Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for IKM UMA-4856-020
-
Page 1: User Manual For Subsea Drill
USER MANUAL FOR SUBSEA DRILL Document title UMA-4856-020/030 Subsea Drill IKM TECHNOLOGY AS ref. P4856 Customer ref. Subsea Tool Rev. Date Reason For Issue Prepared Checked Approv 02.06.2015 Issued for review 13.06.2016 Update... -
Page 2: Table Of Contents
Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS USER MANUAL FOR SUBSEA DRILL ................1 GENERAL INFORMATION ................3 Abbreviations ....................4 References ....................5 TECHNICAL SPESIFICATION ..............6 SAFETY ....................... 7 General –... -
Page 3: General Information
Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS GENERAL INFORMATION This manual is a user manual for the Subsea Drill tool. The Subsea Drill can roughly drill holes in the 10 to 100 mm range. It is built to be used with a Subsea ROV, controlled by manipulator and hydraulic supply from the ROV to drive the drill. -
Page 4: Abbreviations
2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS Abbreviations Hydraulic Power Unit Remotely Operated Vehicle Kilo gram Milli meter British standard pipe Joint industry council Cubic centimeter Liter per minute... -
Page 5: References
2014.12.29 Approved date: 2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS References Doc nr Description Rev. Issued Can be found 4859-020 rev-03 Drawing of Subsea Drill 09.06.15 Appendix A 4859-030 rev-01 Drawing of Subsea Drill 17.03.16... -
Page 6: Technical Spesification
Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS TECHNICAL SPESIFICATION The Subsea Drill main components is steel frame, drill/hole bits, claws with hydraulic cylinders to hold on to object being drilled and char-lynn 2000 serie motor (305ccm) attached to an cylinder which regulates the cutting feed. -
Page 7: Safety
IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS SAFETY General – Operations Only authorised people and qualified personnel should work on the system, and take suitable precautions to prevent any potential injuries. Always adhere to authorised working practices, and use the correct tools for the job. - Page 8 Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS Always ensure that items are correctly and adequately supported before removal, and that authorised lifting equipment and procedures are used. Note: trying to lift heavy components in an awkward position by hand without the assistance of correct lifting equipment, or lifting any component without adopting the correct stance, can lead to serious injury.
-
Page 9: Operational Description
Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS OPERATIONAL DESCRIPTION The following description is a generic description of preparation and use of the Subsea Drill tool. Customers are advised to adapt the following information to their own specific operations and specific work area. -
Page 10: Feed / Flow Regulator
IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS Connect the hydraulic hoses to the ROV corresponding hydraulic system. Ensure that the piston on the feed cylinder is fully retracted. Function test: Do not start the drill on deck without securing the area. - Page 11 2014.12.29 Approved date: 2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS Retract the cylinders for the clamp. Return to deck and perform “After operations maintenance”, ref chapter 5.
-
Page 12: Maintenance
Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS MAINTENANCE Repair and maintenance work on the drill shall only be performed by qualified personnel, specifically trained on this equipment. After operations Plug hydraulic hoses to prevent hydraulic leaks and dirt to enter the hydraulic system. -
Page 13: Spare Part List
Approved date: 2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS SPARE PART LIST Drill/hole bits Hydraulic hoses and connections. Nuts and bolts. Handles Claws ... -
Page 14: Revision Changes
2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS REVISION CHANGES Revision Procedure change Author Original version Update CONTACT INFORMATION All enquiries relating to the tooling should be addressed to: IKM Technology AS... -
Page 15: Appendix
Issue date: 2014.12.29 Approved date: 2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS APPENDIX Doc number Description Appendix A 4856-020 rev-03 Drawings Subsea Drill Appendix B 4856-030 rev-01 Drawings Subsea Drill... - Page 16 ALL DIMENSIONS ARE IN MILLIMETRES THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF IKM TECHNIQUE AS. NONE OF THE INFORMATION CONTAINED HEREIN MAY BE DISCLOSED, ( 1 : 5 ) TOLERANCES: REPRODUCED, DISTRIBUTED OR USED WITHOUT WRITTEN CONSENT FROM IKM TECHNIQUE AS.
- Page 17 ALL DIMENSIONS ARE IN MILLIMETRES THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF IKM TECHNIQUE AS. NONE OF THE INFORMATION CONTAINED HEREIN MAY BE DISCLOSED, TOLERANCES: REPRODUCED, DISTRIBUTED OR USED WITHOUT WRITTEN CONSENT FROM IKM TECHNIQUE AS. LINEAR: ISO 2768-1...
- Page 18 ALL DIMENSIONS ARE IN MILLIMETRES THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF IKM TECHNIQUE AS. NONE OF THE INFORMATION CONTAINED HEREIN MAY BE DISCLOSED, TOLERANCES: REPRODUCED, DISTRIBUTED OR USED WITHOUT WRITTEN CONSENT FROM IKM TECHNIQUE AS. LINEAR: ISO 2768-1...
- Page 19 ALL DIMENSIONS ARE IN MILLIMETRES THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF IKM TECHNIQUE AS. NONE OF THE INFORMATION CONTAINED HEREIN MAY BE DISCLOSED, TOLERANCES: REPRODUCED, DISTRIBUTED OR USED WITHOUT WRITTEN CONSENT FROM IKM TECHNIQUE AS. LINEAR: ISO 2768-1...
- Page 20 ALL DIMENSIONS ARE IN MILLIMETRES THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF IKM TECHNIQUE AS. NONE OF THE INFORMATION CONTAINED HEREIN MAY BE DISCLOSED, TOLERANCES: REPRODUCED, DISTRIBUTED OR USED WITHOUT WRITTEN CONSENT FROM IKM TECHNIQUE AS. LINEAR: ISO 2768-1...
- Page 21 ALL DIMENSIONS ARE IN MILLIMETRES THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF IKM TECHNIQUE AS. NONE OF THE INFORMATION CONTAINED HEREIN MAY BE DISCLOSED, TOLERANCES: REPRODUCED, DISTRIBUTED OR USED WITHOUT WRITTEN CONSENT FROM IKM TECHNIQUE AS. SIDE VIEW CLAMP CLOSED...
- Page 22 ALL DIMENSIONS ARE IN MILLIMETRES THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF IKM TECHNIQUE AS. NONE OF THE INFORMATION CONTAINED HEREIN MAY BE DISCLOSED, TOLERANCES: REPRODUCED, DISTRIBUTED OR USED WITHOUT WRITTEN CONSENT FROM IKM TECHNIQUE AS. LINEAR: ISO 2768-1...
- Page 23 ( 1 : 8 ) IN MILLIMETRES THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF IKM TECHNIQUE AS. NONE OF THE INFORMATION CONTAINED HEREIN MAY BE DISCLOSED, TOLERANCES: REPRODUCED, DISTRIBUTED OR USED WITHOUT WRITTEN CONSENT FROM IKM TECHNIQUE AS.
Need help?
Do you have a question about the UMA-4856-020 and is the answer not in the manual?
Questions and answers