Toro Pro Force Groundsmaster 3200 Series Operator's Manual
Hide thumbs
Also See for Pro Force Groundsmaster 3200 Series:
- Service manual (274 pages) ,
- Operator's manual (44 pages) ,
- Installation instructions manual (24 pages)
Related Manuals for Toro Pro Force Groundsmaster 3200 Series
Summary of Contents for Toro Pro Force Groundsmaster 3200 Series
- Page 1 Form No. 3449-239 Rev A Pro Force ® Debris Blower Groundsmaster ® 3200 or 3300 Series Traction Unit Model No. 31916—Serial No. 400000000 and Up *3449-239* Register at www.Toro.com. Original Instructions (EN)
- Page 2 Whenever you need service, genuine Toro parts, or g000502 additional information, contact an Authorized Service Figure 2 Dealer or Toro Customer Service and have the model Safety-alert symbol and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product.
-
Page 3: Table Of Contents
Contents Safety Safety ............... 3 General Safety General Safety ........... 3 Safety and Instructional Decals ......3 This product is capable of amputating hands and Setup ................ 5 feet and throwing objects. Always follow all safety 1 Removing the Blower from the Crate ....6 instructions to avoid serious personal injury. - Page 4 decal137-3999 137-3999 decal144-3323 1. Warning—read the 3. Warning—wear hearing 144-3323 Operator’s Manual. and eye protection. 2. Thrown object 4. Cutting/dismemberment 1. Read the Operator’s 3. Service every 8 hours hazard—keep bystanders hazard of hands—shut Manual before performing away from the machine. off the engine;...
-
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Caster Bolt Remove the blower from the crate. Flange locknut Mounting plate assembly Install the mounting plate to the debris Bolt (1/2 x 1-1/4 inches) blower frame. -
Page 6: Removing The Blower From The Crate
Removing the Blower from the Crate Parts needed for this procedure: Caster Bolt Flange locknut g362310 Figure 4 Bolt (1/2 x 3-1/2 inch) 3. Flange locknut (1/2 inch) Procedure 2. Caster wheel Important: Ensure that the jack stand is installed to stabilize the blower before you unbolt the Secure a strap to the top end assembly and lift blower frame from the shipping crate or remove... - Page 7 g362315 Figure 8 1. Frame tube 3. Jack stand 2. Snapper pin Remove the cable tie securing the crank handle to the jack crank. Crank the jack stand down until the jack pad is g363311 level with the castor wheel tires. Figure 6 Carefully remove the bolts holding the blower 1.
-
Page 8: Installing The Mounting Plate To The Debris Blower Frame
Installing the Mounting Plate to the Debris Blower Frame Parts needed for this procedure: Mounting plate assembly g362312 Figure 11 Bolt (1/2 x 1-1/4 inches) Locknut (1/2 inch) 1. Locknuts 3. Bolts 2. Mounting plate assembly Procedure Torque the bolts to 92 to 113 N∙m (68 to 82 ft-lb). Remove the bolts securing the mounting plate Secure the safety chains to the mounting plate assembly to the crate... -
Page 9: Mounting The Debris Blower To The Traction Unit
Secure the front of the lift arms to the mounting assembly using the 2 hex-head bolts and 2 curved washers removed from the attachment in 3 Preparing the Traction Unit (page 8) as shown Figure Mounting the Debris Blower to the Traction Unit Parts needed for this procedure: Debris blower assembly U-bolt... -
Page 10: Installing The Jack Stand To The Storage Tube
dust plugs are cleaned and then installed to prevent contamination from entering either hydraulic system. Installing the Jack Stand to the Storage Tube No Parts Required g350949 Figure 14 Procedure 1. Capscrew 3. Locknut 2. Washer After you install the blower to the traction unit, remove the jack stand from the frame tube and use the Tighten the PTO connection hardware;... -
Page 11: Installing The Whip Guides
Installing the Whip Guides Parts needed for this procedure: Whip guide Whip guide bracket U-bolt Hex-head bolt (5/16 x 1 inch) Flange nut (3/8 inch) Flange nut (5/16 inch) Procedure Use 4 bolts (5/16 x 1 inch), 4 flange nuts (5/16 inch), 2 U-bolts, 4 flange nuts (3/8 inch), and 2 whip guide brackets to install the whip guides to the caster arms g367853... -
Page 12: Operation
During Operation Safety Operation • The owner/operator can prevent and is responsible for accidents that may cause personal injury or Note: Determine the left and right sides of the property damage. machine from the normal operating position. • Wear appropriate clothing, including eye Important: Only engage the PTO at low idle;... -
Page 13: Adjusting The Blower Nozzle Height
Adjusting the Blower operate the machine, review the site conditions to determine whether you can operate the machine Nozzle Height in the conditions on that day and at that site. Changes in the terrain can result in a change in The blower nozzle can be operated at a height range slope operation for the machine. -
Page 14: Operating Tips
Operating Tips WARNING Discharged air has considerable force and could cause injury or loss of footing. • Stay away from the nozzle opening while the machine is operating. • Keep bystanders away from the nozzle opening while the machine is running. •... -
Page 15: Maintenance
Toro distributor. • Altering this machine in any manner may affect the operation of the machine, performance, durability, or its use may result in injury or death. Such use could void the product warranty of The Toro® Company. g011557 Figure 22... -
Page 16: Lubricating The Driveshaft
Lubricating the Driveshaft Service Interval: Before each use or daily The mounting kit drive shaft has bearings and bushings that you must lubricate regularly. If you are operating the machine under normal conditions, lubricate bearings with No. 2 lithium grease. Lubricate fittings immediately after every washing, regardless of the interval listed. -
Page 17: Checking The Gearbox Lubrication
Checking the Gearbox Check the oil level to make sure it is up to the plug hole in the gearbox. If the lubricant level is Lubrication low, add enough SAE 80-90 weight gear lube to raise the level up to the hole. Service Interval: Every 50 hours Install the check/fill plug to the gearbox. -
Page 18: Adjusting The Nozzle Belt
Cleaning the Nozzle Guides Adjusting the Nozzle Belt Check and remove any grass, dirt or debris buildup Service Interval: After the first 8 hours around and in between the nozzle guides (Figure 27). Every 50 hours Keep the nozzle free of debris to prevent the motor Adjust the belt if the belt slips when changing direction from stalling. -
Page 19: Storage
Storage Remove grass clippings, dirt, and grime from the external parts of the entire blower. Important: You can wash the machine with mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water. Check and tighten all bolts and nuts. Replace any worn parts. - Page 20 Notes:...
- Page 21 Notes:...
- Page 22 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 23 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.
- Page 24 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.