised from time to time, will be charged for each unit repaired. Products which Mircom determines not to be repairable will be replaced by the nearest equivalent product available at that time.
-
Page 90: Special Notices
All manuals and user guides at all-guides.com Special Notices Product Model Number: TX3 AC REN (U.S.): 0.0B AC REN (CANADA): 0.0 Complies With Federal Communications Commission (FCC): • TIA-968-A Technical requirement for connection of equipment tot he telephone network. • CFR 47, Part 15, Subpart B, Class B •... - Page 91 All manuals and user guides at all-guides.com Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alteration made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
- Page 92 All manuals and user guides at all-guides.com on your telephone lines should be less than five in order to assure proper service from the telephone company. In some cases, a sum of five may not be useable on a given line. Changes to Telephone Service The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment.
- Page 93 All manuals and user guides at all-guides.com Product Identifier This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the back of the front panel cover of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
Need help?
Do you have a question about the TX3 Series and is the answer not in the manual?
Questions and answers