Important Safety Instructions 1. Read these instructions. CAUTION 2. Keep these instructions. 3. Heed all warnings. RISK OF ELECTRIC SHOCK. DO NOT OPEN. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7.
Page 3
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.).
Page 5
Each model in the lineup will accept both high-level or low-level inputs, allowing the Party Mode wireless pairing Infinity amplifiers to be added to virtually any car audio system, including factory installed Cabin-mounted control panel systems. The 2-, 4- and 5-channel amplifiers offer Bluetooth audio streaming, exclusive ®...
KAPPA AMPLIFIERS World’s first Amplifiers with Clari-fi Technology Product specifications: High Performance 2-Channel Full Range Car Audio Power Amplifier Max Power: 700W Peak Power Output, 4Ω: 100Wrms x 2, <0.1% THD+N Power Output, 2Ω: 120Wrms x 2, <0.1% THD+N Power Output, 4Ω Bridged: 240Wrms x 1, <0.3% THD+N Signal-to-Noise Ratio: >75dB (ref 1W output @ 4Ω) Bluetooth Audio Streaming...
Page 7
K4 Block Diagram K4 Block Diagram Audio Signal: MCU UART Power Signal: oscillator Control Signal: BM153 MCLK Analog for Speech upgrade I2S for Music LINE OUTPUT LINE OUTPUT GAIN WM8281 GAIN GAIN HI*4 MCU UART ADC*4 FOR LCD control control STM32F103C8 STM32F103C8 128K (105 ) 4 Channel Audio Crossover expander DET (6V) DET (6V) Audio DET...
Page 13
CONNECT PRE-AMP TO AMP AGND BT_AL_P ③ BT_AR_P BT_AL_N BT_AR_N AGND AGND POWER LED POWER LED APJ1A WM8281-MODULE Clari-Fi LED Clari-Fi LED PRE( 前级 ) 同 AMP( 功放 板 ) 连接 (APJ2B) Party Mode LED Party Mode LED ⑦ BT LED BT LED PRE (前级)同AMP(功放板)连接(APJ2AB) AGND...
Page 17
CONNECT (AMP) Party Mode LED BT LED AUTO OFF AUTO OFF Clari-Fi LED PAGE 14/19 PROT LED PROT LED POWER LED PROT LED PROT3 PROT3 PAGE 16/19 PROT_85C PROT_85C PRE( AMP( (APJ2AB) 前级 同 功放板 连接 PROT_2 PROT_2 PROT_2 ③ PAGE 7/19 PROT_85C ③...
Revision List Version 1.0 Initial Release Version 1.1 Correction to Gift Box P/N. Version 1.2 Delete Pre-amp Board on Mech. Exploded View and Parts List. Version 1.3 Add REM Connector in Parts List.
Need help?
Do you have a question about the Kappa Series and is the answer not in the manual?
Questions and answers