Bakeey TS-WP10 User Manual

Bathroom clock

Hide thumbs

page of 32

/ 32
Bookmarks

Quick Links

Download this manual

TS-WP10 User Manual

Summary of Contents for Bakeey TS-WP10

Page 1 TS-WP10 User Manual...
Page 2 TS-WP10 Bathroom Clock: H AL o L AL H AL o L AL MIN MAX MIN MAX Display of all functions...
Page 3 Meanings of display: Minute Countdown A.M./P.M. Time display Time icon Second Snooze icon Countdown Alarm icon clock icon Alarm icon Dynamic seconds Max./Min. countdown o L AL o L AL H AL H AL H AL o L AL H AL o L AL values Temperature unit...
Page 4 Buttons: One-button snooze/turn on backlight SNOOZE/LIGHT CLEAR Start countdown Start countdown Revolving clip-on rear cover MODE ALERT Wall mounting hole Mode Beyond View Backward selection -limit max./min. adjustment alarm values °C/°F switch Transparent Forward settings silicone suction cup adjustment Foldable support...
Page 5 Thank you for purchasing the TS-WP10 bathroom clock. The user’s guide for operations is given as follows: 1.Major functions: Hour, minute, second, temperature, humidity, and simulated time are displayed on the same screen Two alarm clocks Snooze function: Five minutes by default...
Page 6 Backlight color prompt for beyond-limit temperature/humidity Temperature/Humidity calibration function Waterproof grade: IPX4 2.Power supply: 1. Power supply through USB DC power cable(when the DC cable is plugged in, the backlight indicator turns on for 8 seconds, and then automatically dies out if no buttons are pressed.
Page 7 2. Powered by 3 AAA batteries (the clock is not always on when powered by batteries). Remarks: This clock is shipped without batteries. AAA battery * 3 MODE ALERT USB DC power cable...
Page 8 3. Power on and reset: When this clock is powered on, the LED is fully displayed for 3 seconds, and the backlight color alternates in the order of red, orange, and white for one cycle. The initial interface of the system is displayed after a beep sound. Default display after startup: white backlight Time: 0:00...
Page 9 4. Time settings: In the time display mode, jump to the setup page by long pressing [MODE], when the parameters to be set up are displayed and flashing; the setup sequence is: 12HR/24HR→hour→minute→exit and return to normal time display. In time settings, short press [＋] if you want to add the value by 1 or long press [ ] for ＋...
Page 10 In the alarm clock review mode, the alarm clock can be turned on or off by short pressing [＋]. During setting, select 1 alarm clock and long press [MODE] for at least 3 seconds, when the Hour place starts flashing; then short press [MODE] and the Minute place starts flashing.
Page 11 6. Snooze mode: When the alarm clock is ringing, short press [CLEAR] if you want to go to the 5-minute snooze mode, or any other button to silence the alarm clock. SNOOZE/LIGHT CLEAR Top touch button 7. Countdown settings: In the countdown mode, the numbers of the current time show the minute and second countdown values, and the second point is fixed without flashing (but the MS and the sandglass flash once every second as prompt).
