Advertisement
Step 6 - Attach
garden hose
cap (as shown).
Bobber Gauge -
Empty tank
Remove garden hose cap and install
bobber gauge. Once tank is full (you
can tell from the bobber gauge), it
needs to be emptied. Remove the
sewer hose from trailer waste valve
and the tank (you don't want to tow
the tank with the sewer hose
attached). Attach the 3" cap to top of
tank (where sewer hose was located).
Now you can hook the tow handle to
the hitch ball on whatever you have to
drive around (car, golf cart, bike, etc.)
Bring your sewer hose...you will use it at the dump site. (If you are done camping,
bring your grey garden hose so you can rinse your tank.) At the dump site, attach
one end of the sewer hose to the side of your tank and the other end to the dump
station. Remove the garden hose cap or bobber gauge for ventilation. Open the valve on the side of the tank by pulling up on the
black handle and contents of tank will empty.
Now you take the grey water hose and attach it where it was vented. You can hook up the water supply at the dump station and rinse
your tank (if you are done camping). Put both 3" caps back on empty tank and take your accessories with you back to camp.
ITEM
PART NO.
REQ'D
1
26060
2
2
25905
1
3
25911
1
4
25910
1
5
600-0055
1
6
610-1020
1
7
15655
1
8
10225
3
9
10400
2
10
11576
1
11
26048
2
12
25912
1
13
643-0007
1
14
12316
1
15
27183
1
16
25916
2
17
32273
2
18
25918
1
19
25921
2
20
25922
1
21
600-0056
4
22
600-0054
4
23
615-0001
2
24
615-0002
2
25
617-0083
2
25
617-0098
2
26
635-0019
4
27
32274
2
28
610-0025
4
29
26136
1
30
25903
1
31
25923
1
32
26097
1
33
17274
1
34
30955
1
35
26096
2
Barker Manufacturing Co.
269-965-2371 or 888-367-6978
At campsite, take assembled sewer
hose and attach one end on the top of
the tank (as shown in this picture) and
the other end to waste valve on trailer.
Sewer hose
attached to
side--ready to
pull up handle
and empty.
DESCRIPTION
ADAPTOR ASSEMBLY (3")
SPINDLE ASSEMBLY
TOW BAR
AXLE SUPPORT
HEX BOLT (#10-32 X .38)
HEX NUT (#10-32)
FILLER HOSE ASSEMBLY
HOSE WASHER
HOSE CLAMP
HOSE CAP (3/4")
CAP (3")
CAPLUG (#FP-205)
QUICK RELEASE PIN
SEWER HOSE (5')
FRONT AXLE
RETAINER PLATE DUMP VALVE
WHEEL (6" )
SPINDLE BEARING
VALVE SEAL (3")
BAYONET AND FLANGE (3")
HEX HEAD BOLT (1/4-20 X .62)
HEX HEAD BOLT (1/4-20 X 2)
PUSH NUT (5/8")
PUSH NUT (1/2")
BUSHING (42 GAL) (25 GAL)
BUSHING (32 GAL)
"O" RING
WHEEL, REAR (10")
FLANGE NUT
REAR AXLE
TANK 25 GALLON
WASTE VALVE (3")
STRAP (3")
WARNING LABEL (25 & 32 ONLY)
BOBBER GAUGE
GASKET
1125 Watkins Road / PO Box 460
E-Mail:
sales@barkermfg.com
Make sure the valve on the side is
closed and the 3" cap is securely
attached.
Gate valve
CLOSED
(handle pushed
DOWN)--attach
3" cap.
Gate valve
Bobber Gauge -
OPEN (handle
Full tank--time
pulled UP-cap
to empty
removed).
IMPORTANT NOTES: Do not tow your
tank faster than 5 mph (or walking speed).
This may damage tank or wheels and will
NOT be covered under warranty.
pneumatic tires may need air periodically.
Inflate with a bicycle air pump.
compressor may over inflate and damage
tire tubes (not covered under warranty).
Battle Creek, MI 49016
Garden hose filler
attached--ready to hook
to water supply to rinse
tank.
The
An air
Advertisement