Page 12 circle of the entire countdown. When the countdown hits zero, both the outer ring and inner ring disappear. The innermost round spot flashes. Meanwhile, the numbers show 00:00 and flash accordingly. In the time display mode: 1. Short press [10] to set up the countdown duration. Every pressing within 3 seconds increases the duration by 10 minutes.
Page 13 2. Short press [1] to set up the countdown duration. Every pressing within 3 seconds increases the duration by 1 minute. The longest duration allowed is 99 minutes. 3. Short press the [10] , and then long press the [10] , press a multiple of 10 minutes to quickly accumulate the countdown time, up to 99 minutes.
Page 14 9. When the countdown hits zero, the clock gives intermittent beep sounds that will stop after 2 minutes if no action is taken. Short pressing any button can stop the beep sound anytime. Attention: If you choose to set up another function when a countdown is in action, the clock shows the setup interface of this function.
Page 15 In the time display mode, long press [ALERT] if you want to set up the temperature/humidity alarm. In this setting mode, short press [＋] if you want to increase the value by 1, or long press [＋] for quick increase (8 steps/s); short press[－] if you want to decrease the value by 1, or long press [－] for quick decrease (8 steps/s).
Page 16 When the temperature or humidity alarm conditions are triggered, the corres ponding alerting color is displayed, and the clock gives beep sound for 5 seconds. The corresponding alarm icon keeps flashing, until the triggering conditions no longer exist. If no action is taken, the corresponding alerting color is displayed every minute, accompanied by the beep sound that lasts for 5 seconds.
Page 17 or long press [－]for a quick decrease (8 steps/s). After temperature settings are complete, press [MODE] to go to the humidity value calibration mode. In this mode, short press [＋] if you want to increase the humidity value by 1, or long press [＋] for quick increase (8 steps/s);...
Page 18 In the setting mode, short/long press this button if you want to increase values by one step or several steps. 11. [－] button functions: In the normal time display mode (no settings are ongoing), short press this button if you want to switch the temperature unit between °C and °F. In the setting mode, short/long press this button if you want to decrease values by one step or several steps.
Page 19 TS-WP10 中文说明书...
Page 20 TS-WP10浴室钟: H AL o L AL H AL o L AL MIN MAX MIN MAX 功能全显图...
Page 21 显示说明: 倒计时显示上午/下午时间显示时间图标分秒贪睡图标倒计时图标闹钟图标报警图标倒计时动态退秒指示圈最大值/ o L AL o L AL H AL H AL H AL o L AL H AL o L AL 最小值温度单位显示温度显示动态时钟显示湿度显示时间显示模式倒计时显示模式...
Page 22 按键说明: 一键贪睡/开启背光灯 SNOOZE/LIGHT CLEAR 进入倒计时进入倒计时旋转卡扣式后盖 MODE ALERT 挂墙孔模式选择越限报查看最大值向后调整警设置 /最小值 ℃/℉切换向前调整透明硅胶吸盘折叠支撑架...
Page 23 感谢您购买使用TS-WP10，以下是用户使用操作指南：一、产品主要功能：时，分，秒，温湿度，模拟时间同屏显示两组闹钟贪睡功能，默认五分钟倒计时功能倒计时动态进度条指示圈倒计时动态退秒指示圈室内温度（测量范围: 0℃~ 50 ℃/32℉~122℉） , 刷新时间: 30 秒. 分辨率: 0.1 ℃. 室内湿度（测量范围: 20% ~ 99%）刷新时间: 30 秒. 分辨率: 1%. 室内温度湿度最大最小值设置室内温度湿度越限值温湿度越限警示颜色背光提示温度湿度校准功能防水等级：IPX4...
Page 24 二、供电方式： 1.USB DC电源线供电（当插入DC电源线供电时，背光会亮8秒后，在没有操作任何按键时，会自动熄灭。如需要背光长亮，可通过长按【CLEAR 】键2秒以上，Bi 一声提示后，并打开常亮背光状态。如需关闭长亮，同样长按【CLEAR】键2秒以上，Bi一声提示音后关闭背光。在倒计时运行和报警期间，不论有没插DC，背光都是长亮）。 2.3节7号电池供电（电池供电时，产品无法常亮）。备注：产品发货不含电池。 3节7号电池 MODE ALERT USB DC电源线...
Page 25 三、上电及复位：产品通电，LED全显3秒，背光颜色红橙白循环一遍，BI一声后显示系统初始界面。开机后默认显示：背光颜色白光时间：0:00 默认时间制式：24小时制默认单位：温度【℃】相对湿度【%】...
Page 26 四、时间设置：在时间显示模式下，长按【MODE】键，进入设置状态，进入后，其设置项目显示并闪烁，设置顺序为：12HR/24HR → 小时 → 分钟→退出设置返回正常时间显示模式设置时，单按【＋】键，加一，长按【＋】键，快加（8步/秒），单按【－】键，减一，长按【－】键，快减（8步/秒）。五、闹钟设置：在时间显示模式下，短按【MODE】键，切换到闹钟显示，切换顺序为：正常时间显示→闹钟1 → 闹钟2→正常时间显示。...
Page 27 在闹钟查看模式下，短按【＋】键，可开启或关闭闹钟功能。设置闹钟时，选择1组闹钟，长按【MODE】键3秒以上，小时开始闪烁，在短按【MODE】键分钟开始闪烁，设置时，单按【＋】键，加一，长按【＋】键，快加（8步/秒），单按【－】键，减一，长按【－】键，快减（8步/秒），在短按【MODE】键将自动保存设置并退出设置模式。六、贪睡模式：在闹钟响闹模式，短按【CLEAR】键进入5分钟贪睡模式，按其它任意键则退出响闹响闹模式。 SNOOZE/LIGHT CLEAR 顶部触摸按键...
Page 28 七、倒计时设置：倒计时运行时，当前时间数字位置显示倒计时分秒数值及秒点固定不闪动（但MS 及沙漏1秒1次闪动提醒）。模拟部分则外圈为秒，内圈为整个倒计时计时进度动态圈。当最后到达0分0秒时，内外圈均消失。最内部分圆点闪动。同时数字显示00：00，并对应闪动。...
Page 29 在时间显示模式下： 1、短按【10】键设置倒计时时间，3秒内每按一次累加10分钟，最多至99分钟。 2、短按【1】键设置倒计时时间，3秒内每按一次累加1分钟，最多至99分钟。 3、先短按【10】键，再长按【10】键，按10分钟倍数快速累加倒计时时间，最多至 99分钟。 4、先短按【1】键，再长按【1】键，按2步/秒，逐分钟快速累加倒计时时间，最多至 99分钟。 5、在设置时间过程中，短按【CLEAR】键可随时清零退出倒计时设置。 6、设定倒计时，按键3秒内无操作，倒计时自动开启，同时发出一声BI音。 7、倒计时设置时，时间位置显示正在设置倒计时的时长，左上角固定显示MS和沙漏符号（不闪动）。 8、在倒计时工作中，短按【CLEAR】键可随时清零退出倒计时状态，同时发出一声 BI音。 9、倒计时结束到点时，发出BiBiBiBi间歇响闹提示，响闹最长时间为2分钟停止，短按任意键可随时取消响闹。注意：当在运行倒计时功能时，如有进入其它设置功能，则显示界面进入其它对应显示界面。但无操作3 秒后自动返回倒计时显示界面。如倒计时完成后。倒计时响闹提醒2分钟。如在2分钟内有任意按键按下，退出倒计...
Page 30 时响闹提醒并返回当前时间显示界面。如响闹提醒2分钟后无任意按键按下，则自动返回当前时间显示界面。八、温湿度上/下限报警设置：在时间显示模式下，短按【ALERT】键，开启或关闭温湿度报警功能。  在时间显示模式下，长按【ALERT】键，进入温湿度报警设置模式，设置时，单按【＋】键，加1，长按【＋】键，快加（8步/秒），单按【－】键，减1，长按【－】键，快减（8步/秒），设置顺序为，温度报警上限（红色背光提醒）→ 温度报警下限（橙色背光提醒）→ 湿度报警上限（红色背光提醒）→ 湿度报警下限（橙色背光提醒） →退出设置。 H AL o L AL H AL o L AL 报警功能开启报警功能关闭...
Page 31 当触发温度或湿度报警条件时，时钟对应警示颜色开启并伴随哔哔哔的响闹声5秒钟，对应报警图标会一直闪烁，直到温度和湿度的条件不再有效，在无操作情况下，每隔一分钟时钟对应警示颜色开启并伴随哔哔哔的响闹声5秒钟，按任意键使报警静音。备注：默认温度上限为50℃，下限为0℃，湿度上限为99%,下限为20%。温度设置数值状态下数值按每次0.1增加，湿度设置数值状态下数值按每次1增加。九、温湿度校准功能：在时间显示模式下，同时按【MODE】键和【＋】键，进入温度数值校准状态，设置时，短按【＋】键，对应温度加0.1，长按【＋】键，快加（8步/秒），短按【－】键，对应温度减0.1，长按【－】键，快减（8步/秒）。设置完成后，按【MODE】键进入湿度数值校准状态，短按【＋】键，对应湿度加1，长按【＋】键，快加（8步/秒），短按【－】键，对应湿度减1，长按【－】键，快减（8步/秒）。设置完成后，按【MODE】键确认并退出设置模式。...
Page 32 十、【＋】按键功能：在非设置状态下，在正常时间显示模式，短按此键，查看温湿度 MAX /MIN值。在非设置状态下，在温湿度 MAX /MIN查看模式下，长按此键，可清除温湿度 MAX /MIN记录值。在非设置状态下，在闹钟查看模式下，短按此键，可开关闹钟功能。在设置状态下，短按/长按此键，可进行单步/快加动作。十一、【－】按键功能：在非设置状态下，在正常时间显示模式，短按此键，切换温度单位℃/℉ 在设置状态下，短按/长按此键，可进行单步/快减动作。 RoHS MADE IN CHINA...